All of lore.kernel.org
 help / color / mirror / Atom feed
From: Ahmed Naseef <naseefkm@gmail.com>
To: linux-gpio@vger.kernel.org
Cc: Ahmed Naseef <naseefkm@gmail.com>,
	Benjamin Larsson <benjamin.larsson@genexis.eu>,
	Christian Marangi <ansuelsmth@gmail.com>,
	Conor Dooley <conor+dt@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Linus Walleij <linusw@kernel.org>,
	Lorenzo Bianconi <lorenzo@kernel.org>,
	Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>,
	Rob Herring <robh@kernel.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-mediatek@lists.infradead.org
Subject: [PATCH 0/3] pinctrl: airoha: add EcoNet EN7528 pin controller support
Date: Sun,  9 Aug 2026 12:04:57 +0400	[thread overview]
Message-ID: <cover.1786262697.git.naseefkm@gmail.com> (raw)

The EcoNet EN7528 is a MIPS SoC that uses the same pin controller and GPIO
IP as the Airoha SoCs, so it reuses the shared driver code introduced by
the split into per-SoC drivers. Its register layout differs from every
existing variant though: all IOMUX mode bits live in a single CHIP SCU
register plus a few spill-over bits in IOMUX Control 3, EJTAG has its own
enable register, and every pin configuration register is at a different
offset than on EN7523.

It also differs in a way the shared code did not model: only GPIO0-GPIO15
are wired to the interrupt controller, while the driver assumed all
AIROHA_NUM_PINS GPIOs could raise an interrupt. Patch 1 adds a
num_irq_pins field to the per-SoC match data to describe that, bounds the
interrupt callbacks and handler with it, and feeds it to gpiolib through
gpio_irq_chip::init_valid_mask so gpiod_to_irq() fails up front for a pin
that can never be an interrupt source. All existing SoCs pass
AIROHA_NUM_PINS and are unaffected.

Patch 2 documents the binding, patch 3 adds the driver.

The series is based on linux-pinctrl/for-next, as it depends on the
per-SoC driver split and on the CHIP SCU lookup by "airoha,chip-scu"
phandle that landed there.

Tested on a DASAN H660GM-A (EN7528, Airtel), booting OpenWrt.

Ahmed Naseef (2):
  pinctrl: airoha: limit GPIO interrupts to interrupt-capable pins
  dt-bindings: pinctrl: Add EcoNet EN7528 pin controller

Benjamin Larsson (1):
  pinctrl: airoha: add support of en7528 SoC

 .../pinctrl/econet,en7528-pinctrl.yaml        |  190 +++
 drivers/pinctrl/airoha/Kconfig                |   15 +-
 drivers/pinctrl/airoha/Makefile               |    1 +
 drivers/pinctrl/airoha/airoha-common.h        |    3 +
 drivers/pinctrl/airoha/pinctrl-airoha.c       |   33 +-
 drivers/pinctrl/airoha/pinctrl-an7563.c       |    1 +
 drivers/pinctrl/airoha/pinctrl-an7581.c       |    1 +
 drivers/pinctrl/airoha/pinctrl-an7583.c       |    1 +
 drivers/pinctrl/airoha/pinctrl-en7523.c       |    1 +
 drivers/pinctrl/airoha/pinctrl-en7528.c       | 1204 +++++++++++++++++
 10 files changed, 1443 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/econet,en7528-pinctrl.yaml
 create mode 100644 drivers/pinctrl/airoha/pinctrl-en7528.c


base-commit: 87e787e591a82b9b324aa0968795b256f789d287
-- 
2.34.1


             reply	other threads:[~2026-08-09  8:05 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-08-09  8:04 Ahmed Naseef [this message]
2026-08-09  8:04 ` [PATCH 1/3] pinctrl: airoha: limit GPIO interrupts to interrupt-capable pins Ahmed Naseef
2026-08-09  8:18   ` sashiko-bot
2026-08-09  8:04 ` [PATCH 2/3] dt-bindings: pinctrl: Add EcoNet EN7528 pin controller Ahmed Naseef
2026-08-09  8:15   ` sashiko-bot
2026-08-09  8:05 ` [PATCH 3/3] pinctrl: airoha: add support of en7528 SoC Ahmed Naseef
2026-08-10  7:23 ` [PATCH 0/3] pinctrl: airoha: add EcoNet EN7528 pin controller support Linus Walleij
2026-08-10  7:27   ` Christian Marangi (Ansuel)
2026-08-11  6:17     ` Linus Walleij

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=cover.1786262697.git.naseefkm@gmail.com \
    --to=naseefkm@gmail.com \
    --cc=ansuelsmth@gmail.com \
    --cc=benjamin.larsson@genexis.eu \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linusw@kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=lorenzo@kernel.org \
    --cc=mikhail.kshevetskiy@iopsys.eu \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.