From: Leonard Crestez <leonard.crestez@nxp.com>
To: MyungJoo Ham <myungjoo.ham@samsung.com>,
Kyungmin Park <kyungmin.park@samsung.com>,
Will Deacon <will@kernel.org>, Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>,
Jacky Bai <ping.bai@nxp.com>, Anson Huang <Anson.Huang@nxp.com>,
Abel Vesa <abel.vesa@nxp.com>,
Dong Aisheng <aisheng.dong@nxp.com>,
Viresh Kumar <viresh.kumar@linaro.org>,
Georgi Djakov <georgi.djakov@linaro.org>,
Alexandre Bailon <abailon@baylibre.com>,
Chanwoo Choi <cw00.choi@samsung.com>,
Mark Rutland <mark.rutland@arm.com>, Frank Li <Frank.li@nxp.com>,
Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>,
NXP Linux Team <linux-imx@nxp.com>,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [RFCv2 0/3] PM / devfreq: Add imx driver
Date: Wed, 24 Jul 2019 15:38:43 +0300 [thread overview]
Message-ID: <cover.1563971855.git.leonard.crestez@nxp.com> (raw)
This series attempts to add devfreq support for imx8mm, covering dynamic
scaling of internal buses and dram.
Actual scaling is performed through the clk framework: The NOC and main
NICs are driven by composite clks and a new 'imx8m-dram' clk is used for
scaling dram using firmware calls.
Frequency target is set via "clk_set_min_rate", this allows an unrelated
subsystem (for example interconnect) to also request minimum rates as a
form for proactive scaling.
The dram controller (DDRC) has a performance monitoring block attached
for which a perf driver already exists. Instead of reimplementing that
as devfreq-events the perf in-kernel API is used.
Changes since v2:
* Solve review comments
* Add yaml binding doc
* Add perf event support
Link to v2: https://patchwork.kernel.org/patch/11021571/
DRAM frequency switching through clk framework is here:
* https://patchwork.kernel.org/patch/11049429/
That part might not be accepted in clk and it might have to be moved to
devfreq also.
Leonard Crestez (3):
dt-bindings: devfreq: Add initial bindings for i.MX
PM / devfreq: Add imx driver
PM / devfreq: Add imx perf event support
.../devicetree/bindings/devfreq/imx.yaml | 59 ++++
drivers/devfreq/Kconfig | 10 +
drivers/devfreq/Makefile | 1 +
drivers/devfreq/imx-devfreq.c | 278 ++++++++++++++++++
4 files changed, 348 insertions(+)
create mode 100644 Documentation/devicetree/bindings/devfreq/imx.yaml
create mode 100644 drivers/devfreq/imx-devfreq.c
--
2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Leonard Crestez <leonard.crestez@nxp.com>
To: MyungJoo Ham <myungjoo.ham@samsung.com>,
Kyungmin Park <kyungmin.park@samsung.com>,
Will Deacon <will@kernel.org>, Stephen Boyd <sboyd@kernel.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>,
Mark Rutland <mark.rutland@arm.com>,
Fabio Estevam <festevam@gmail.com>,
Sascha Hauer <s.hauer@pengutronix.de>,
Jacky Bai <ping.bai@nxp.com>, Anson Huang <Anson.Huang@nxp.com>,
linux-pm@vger.kernel.org, Viresh Kumar <viresh.kumar@linaro.org>,
Michael Turquette <mturquette@baylibre.com>,
Frank Li <Frank.li@nxp.com>, NXP Linux Team <linux-imx@nxp.com>,
linux-kernel@vger.kernel.org,
Chanwoo Choi <cw00.choi@samsung.com>,
devicetree@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
Alexandre Bailon <abailon@baylibre.com>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Shawn Guo <shawnguo@kernel.org>,
Georgi Djakov <georgi.djakov@linaro.org>,
linux-arm-kernel@lists.infradead.org,
Abel Vesa <abel.vesa@nxp.com>
Subject: [RFCv2 0/3] PM / devfreq: Add imx driver
Date: Wed, 24 Jul 2019 15:38:43 +0300 [thread overview]
Message-ID: <cover.1563971855.git.leonard.crestez@nxp.com> (raw)
This series attempts to add devfreq support for imx8mm, covering dynamic
scaling of internal buses and dram.
Actual scaling is performed through the clk framework: The NOC and main
NICs are driven by composite clks and a new 'imx8m-dram' clk is used for
scaling dram using firmware calls.
Frequency target is set via "clk_set_min_rate", this allows an unrelated
subsystem (for example interconnect) to also request minimum rates as a
form for proactive scaling.
The dram controller (DDRC) has a performance monitoring block attached
for which a perf driver already exists. Instead of reimplementing that
as devfreq-events the perf in-kernel API is used.
Changes since v2:
* Solve review comments
* Add yaml binding doc
* Add perf event support
Link to v2: https://patchwork.kernel.org/patch/11021571/
DRAM frequency switching through clk framework is here:
* https://patchwork.kernel.org/patch/11049429/
That part might not be accepted in clk and it might have to be moved to
devfreq also.
Leonard Crestez (3):
dt-bindings: devfreq: Add initial bindings for i.MX
PM / devfreq: Add imx driver
PM / devfreq: Add imx perf event support
.../devicetree/bindings/devfreq/imx.yaml | 59 ++++
drivers/devfreq/Kconfig | 10 +
drivers/devfreq/Makefile | 1 +
drivers/devfreq/imx-devfreq.c | 278 ++++++++++++++++++
4 files changed, 348 insertions(+)
create mode 100644 Documentation/devicetree/bindings/devfreq/imx.yaml
create mode 100644 drivers/devfreq/imx-devfreq.c
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2019-07-24 12:38 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-24 12:38 Leonard Crestez [this message]
2019-07-24 12:38 ` [RFCv2 0/3] PM / devfreq: Add imx driver Leonard Crestez
2019-07-24 12:38 ` [RFCv3 1/3] dt-bindings: devfreq: Add initial bindings for i.MX Leonard Crestez
2019-07-24 12:38 ` Leonard Crestez
2019-07-25 14:23 ` Chanwoo Choi
2019-07-25 14:23 ` Chanwoo Choi
2019-07-25 14:23 ` Chanwoo Choi
2019-07-24 12:38 ` [RFCv3 2/3] PM / devfreq: Add imx driver Leonard Crestez
2019-07-24 12:38 ` Leonard Crestez
2019-07-24 12:38 ` [RFCv3 3/3] PM / devfreq: Add imx perf event support Leonard Crestez
2019-07-24 12:38 ` Leonard Crestez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1563971855.git.leonard.crestez@nxp.com \
--to=leonard.crestez@nxp.com \
--cc=Anson.Huang@nxp.com \
--cc=Frank.li@nxp.com \
--cc=abailon@baylibre.com \
--cc=abel.vesa@nxp.com \
--cc=aisheng.dong@nxp.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=georgi.djakov@linaro.org \
--cc=kernel@pengutronix.de \
--cc=kyungmin.park@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=myungjoo.ham@samsung.com \
--cc=ping.bai@nxp.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
--cc=viresh.kumar@linaro.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.