From: Greg Felix <gregfelixlkml@gmail.com>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-kernel@vger.kernel.org
Subject: Re: PROBLEM: ICH7 SATA drive not detected.
Date: Fri, 25 Feb 2005 18:05:13 -0700 [thread overview]
Message-ID: <e16ac85e050225170545ceceb7@mail.gmail.com> (raw)
In-Reply-To: <e16ac85e05022517024beb5b38@mail.gmail.com>
Jeff,
I forgot: in dmesg I see the following:
ata_piix: probe of 0000:00:1f.2 failed with error -5
Greg Felix
On Fri, 25 Feb 2005 18:02:59 -0700, Greg Felix <gregfelixlkml@gmail.com> wrote:
> > Jeff Garzik wrote:
> > See REPORTING-BUGS for the sort of information you should provide. This
> > is a "it doesn't work" report without much more info.
> >
> > I would suggest doing a "modprobe ata_piix" or "modprobe ahci"
> > (depending on ICH7 mode and hardware) and see what happens in 'dmesg'.
> >
> > Jeff
>
> Let me try and do this right.
> Here's the bug report:
>
> ICH7 SATA drive not detected.
>
> I have two new OEM machines that are both ICH7 chipsets. Both
> machines give the same vendor and device PCI ids for their storage
> controllers. 8086:27df and 8086:27c0. One of the machines' disks is
> being detected correctly (sda). The other one is not. I have tried
> modprobing both ata_piix and ahci with negative results. It is very
> new hardware. There is also a broadcom NIC that is not being
> detected, but I don't NEED that to work. (I'll file a bug if requested
> of me.)
>
> keywords: piix, ICH7, SATA, ata_piix, ahci
>
> I'm running 2.6.11-rc5 in a custom distribution in a ram disk from a
> pxe boot. I also have a USB memory device inserted into the machine
> being detected as sda for the reports below.
>
> Here's the output of ver_linux:
> Linux (none) 2.6.11-rc5 #1 Fri Feb 25 12:31:16 MST 2005 i686 unknown
> unknown GNU/Linux
>
> Gnu C 18:
> mount 2.12p
> module-init-tools 3.1
> reiserfsprogs line
> reiser4progs line
> Dynamic linker (ldd) 2.3.4
> Procps 3.2.3
> Net-tools 1.60
> Kbd 81:
> Sh-utils 5.2.1
> Modules Loaded
>
> /proc/cpuinfo reads:
> processor : 0
> vendor_id : GenuineIntel
> cpu family : 15
> model : 4
> model name : Genuine Intel(R) CPU 3.20GHz
> stepping : 1
> cpu MHz : 3193.334
> cache size : 1024 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 5
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
> mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
> pni monitor ds_cpl cid xtpr
> bogomips : 6307.84
>
> /proc/modules reads:
> ahci 5508 0 - Live 0xe0086000
> nls_cp437 4608 1 - Live 0xe0083000
> msdos 5248 1 - Live 0xe0018000
> fat 27548 1 msdos, Live 0xe008e000
> nls_base 4352 2 nls_cp437,fat, Live 0xe001b000
> sd_mod 11152 2 - Live 0xe0038000
> usb_storage 25216 1 - Live 0xe0065000
> usbhid 21376 0 - Live 0xe0047000
> edd 6496 0 - Live 0xe0007000
> ide_cd 29956 0 - Live 0xe007a000
> cdrom 30112 1 ide_cd, Live 0xe0071000
> ide_disk 11520 0 - Live 0xe0034000
> ata_piix 4228 0 - Live 0xe0031000
> libata 28804 2 ahci,ata_piix, Live 0xe003e000
> piix 6404 0 [permanent], Live 0xe0002000
> generic 2432 0 [permanent], Live 0xe0005000
> ide_core 85676 5 usb_storage,ide_cd,ide_disk,piix,generic, Live 0xe004f000
> ehci_hcd 21000 0 - Live 0xe0011000
> uhci_hcd 22416 0 - Live 0xe000a000
> usbcore 72696 5 usb_storage,usbhid,ehci_hcd,uhci_hcd, Live 0xe001e000
>
> /proc/ioports reads:
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-0043 : timer0
> 0050-0053 : timer1
> 0060-006f : keyboard
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 01f0-01f7 : ide0
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 0cf8-0cff : PCI conf1
> 1000-101f : 0000:00:1d.0
> 1000-101f : uhci_hcd
> 1020-103f : 0000:00:1d.1
> 1020-103f : uhci_hcd
> 1040-105f : 0000:00:1d.2
> 1040-105f : uhci_hcd
> 1060-107f : 0000:00:1d.3
> 1060-107f : uhci_hcd
> 10a0-10af : 0000:00:1f.1
> 10a0-10a7 : ide0
> 10a8-10af : ide1
> 10b0-10bf : 0000:00:1f.2
> 10c0-10c7 : 0000:00:02.0
> 10d8-10df : 0000:00:1f.2
> 10e0-10e7 : 0000:00:1f.2
> 10f0-10f3 : 0000:00:1f.2
> 10f4-10f7 : 0000:00:1f.2
>
> /proc/iomem reads:
> 00000000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000ca800-000cb7ff : Adapter ROM
> 000cb800-000ccfff : Adapter ROM
> 000f0000-000fffff : System ROM
> 00100000-1f7e27ff : System RAM
> 00100000-00210717 : Kernel code
> 00210718-0024c37f : Kernel data
> 1f7e2800-1fffffff : reserved
> d0000000-dfffffff : 0000:00:02.0
> e0400000-e047ffff : 0000:00:02.0
> e0480000-e04bffff : 0000:00:02.0
> e04c0000-e04c3fff : 0000:00:1b.0
> e04c4000-e04c43ff : 0000:00:1d.7
> e04c4000-e04c43ff : ehci_hcd
> e04c4400-e04c47ff : 0000:00:1f.2
> e0500000-e07fffff : PCI Bus #3f
> e0500000-e050ffff : 0000:3f:00.0
> f0000000-f3ffffff : reserved
> fec00000-ffffffff : reserved
>
> lspci -vvv gives:
> 00:00.0 Class 0600: 8086:2770
> Subsystem: 103c:3011
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Capabilities: [e0] Vendor Specific Information
>
> 00:02.0 Class 0300: 8086:2772
> Subsystem: 103c:3011
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=512K]
> Region 1: I/O ports at 10c0 [size=8]
> Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
> Region 3: Memory at e0480000 (32-bit, non-prefetchable) [size=256K]
> Capabilities: [90] Message Signalled Interrupts: 64bit-
> Queue=0/0 Enable-
> Address: 00000000 Data: 0000
> Capabilities: [d0] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1b.0 Class 0403: 8086:27d8
> Subsystem: 103c:3011
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e04c0000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [60] Message Signalled Interrupts: 64bit+
> Queue=0/0 Enable-
> Address: 0000000000000000 Data: 0000
> Capabilities: [70] Express Unknown type IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
> Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
> Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
> Link: Latency L0s <64ns, L1 <1us
> Link: ASPM Disabled CommClk- ExtSynch-
> Link: Speed unknown, Width x0
>
> 00:1c.0 Class 0604: 8086:27d0
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [40] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
> Device: Latency L0s unlimited, L1 unlimited
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
> Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
> Link: Latency L0s <1us, L1 <4us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x1
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
> Slot: Number 2, PowerLimit 10.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Unknown, PwrInd Unknown, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [80] Message Signalled Interrupts: 64bit-
> Queue=0/0 Enable-
> Address: 00000000 Data: 0000
> Capabilities: [90] #0d [0000]
> Capabilities: [a0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1c.1 Class 0604: 8086:27d2
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Bus: primary=00, secondary=3f, subordinate=3f, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: e0500000-e07fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [40] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
> Device: Latency L0s unlimited, L1 unlimited
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
> Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
> Link: Latency L0s <256ns, L1 <4us
> Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
> Link: Speed 2.5Gb/s, Width x1
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
> Slot: Number 3, PowerLimit 10.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Unknown, PwrInd Unknown, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [80] Message Signalled Interrupts: 64bit-
> Queue=0/0 Enable-
> Address: 00000000 Data: 0000
> Capabilities: [90] #0d [0000]
> Capabilities: [a0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1d.0 Class 0c03: 8086:27c8
> Subsystem: 103c:3011
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 5
> Region 4: I/O ports at 1000 [size=32]
>
> 00:1d.1 Class 0c03: 8086:27c9
> Subsystem: 103c:3011
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 10
> Region 4: I/O ports at 1020 [size=32]
>
> 00:1d.2 Class 0c03: 8086:27ca
> Subsystem: 103c:3011
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 11
> Region 4: I/O ports at 1040 [size=32]
>
> 00:1d.3 Class 0c03: 8086:27cb
> Subsystem: 103c:3011
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 11
> Region 4: I/O ports at 1060 [size=32]
>
> 00:1d.7 Class 0c03: 8086:27cc (prog-if 20)
> Subsystem: 103c:3011
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at e04c4000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Debug port
>
> 00:1e.0 Class 0604: 8086:244e (rev e0) (prog-if 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [50] #0d [0000]
>
> 00:1f.0 Class 0601: 8086:27b0
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [e0] Vendor Specific Information
>
> 00:1f.1 Class 0101: 8086:27df (prog-if 8a [Master SecP PriP])
> Subsystem: 103c:3011
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 5
> Region 0: I/O ports at <ignored>
> Region 1: I/O ports at <ignored>
> Region 2: I/O ports at <ignored>
> Region 3: I/O ports at <ignored>
> Region 4: I/O ports at 10a0 [size=16]
>
> 00:1f.2 Class 0101: 8086:27c0 (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: 103c:3011
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 5
> Region 0: I/O ports at 10d8 [size=8]
> Region 1: I/O ports at 10f0 [size=4]
> Region 2: I/O ports at 10e0 [size=8]
> Region 3: I/O ports at 10f4 [size=4]
> Region 4: I/O ports at 10b0 [size=16]
> Region 5: Memory at e04c4400 (32-bit, non-prefetchable)
> [disabled] [size=1K]
> Capabilities: [80] Message Signalled Interrupts: 64bit-
> Queue=0/2 Enable-
> Address: 00000000 Data: 0000
> Capabilities: [70] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 3f:00.0 Class 0200: 14e4:1600
> Subsystem: 103c:3011
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=64K]
> Capabilities: [48] Power Management version 2
>
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
> Capabilities: [58] Message Signalled Interrupts: 64bit+
> Queue=0/3 Enable-
> Address: 0068d809080002c0 Data: 0000
> Capabilities: [d0] Express Endpoint IRQ 0
> Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag+
> Device: Latency L0s <4us, L1 unlimited
> Device: AtnBtn- AtnInd- PwrInd-
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
> Link: Latency L0s <4us, L1 <64us
> Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
> Link: Speed 2.5Gb/s, Width x1
>
> /proc/devices reads:
> Character devices:
> 1 mem
> 4 /dev/vc/0
> 4 tty
> 5 /dev/tty
> 5 /dev/console
> 7 vcs
> 10 misc
> 13 input
> 180 usb
>
> Block devices:
> 1 ramdisk
> 3 ide0
> 8 sd
> 65 sd
> 66 sd
> 67 sd
> 68 sd
> 69 sd
> 70 sd
> 71 sd
> 128 sd
> 129 sd
> 130 sd
> 131 sd
> 132 sd
> 133 sd
> 134 sd
> 135 sd
>
next prev parent reply other threads:[~2005-02-26 1:13 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-02-25 23:36 Intel ICH7 SATA support question for ATA_PIIX Greg Felix
2005-02-26 0:00 ` Jeff Garzik
2005-02-26 1:02 ` PROBLEM: ICH7 SATA drive not detected Greg Felix
2005-02-26 1:05 ` Greg Felix [this message]
2005-02-26 4:35 ` Jeff Garzik
2005-02-28 17:22 ` Greg Felix
2005-03-30 19:33 ` Jeff Garzik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e16ac85e050225170545ceceb7@mail.gmail.com \
--to=gregfelixlkml@gmail.com \
--cc=jgarzik@pobox.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.