From: gokulsri@codeaurora.org
To: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: agross@kernel.org, bjorn.andersson@linaro.org,
robh+dt@kernel.org, sboyd@codeaurora.org,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, sricharan@codeaurora.org
Subject: Re: [PATCH v2 3/3] arm64: dts: Enabled MHI device over PCIe
Date: Wed, 30 Sep 2020 16:34:21 +0530 [thread overview]
Message-ID: <d3b10e0842192eb7016ebc447e148378@codeaurora.org> (raw)
In-Reply-To: <20200806102623.GB2406@Mani-XPS-13-9360>
On 2020-08-06 15:56, Manivannan Sadhasivam wrote:
> On Thu, Aug 06, 2020 at 03:02:12PM +0530, Gokul Sriram Palanisamy
> wrote:
>> Enabled MHI device support over PCIe and added memory
>> reservation required for MHI enabled QCN9000 PCIe card.
>>
>
> There is no DT support exist for MHI as of now, so this is not going to
> work.
>
> Thanks,
> Mani
>
Hi Mani,
The dt entries are to be used by the ath11k driver. Will remove
mhi,max-channels and mhi,timeout
and post a new revision.
Thanks,
Gokul
>> Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
>> ---
>> arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi | 58
>> ++++++++++++++++++++++++++++++
>> arch/arm64/boot/dts/qcom/ipq8074.dtsi | 8 +++++
>> 2 files changed, 66 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
>> b/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
>> index 0827055..d201a7b 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
>> @@ -24,6 +24,22 @@
>> device_type = "memory";
>> reg = <0x0 0x40000000 0x0 0x20000000>;
>> };
>> +
>> + reserved-memory {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + qcn9000_pcie0: memory@50f00000 {
>> + no-map;
>> + reg = <0x0 0x50f00000 0x0 0x03700000>;
>> + };
>> +
>> + qcn9000_pcie1: memory@54600000 {
>> + no-map;
>> + reg = <0x0 0x54600000 0x0 0x03700000>;
>> + };
>> + };
>> };
>>
>> &blsp1_spi1 {
>> @@ -74,3 +90,45 @@
>> nand-bus-width = <8>;
>> };
>> };
>> +
>> +&pcie0_rp {
>> + status = "ok";
>> +
>> + mhi_0: qcom,mhi@0 {
>> + reg = <0 0 0 0 0 >;
>> + qrtr_instance_id = <0x20>;
>> + #address-cells = <0x2>;
>> + #size-cells = <0x2>;
>> +
>> + base-addr = <0x50f00000>;
>> + qcom,caldb-addr = <0x53E00000>;
>> + qrtr_node_id = <0x27>;
>> + mhi,max-channels = <30>;
>> + mhi,timeout = <10000>;
>> +
>> + pcie0_mhi: pcie0_mhi {
>> + status = "ok";
>> + };
>> + };
>> +};
>> +
>> +&pcie1_rp {
>> + status = "ok";
>> +
>> + mhi_1: qcom,mhi@1 {
>> + reg = <0 0 0 0 0 >;
>> + qrtr_instance_id = <0x21>;
>> + #address-cells = <0x2>;
>> + #size-cells = <0x2>;
>> +
>> + base-addr = <0x54600000>;
>> + qcom,caldb-addr = <0x57500000>;
>> + qrtr_node_id = <0x28>;
>> + mhi,max-channels = <30>;
>> + mhi,timeout = <10000>;
>> +
>> + pcie1_mhi: pcie1_mhi {
>> + status = "ok";
>> + };
>> + };
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> index b651345..eef47c1 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> @@ -709,6 +709,10 @@
>> "ahb",
>> "axi_m_sticky";
>> status = "disabled";
>> +
>> + pcie1_rp: pcie1_rp {
>> + reg = <0 0 0 0 0>;
>> + };
>> };
>>
>> pcie0: pci@20000000 {
>> @@ -779,6 +783,10 @@
>> "axi_m_sticky",
>> "axi_s_sticky";
>> status = "disabled";
>> +
>> + pcie0_rp: pcie0_rp {
>> + reg = <0 0 0 0 0>;
>> + };
>> };
>>
>> tcsr_q6: syscon@1945000 {
>> --
>> 2.7.4
>>
prev parent reply other threads:[~2020-09-30 11:05 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-06 9:32 [PATCH v2 0/3] Add board support for HK10 board variants Gokul Sriram Palanisamy
2020-08-06 9:32 ` [PATCH v2 1/3] dt-bindings: qcom: Add ipq8074 bindings Gokul Sriram Palanisamy
2020-08-12 20:07 ` Rob Herring
2020-08-06 9:32 ` [PATCH v2 2/3] arm64: dts: Add board support for HK10 Gokul Sriram Palanisamy
2020-08-06 9:32 ` [PATCH v2 3/3] arm64: dts: Enabled MHI device over PCIe Gokul Sriram Palanisamy
2020-08-06 10:26 ` Manivannan Sadhasivam
2020-09-30 11:04 ` gokulsri [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=d3b10e0842192eb7016ebc447e148378@codeaurora.org \
--to=gokulsri@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=sricharan@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.