From: Quentin Schulz <quentin.schulz@cherry.de>
To: Jonas Karlman <jonas@kwiboo.se>,
Kever Yang <kever.yang@rock-chips.com>,
Tom Rini <trini@konsulko.com>,
Ilias Apalodimas <ilias.apalodimas@linaro.org>,
Lukasz Majewski <lukma@denx.de>, Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.u-boot-project.org
Subject: Re: [PATCH 09/15] clk: rockchip: rk3588: Fix ACLK_BUS_ROOT rate set during probe
Date: Fri, 7 Aug 2026 17:44:53 +0200 [thread overview]
Message-ID: <c59fea96-266e-47bf-9d87-d008800b536c@cherry.de> (raw)
In-Reply-To: <20260730141308.1218014-10-jonas@kwiboo.se>
Hi Jonas,
On 7/30/26 4:12 PM, Jonas Karlman wrote:
> The ACLK_BUS_ROOT is typically using CPLL as parent clock and running at
> 500 MHz out of reset when CPLL is running at 1.5 GHz.
>
> The parent and rate of ACLK_BUS_ROOT is changed to use GPLL and to run
> at 237 MHz during clock driver probe. However, the clock rate is
> hardcoded to be reported as 375 MHz.
>
> Change to explicitly use CPLL as parent and set the rate to 375 MHz, to
> match the reported rate and closer match how the Linux configures the
> clock.
>
For those wondering, it is statically configured to 375MHz in the Linux
kernel via the assigned-clock-rates property in
arch/arm64/boot/dts/rockchip/rk3588-base.dtsi for the clock controller.
> Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
> ---
> drivers/clk/rockchip/clk_rk3588.c | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/clk/rockchip/clk_rk3588.c b/drivers/clk/rockchip/clk_rk3588.c
> index d03ca9c4ac8d..c48743d8296f 100644
> --- a/drivers/clk/rockchip/clk_rk3588.c
> +++ b/drivers/clk/rockchip/clk_rk3588.c
> @@ -1921,11 +1921,11 @@ static void rk3588_clk_init(struct rk3588_clk_priv *priv)
> {
> int ret, div;
>
> - div = DIV_ROUND_UP(GPLL_HZ, 300 * MHz);
> + div = DIV_ROUND_UP(CPLL_HZ, 375 * MHz);
> rk_clrsetreg(&priv->cru->clksel_con[38],
> - ACLK_BUS_ROOT_SEL_MASK |
> - ACLK_BUS_ROOT_DIV_MASK,
> - div << ACLK_BUS_ROOT_DIV_SHIFT);
> + ACLK_BUS_ROOT_SEL_MASK | ACLK_BUS_ROOT_DIV_MASK,
> + (ACLK_BUS_ROOT_SEL_CPLL << ACLK_BUS_ROOT_SEL_SHIFT) |
> + (div - 1) << ACLK_BUS_ROOT_DIV_SHIFT);
>
This is a bug that you fix and haven't reported in the commit log. The
[4:0] bitfield stores div+1, so we need to remove 1 to div when writing
it to the register. I would say this warrants its own commit. Please split.
We switch to CPLL because GPLL is set to 1.188GHz which cannot derive
375MHz since there isn't a fractional divider for aclk_bus_root. CPLL is
set to 1.5GHz which cleanly divides by 4 to give 375MHz.
For the div -1 fix:
Fixes: 7a474df74023 ("clk: rockchip: Add rk3588 clk support")
For the GPLL->CPLL switch:
Fixes: 716ed2a8c0bb ("clk: rockchip: rk3588: add hardcoded assigned
clocks values")
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Thanks!
Quentin
next prev parent reply other threads:[~2026-08-07 15:45 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-30 14:12 [PATCH 00/15] rockchip: Miscellaneous RK35xx clock fixes Jonas Karlman
2026-07-30 14:12 ` [PATCH 01/15] clk: rockchip: pll: Fix double use of postdiv1 Jonas Karlman
2026-08-07 9:36 ` Quentin Schulz via U-Boot
2026-08-07 10:38 ` Jonas Karlman
2026-08-07 16:38 ` Quentin Schulz via U-Boot
2026-08-07 13:19 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 02/15] clk: rockchip: pll: Always write the dsmpd flag Jonas Karlman
2026-08-07 13:24 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 03/15] clk: rockchip: pll: Always write the k param Jonas Karlman
2026-08-07 13:29 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 04/15] clk: rockchip: pll: Use PLL_FIXED_MODE flag on rk3588/rk3576 plls Jonas Karlman
2026-08-07 14:09 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 05/15] clk: rockchip: pll: Limit special rk3588_pll handling to RK3588 Jonas Karlman
2026-08-07 14:30 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 06/15] clk: rockchip: rk3568: Fix trivial clock configuration errors Jonas Karlman
2026-08-07 14:46 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 07/15] clk: rockchip: rk3588: " Jonas Karlman
2026-08-07 15:07 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 08/15] clk: rockchip: rk3588: Fix possible divide by zero Jonas Karlman
2026-08-07 15:20 ` Quentin Schulz
2026-07-30 14:12 ` [PATCH 09/15] clk: rockchip: rk3588: Fix ACLK_BUS_ROOT rate set during probe Jonas Karlman
2026-08-07 15:44 ` Quentin Schulz [this message]
2026-07-30 14:12 ` [PATCH 10/15] clk: rockchip: rk3588: Use SPLL_HZ constant Jonas Karlman
2026-08-07 15:46 ` Quentin Schulz
2026-07-30 14:13 ` [PATCH 11/15] clk: rockchip: rk3576: Fix trivial clock configuration errors Jonas Karlman
2026-08-07 16:04 ` Quentin Schulz via U-Boot
2026-07-30 14:13 ` [PATCH 12/15] clk: rockchip: rk3528: " Jonas Karlman
2026-08-07 16:07 ` Quentin Schulz
2026-07-30 14:13 ` [PATCH 13/15] clk: rockchip: rk3506: " Jonas Karlman
2026-08-07 16:08 ` Quentin Schulz
2026-07-30 14:13 ` [PATCH 14/15] clk: rockchip: rk3568: Drop unused GRF syscon lookup Jonas Karlman
2026-08-07 16:16 ` Quentin Schulz
2026-07-30 14:13 ` [PATCH 15/15] clk: rockchip: rk3588: " Jonas Karlman
2026-08-07 16:19 ` Quentin Schulz
2026-08-08 13:37 ` [PATCH 00/15] rockchip: Miscellaneous RK35xx clock fixes Simon Glass
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c59fea96-266e-47bf-9d87-d008800b536c@cherry.de \
--to=quentin.schulz@cherry.de \
--cc=ilias.apalodimas@linaro.org \
--cc=jonas@kwiboo.se \
--cc=kever.yang@rock-chips.com \
--cc=lukma@denx.de \
--cc=sjg@chromium.org \
--cc=trini@konsulko.com \
--cc=u-boot@lists.u-boot-project.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.