From: bugzilla-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 85101] hpsa + P410 does not show connected HP SAS port expanders
Date: Wed, 24 Sep 2014 21:33:38 +0000 [thread overview]
Message-ID: <bug-85101-11613-AaLrfiEiSd@https.bugzilla.kernel.org/> (raw)
In-Reply-To: <bug-85101-11613@https.bugzilla.kernel.org/>
https://bugzilla.kernel.org/show_bug.cgi?id=85101
--- Comment #2 from linux-ide@crashplan.pro ---
In this case the hardware seems broken.
The P410 controller is only used for upgrading the HP SAS expander firmware.
This time we started with upgrading the controller firmware:
===
./ccissflash
This program consists of two phases: device discovery and device update.
No device will be updated until you answer.
Do you want to run device discovery?
(yes/no) yes
Finding hardware. This may take a few minutes.
Found 1 devices.
Do you want to upgrade the device that has older ROM?
(yes/no) yes
1 devices will be updated.
Updating: P410 Slot: 2 from [5.70] to [6.60]
Updating: P410 Slot: 2 from [5.70] to [6.60]
As part of the reboot process, you must power cycle the server and any external
array storage devices.
===
After power cycling the first three reboots were ok. Then a controller lockup
0x00130000 occurred 468 seconds after loading the hpsa module. Since then only
one boot/module loading was ok and since then the "time outs" are occurring:
===
[ 121.613269] HP HPSA Driver (v 3.4.0-1)
[ 121.613344] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 121.613447] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 121.613669] hpsa 0000:01:00.0: MSIX
[ 121.613770] hpsa 0000:01:00.0: irq 46 for MSI/MSI-X
[ 121.613843] hpsa 0000:01:00.0: irq 47 for MSI/MSI-X
[ 121.613909] hpsa 0000:01:00.0: irq 48 for MSI/MSI-X
[ 121.613981] hpsa 0000:01:00.0: irq 49 for MSI/MSI-X
[ 121.614046] hpsa 0000:01:00.0: irq 50 for MSI/MSI-X
[ 121.614117] hpsa 0000:01:00.0: irq 51 for MSI/MSI-X
[ 121.614182] hpsa 0000:01:00.0: irq 52 for MSI/MSI-X
[ 121.614251] hpsa 0000:01:00.0: irq 53 for MSI/MSI-X
[ 121.634560] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 46 using DAC
[ 127.171906] scsi4 : hpsa
[ 127.174883] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 127.175961] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
[ 127.176335] scsi 4:3:0:0: Attached scsi generic sg1 type 12
[ 424.473998] HP HPSA Driver (v 3.4.0-1)
===
[ 16.127857] HP HPSA Driver (v 3.4.0-1)
[ 16.127927] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 16.128020] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 16.128231] hpsa 0000:01:00.0: MSIX
[ 16.128327] hpsa 0000:01:00.0: irq 46 for MSI/MSI-X
[ 16.128394] hpsa 0000:01:00.0: irq 47 for MSI/MSI-X
[ 16.128460] hpsa 0000:01:00.0: irq 48 for MSI/MSI-X
[ 16.128524] hpsa 0000:01:00.0: irq 49 for MSI/MSI-X
[ 16.128590] hpsa 0000:01:00.0: irq 50 for MSI/MSI-X
[ 16.128660] hpsa 0000:01:00.0: irq 51 for MSI/MSI-X
[ 16.128726] hpsa 0000:01:00.0: irq 52 for MSI/MSI-X
[ 16.128791] hpsa 0000:01:00.0: irq 53 for MSI/MSI-X
[ 16.149110] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 46 using DAC
[ 34.767566] scsi4 : hpsa
[ 34.770583] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 34.771054] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
===
[ 48.389920] HP HPSA Driver (v 3.4.4-1)
[ 48.389985] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 48.390059] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 48.390239] hpsa 0000:01:00.0: MSIX
[ 48.390312] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 48.390362] hpsa 0000:01:00.0: irq 31 for MSI/MSI-X
[ 48.390453] hpsa 0000:01:00.0: Logical aborts not supported
[ 48.410617] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 30 using DAC
[ 53.947809] scsi host4: hpsa
[ 53.953488] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 53.953986] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
===
[ 17.076307] HP HPSA Driver (v 3.4.4-1)
[ 17.076388] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 17.076483] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 17.076695] hpsa 0000:01:00.0: MSIX
[ 17.076782] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 17.076837] hpsa 0000:01:00.0: irq 31 for MSI/MSI-X
[ 17.076942] hpsa 0000:01:00.0: Logical aborts not supported
[ 17.097108] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 30 using DAC
[ 33.659110] scsi host4: hpsa
[ 33.663958] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 33.664360] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
[ 33.665053] scsi 4:3:0:0: Attached scsi generic sg1 type 12
[ 485.066696] hpsa 0000:01:00.0: Controller lockup detected: 0x00130000
===
[ 49.567169] HP HPSA Driver (v 3.4.4-1)
[ 49.567251] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 49.567389] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 49.567576] hpsa 0000:01:00.0: MSIX
[ 49.567649] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 49.567705] hpsa 0000:01:00.0: irq 31 for MSI/MSI-X
[ 49.567799] hpsa 0000:01:00.0: Logical aborts not supported
[ 49.587966] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 30 using DAC
[ 55.125143] scsi host4: hpsa
[ 55.129439] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 55.129832] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
===
[ 38.305788] HP HPSA Driver (v 3.4.4-1)
[ 38.305854] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 38.306052] hpsa 0000:01:00.0: MSIX
[ 38.306127] hpsa 0000:01:00.0: irq 29 for MSI/MSI-X
[ 38.306179] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 163.163631] hpsa 0000:01:00.0: board not ready, timed out.
===
[ 23.324890] HP HPSA Driver (v 3.4.0-1)
[ 23.324957] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 23.325060] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 23.325281] hpsa 0000:01:00.0: MSIX
[ 23.325379] hpsa 0000:01:00.0: irq 45 for MSI/MSI-X
[ 23.325453] hpsa 0000:01:00.0: irq 46 for MSI/MSI-X
[ 23.325518] hpsa 0000:01:00.0: irq 47 for MSI/MSI-X
[ 23.325591] hpsa 0000:01:00.0: irq 48 for MSI/MSI-X
[ 23.325655] hpsa 0000:01:00.0: irq 49 for MSI/MSI-X
[ 23.325728] hpsa 0000:01:00.0: irq 50 for MSI/MSI-X
[ 23.325793] hpsa 0000:01:00.0: irq 51 for MSI/MSI-X
[ 23.325865] hpsa 0000:01:00.0: irq 52 for MSI/MSI-X
[ 148.185212] hpsa 0000:01:00.0: board not ready, timed out.
===
Right now loading the hpsa module permanently errors out with "board not ready,
timed out" and the "DS1: Diagnostics Error" LED turns Amber (=One of the server
diagnostics utilities has detected a controller error.)
Seems like a hardware issue, therefore this case can be closed.
--
You are receiving this mail because:
You are watching the assignee of the bug.
next prev parent reply other threads:[~2014-09-24 21:33 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-24 16:46 [Bug 85101] New: hpsa + P410 does not show connected HP SAS port expanders bugzilla-daemon
2014-09-24 18:22 ` [Bug 85101] " bugzilla-daemon
2014-09-24 21:33 ` bugzilla-daemon [this message]
2014-09-24 22:32 ` bugzilla-daemon
2014-09-25 10:48 ` bugzilla-daemon
2014-09-25 10:49 ` bugzilla-daemon
2014-09-25 14:05 ` bugzilla-daemon
2014-09-25 22:22 ` bugzilla-daemon
2014-09-25 22:35 ` bugzilla-daemon
2014-09-25 22:42 ` bugzilla-daemon
2014-10-01 21:59 ` bugzilla-daemon
2023-11-08 9:42 ` bugzilla-daemon
2025-09-18 9:57 ` bugzilla-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=bug-85101-11613-AaLrfiEiSd@https.bugzilla.kernel.org/ \
--to=bugzilla-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.