From: Stefan Schweizer <genstef@gentoo.org>
To: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Subject: Re: suspend
Date: Thu, 03 Apr 2008 09:42:00 +0200 [thread overview]
Message-ID: <ft21pb$oc3$1@ger.gmane.org> (raw)
In-Reply-To: 200804030932.27993.oliver@neukum.org
Oliver Neukum wrote:
> Please load the appletouch module with the parameter "debug=1" and
> post dmesg of a suspend/resume and the chvt thing.
I found out the appletouch issue was already discused here:
http://lkml.org/lkml/2007/3/28/172
Unfortunately there seems to be no workaround and X-input still has more
issues than it solves..
Attached is the dmesg excerpt
Best regards,
Stefan
usbcore: deregistering interface driver appletouch
input: appletouch disconnected
appletouch: Geyser mode initialized.
input: appletouch
as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.1/input/input19
usbcore: registered new interface driver appletouch
PM: Syncing filesystems ... done.
Stopping fuse filesystems.
Freezing user space processes ... (elapsed 0.00 seconds) <6>done.
Stopping normal filesystems.
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) <6>done.
ACPI: Preparing to enter system sleep state S3
Suspending console(s)
sd 2:0:1:0: [sda] Synchronizing SCSI cache
sd 2:0:1:0: [sda] Stopping disk
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:02:00.0 disabled
sky2 eth0: disabling interface
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3995.35 BogoMIPS
(lpj=1997676)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000
0000c1a9 00000000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9
00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2500 @ 2.00GHz stepping 08
CPU1 is up
Switched to high resolution mode on CPU 1
PM: Writing back config space on device 0000:00:02.0 at offset f (was 100,
writing 10a)
PM: Writing back config space on device 0000:00:02.0 at offset 7 (was 0,
writing 90400000)
PM: Writing back config space on device 0000:00:02.0 at offset 6 (was 8,
writing 80000008)
PM: Writing back config space on device 0000:00:02.0 at offset 5 (was 1,
writing 20f1)
PM: Writing back config space on device 0000:00:02.0 at offset 4 (was 0,
writing 90380000)
PM: Writing back config space on device 0000:00:02.0 at offset 1 (was
900000, writing 900007)
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:02.0 to 64
PM: Writing back config space on device 0000:00:02.1 at offset 4 (was 0,
writing 90300000)
PM: Writing back config space on device 0000:00:02.1 at offset 1 (was
900000, writing 900007)
PM: Writing back config space on device 0000:00:07.0 at offset f (was 100,
writing 10a)
PM: Writing back config space on device 0000:00:07.0 at offset 4 (was 0,
writing 90444000)
PM: Writing back config space on device 0000:00:07.0 at offset 1 (was
b00000, writing b00002)
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4,
writing 90440004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0,
writing 40)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was
100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
PM: Writing back config space on device 0000:00:1c.0 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:00:1c.0 at offset 9 (was 10001,
writing 50015001)
PM: Writing back config space on device 0000:00:1c.0 at offset 8 (was 0,
writing 90209020)
PM: Writing back config space on device 0000:00:1c.0 at offset 7 (was
20000000, writing 20001010)
PM: Writing back config space on device 0000:00:1c.0 at offset 6 (was 0,
writing 10100)
PM: Writing back config space on device 0000:00:1c.0 at offset 3 (was
810000, writing 810040)
PM: Writing back config space on device 0000:00:1c.0 at offset 1 (was
100000, writing 100007)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PM: Writing back config space on device 0000:00:1c.1 at offset f (was 200,
writing 20a)
PM: Writing back config space on device 0000:00:1c.1 at offset 9 (was 10001,
writing 1fff1)
PM: Writing back config space on device 0000:00:1c.1 at offset 8 (was 0,
writing 90109010)
PM: Writing back config space on device 0000:00:1c.1 at offset 7 (was
20000000, writing f0)
PM: Writing back config space on device 0000:00:1c.1 at offset 6 (was 0,
writing 20200)
PM: Writing back config space on device 0000:00:1c.1 at offset 3 (was
810000, writing 810040)
PM: Writing back config space on device 0000:00:1c.1 at offset 1 (was
100000, writing 100007)
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Enabling device 0000:00:1d.0 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
PM: Writing back config space on device 0000:00:1d.0 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:00:1d.0 at offset 8 (was 1,
writing 20a1)
usb usb1: root hub lost power or was reset
PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200,
writing 20b)
PM: Writing back config space on device 0000:00:1d.1 at offset 8 (was 1,
writing 2081)
usb usb2: root hub lost power or was reset
PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300,
writing 30b)
PM: Writing back config space on device 0000:00:1d.2 at offset 8 (was 1,
writing 2061)
usb usb3: root hub lost power or was reset
PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.3 to 64
PM: Writing back config space on device 0000:00:1d.3 at offset f (was 400,
writing 40a)
PM: Writing back config space on device 0000:00:1d.3 at offset 8 (was 1,
writing 2041)
usb usb4: root hub lost power or was reset
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0,
writing 90445400)
PM: Writing back config space on device 0000:00:1e.0 at offset 9 (was 10001,
writing 1fff1)
PM: Writing back config space on device 0000:00:1e.0 at offset 8 (was 0,
writing 90009000)
PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was
22800000, writing 228000f0)
PM: Writing back config space on device 0000:00:1e.0 at offset 6 (was 0,
writing 20030300)
PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was
100000, writing 100007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:00:1f.1 at offset 1 (was
2800001, writing 2800005)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.1 to 64
PM: Writing back config space on device 0000:00:1f.2 at offset f (was 200,
writing 20b)
PM: Writing back config space on device 0000:00:1f.2 at offset 8 (was 1,
writing 2021)
PM: Writing back config space on device 0000:00:1f.2 at offset 1 (was
2b00002, writing 2b00007)
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
PM: Writing back config space on device 0000:00:1f.3 at offset f (was 200,
writing 20b)
PM: Writing back config space on device 0000:01:00.0 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:01:00.0 at offset c (was 0,
writing fffe0000)
PM: Writing back config space on device 0000:01:00.0 at offset 6 (was 1,
writing 1001)
PM: Writing back config space on device 0000:01:00.0 at offset 4 (was 4,
writing 90200004)
PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0,
writing 40)
PM: Writing back config space on device 0000:01:00.0 at offset 1 (was
40100000, writing 100007)
sky2 eth0: enabling interface
PM: Writing back config space on device 0000:02:00.0 at offset f (was 100,
writing 10b)
PM: Writing back config space on device 0000:02:00.0 at offset 4 (was 4,
writing 90100004)
PM: Writing back config space on device 0000:02:00.0 at offset 3 (was 0,
writing 40)
PM: Writing back config space on device 0000:02:00.0 at offset 1 (was
100000, writing 100007)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
PM: Writing back config space on device 0000:03:03.0 at offset f (was
180c0100, writing 180c010b)
PM: Writing back config space on device 0000:03:03.0 at offset 4 (was 0,
writing 90000000)
PM: Writing back config space on device 0000:03:03.0 at offset 3 (was 0,
writing f810)
PM: Writing back config space on device 0000:03:03.0 at offset 1 (was
2900000, writing 2900216)
sd 2:0:1:0: [sda] Starting disk
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:44:00:00:00:a0 filtered out
ata3.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out
ata3.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out
ata3.01: configured for UDMA/100
sd 2:0:1:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sda] Write Protect is off
sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
ata1.00: configured for UDMA/66
restoring control 00000000-0000-0000-0000-000000000101/0/2
restoring control 00000000-0000-0000-0000-000000000101/3/7
restoring control 00000000-0000-0000-0000-000000000101/5/9
applesmc: received a shock interrupt
applesmc: cannot setup irq handler
applesmc: accelerometer successfully initialized.
Restarting all filesystems ...
Restarting tasks ... <6>usb 1-1: USB disconnect, address 6
done.
usb 1-1: new low speed USB device using uhci_hcd and address 8
usb 1-1: configuration #1 chosen from 1 choice
input: HID 0461:4d03
as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input20
input: USB HID v1.10 Mouse [HID 0461:4d03] on usb-0000:00:1d.0-1
usb 1-2: USB disconnect, address 7
input: appletouch disconnected
usb 1-2: new full speed USB device using uhci_hcd and address 9
usb 1-2: configuration #1 chosen from 1 choice
input: Apple Computer Apple Internal Keyboard / Trackpad
as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/input/input21
input: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard /
Trackpad] on usb-0000:00:1d.0-2
appletouch: Geyser mode initialized.
input: appletouch
as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.1/input/input22
appletouch: incomplete data package (first byte: 2, length: 4).
input: Apple Computer Apple Internal Keyboard / Trackpad
as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.2/input/input23
input: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard /
Trackpad] on usb-0000:00:1d.0-2
usb 3-2: USB disconnect, address 3
usb 3-2: new full speed USB device using uhci_hcd and address 4
usb 3-2: configuration #1 chosen from 1 choice
hiddev0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on
usb-0000:00:1d.2-2
usb 4-1: USB disconnect, address 3
usb 4-1: new full speed USB device using uhci_hcd and address 4
usb 4-1: configuration #1 chosen from 1 choice
input: HID 05ac:1000
as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.0/input/input24
input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1d.3-1
input: HID 05ac:1000
as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.1/input/input25
input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1d.3-1
next prev parent reply other threads:[~2008-04-03 7:42 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-02 6:31 suspend Justin Mattock
2008-04-02 12:19 ` suspend Rafael J. Wysocki
2008-04-02 15:53 ` suspend Justin Mattock
2008-04-02 17:39 ` suspend Rafael J. Wysocki
2008-04-02 19:18 ` suspend Justin Mattock
2008-04-02 22:21 ` suspend Rafael J. Wysocki
2008-04-03 0:00 ` suspend Justin Mattock
2008-04-03 0:18 ` suspend Tejun Heo
2008-04-03 0:44 ` suspend Justin Mattock
2008-04-03 1:01 ` suspend Tejun Heo
2008-04-03 1:16 ` suspend Justin Mattock
2008-04-02 23:09 ` suspend Stefan Schweizer
2008-04-02 23:55 ` suspend Rafael J. Wysocki
2008-04-03 7:32 ` suspend Oliver Neukum
2008-04-03 7:42 ` Stefan Schweizer [this message]
2008-04-03 8:02 ` suspend Oliver Neukum
2008-04-03 8:29 ` suspend Oliver Neukum
2008-04-03 8:53 ` suspend Stefan Schweizer
[not found] ` <e79639220804030153q46fa82c7jb79bedbe88b30df7-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2008-04-03 10:31 ` suspend Oliver Neukum
[not found] ` <200804031231.19193.oliver-GvhC2dPhHPQdnm+yROfE0A@public.gmane.org>
2008-04-03 15:44 ` suspend Stefan Schweizer
2008-04-03 20:42 ` suspend Oliver Neukum
[not found] ` <200804032242.36493.oliver-GvhC2dPhHPQdnm+yROfE0A@public.gmane.org>
2008-04-03 21:41 ` suspend Alan Stern
2008-04-03 22:06 ` suspend Stefan Schweizer
2008-04-04 8:59 ` suspend Oliver Neukum
2008-04-04 9:20 ` suspend Stefan Schweizer
[not found] ` <e79639220804040220g560e94b4l418724ff1653780d-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2008-04-04 11:36 ` suspend Oliver Neukum
2008-04-04 22:40 ` suspend Stefan Schweizer
2008-04-05 8:00 ` suspend Oliver Neukum
2008-04-05 9:15 ` suspend Stefan Schweizer
[not found] ` <e79639220804050215j42829de7iab99b51e85683a53-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2008-04-05 9:12 ` suspend Oliver Neukum
2008-04-05 14:13 ` suspend Alan Stern
2008-04-03 10:58 ` suspend Oliver Neukum
2008-04-03 14:14 ` suspend Stefan Schweizer
2008-04-03 21:07 ` suspend Oliver Neukum
2008-04-03 23:14 ` suspend Justin Mattock
[not found] <CAM2dokvEdG5P5dso8+3vh7urX1FCFx4p+g-TiBH62+pMfuDKqA@mail.gmail.com>
2020-05-06 18:21 ` Fwd: Suspend Jaime Perez
2020-05-06 18:47 ` Suspend Kaneda, Erik
-- strict thread matches above, loose matches on Subject: below --
2008-03-31 19:10 suspend Justin Mattock
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='ft21pb$oc3$1@ger.gmane.org' \
--to=genstef@gentoo.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.