[PATCH v10 0/4] AT91: replace broken TWI driver i2c-at91.c

[Nikolaus Voss <n.voss@weinmann.de>]

The old driver has two main deficencies:
i)  No repeated start (Sr) condiction is possible, this makes it unusable
    e.g. for most SMBus transfers.
ii) I/O was done with polling/busy waiting what caused over-/underruns
    even at light system loads and clock speeds.

The new driver overcomes these deficencies and in addition allows for
more than one TWI interface.

A remaining limitation is the fact, that only one repeated start is
possible (two concatenated messages). This limitation is imposed by
the hardware. However, this should not be a problem as all common
i2c-client communication does not rely on more than one repeated start.

Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Hubert Feurstein <h.feurstein@gmail.com>

v10: - applied fix for RXRDY overrun bug submitted by Hubert Feurstein
     - applied fix for calculating twi_clk
v9: - merge i2c-at91.c patches to single patch
    - rewrite cwgr reg after timeout
v8: - remove local include
    - remove cpu_is_rm9200() and put twi hw bug info in platform_device
    - use readl/writel_relaxed instead of __raw_readl/writel
v7: i)  fix bug if internal address > 1 byte
    ii) send stop when len == 1 (both reported by Carsten Behling)
v6: support for I2C_SMBUS_BLOCK_DATA transfers.
    Better use of clk_(un)prepare().
    More sensible transfer timeout.
v5: Another round of review comments from Ryan Mallon, Felipe Balbi
    and Russell King: convert twi clk to use .dev_id, cleanups
v4: Integrated more review comments from Ryan Mallon and Felipe Balbi:
    Moved register include file to local include, code cleanups
v3: Integrated review comments from Ryan Mallon and Felipe Balbi
v2: Fixed whitespace issue

Nikolaus Voss (4):
  drivers/i2c/busses/i2c-at91.c: remove broken driver
  Replace clk_lookup.con_id with clk_lookup.dev_id entries for twi clk
  drivers/i2c/busses/i2c-at91.c: add new driver
  G45 TWI: remove open drain setting for twi function gpios

 arch/arm/mach-at91/at91cap9.c              |    1 +
 arch/arm/mach-at91/at91rm9200.c            |    1 +
 arch/arm/mach-at91/at91rm9200_devices.c    |    9 +
 arch/arm/mach-at91/at91sam9260.c           |    1 +
 arch/arm/mach-at91/at91sam9261.c           |    1 +
 arch/arm/mach-at91/at91sam9263.c           |    1 +
 arch/arm/mach-at91/at91sam9g45.c           |    2 +
 arch/arm/mach-at91/at91sam9g45_devices.c   |    6 -
 arch/arm/mach-at91/at91sam9rl.c            |    2 +
 arch/arm/mach-at91/include/mach/at91_twi.h |   68 ----
 drivers/i2c/busses/Kconfig                 |   11 +-
 drivers/i2c/busses/i2c-at91.c              |  579 ++++++++++++++++++----------
 12 files changed, 393 insertions(+), 289 deletions(-)
 delete mode 100644 arch/arm/mach-at91/include/mach/at91_twi.h

-- 
1.7.5.4