From: feldmaus <feldmann_markus@gmx.de>
To: linux-wireless@vger.kernel.org
Subject: Re: Do not get BCM4303 to work
Date: Fri, 26 Sep 2008 23:07:23 +0200 [thread overview]
Message-ID: <gbjipv$cgd$1@ger.gmane.org> (raw)
In-Reply-To: <48C5777B.9070106@lwfinger.net>
Larry Finger schrieb:
> feldmaus wrote:
>> Hi All,
>>
>> i do not get my Wlan Card with BCM4303 Chip to work.
>>
>> I am not sure whether this Card is active, because <dmesg> show me,
>> [ 409.752921] b43legacy-phy0: Radio hardware status changed to DISA=
BLED
>=20
> Your card can receive, but not transmit due to a problem with the rfk=
ill=20
> switch handling in b43legacy. I'm working on this problem with a Ubun=
tu=20
> user, and will post patches as soon as the problem is fixed.
>=20
> Larry
Hi Larry,
i thought it would be helpful to post my Messages. :-)
If not ignore this Message.:-)
I am using the NetworkManager Applet to show and connect to Wlan Networ=
ks.
My wireless Button shines blue when my Linux System starts.
However after i login onto myGnome Desktop and after some time the=20
NetworkManager Applet shows me my Wireless Network.
dmesg says,
=2E..
[ 22.024553] Broadcom 43xx-legacy driver loaded [ Features: PLRID,=20
=46irmware-ID: FW10 ]
=2E..
[ 43.384052] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[ 40.776050] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 40.892896] b43legacy-phy0 debug: Chip initialized
[ 40.893291] b43legacy-phy0 debug: 30-bit DMA initialized
[ 40.893422] Registered led device: b43legacy-phy0:tx
[ 40.901752] Registered led device: b43legacy-phy0:rx
[ 40.909982] Registered led device: b43legacy-phy0:radio
[ 40.918152] b43legacy-phy0 debug: Wireless interface started
[ 40.918159] b43legacy-phy0 debug: Adding Interface type 2
[ 40.936417] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 41.300046] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
=2E..
Then i try to connect to this Network by press on my listed Network in
the NetworkManager Applet. Then he connects to the Network. Der Network=
=20
Balken zeigt einen Verbindungsstatus an von 0%.
dmesg says,
[ 530.437247] b43legacy-phy0 debug: Removing Interface type 2
[ 530.446006] b43legacy-phy0 debug: Wireless interface stopped
[ 530.446142] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 530.446190] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
1/64
[ 530.446245] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 530.452052] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 530.460038] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 530.468036] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 530.476042] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
2/128
[ 530.485144] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 530.492042] b43legacy-phy0 debug: Radio initialized
[ 530.492058] b43legacy-phy0 debug: Radio initialized
[ 530.506575] input: b43legacy-phy0 as /class/input/input10
[ 530.672048] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 530.824472] b43legacy-phy0 debug: Chip initialized
[ 530.824862] b43legacy-phy0 debug: 30-bit DMA initialized
[ 530.824993] Registered led device: b43legacy-phy0:tx
[ 530.825031] Registered led device: b43legacy-phy0:rx
[ 530.825069] Registered led device: b43legacy-phy0:radio
[ 530.825102] b43legacy-phy0 debug: Wireless interface started
[ 530.825109] b43legacy-phy0 debug: Adding Interface type 3
[ 530.846071] wlan0: Trigger new scan to find an IBSS to join
[ 531.520050] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 531.520431] b43legacy-phy0 debug: Radio initialized
[ 531.584041] b43legacy-phy0: Radio turned on by software
[ 531.584055] b43legacy-phy0: The hardware RF-kill button still turns=20
the radio physically off. Press the button to turn it on.
[ 533.652045] wlan0: Trigger new scan to find an IBSS to join
[ 536.428046] wlan0: Trigger new scan to find an IBSS to join
[ 539.204045] wlan0: Trigger new scan to find an IBSS to join
[ 539.980089] wlan0: Creating new IBSS network, BSSID 96:d6:b6:75:12:4=
a
[ 539.980130] wlan0: Configured IBSS beacon template
[ 540.928032] wlan0: no IPv6 routers present
[ 569.980046] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 600.756051] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 612.720029] wlan0: no IPv6 routers present
[ 725.457997] wlan0: deauthenticate(reason=3D3)
[ 726.477007] b43legacy-phy0 debug: Removing Interface type 3
[ 726.492057] b43legacy-phy0 debug: Wireless interface stopped
[ 726.492226] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 726.492272] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
1/64
[ 726.492329] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 726.500165] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 726.508046] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 726.516038] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 726.524214] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
4/128
[ 726.532042] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 726.540054] b43legacy-phy0 debug: Radio initialized
[ 726.540069] b43legacy-phy0 debug: Radio initialized
[ 726.633096] input: b43legacy-phy0 as /class/input/input11
[ 726.796037] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 726.896786] b43legacy-phy0 debug: Chip initialized
[ 726.897036] b43legacy-phy0 debug: 30-bit DMA initialized
[ 726.897117] Registered led device: b43legacy-phy0:tx
[ 726.897133] Registered led device: b43legacy-phy0:rx
[ 726.897149] Registered led device: b43legacy-phy0:radio
[ 726.897172] b43legacy-phy0 debug: Wireless interface started
[ 726.897175] b43legacy-phy0 debug: Adding Interface type 3
[ 727.644031] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 727.924601] b43legacy-phy0 debug: Removing Interface type 3
[ 727.930047] b43legacy-phy0 debug: Wireless interface stopped
[ 727.930129] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 727.930159] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[ 727.930203] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 727.936037] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 727.944029] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 727.952032] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 727.960033] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
2/128
[ 727.968034] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 727.976034] b43legacy-phy0 debug: Radio initialized
[ 727.976043] b43legacy-phy0 debug: Radio initialized
[ 727.983509] input: b43legacy-phy0 as /class/input/input12
[ 728.152040] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 728.252442] b43legacy-phy0 debug: Chip initialized
[ 728.252729] b43legacy-phy0 debug: 30-bit DMA initialized
[ 728.252819] Registered led device: b43legacy-phy0:tx
[ 728.252839] Registered led device: b43legacy-phy0:rx
[ 728.252858] Registered led device: b43legacy-phy0:radio
[ 728.252883] b43legacy-phy0 debug: Wireless interface started
[ 728.252887] b43legacy-phy0 debug: Adding Interface type 2
[ 728.280215] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 728.344731] b43legacy-phy0 debug: Removing Interface type 2
[ 728.349895] b43legacy-phy0 debug: Wireless interface stopped
[ 728.349978] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
0/64
[ 728.350008] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[ 728.350046] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 728.356050] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 728.364030] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 728.372028] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 728.380028] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
0/128
[ 728.388030] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 728.396033] b43legacy-phy0 debug: Radio initialized
[ 728.396042] b43legacy-phy0 debug: Radio initialized
[ 728.403446] input: b43legacy-phy0 as /class/input/input13
[ 728.572043] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 728.672542] b43legacy-phy0 debug: Chip initialized
[ 728.672827] b43legacy-phy0 debug: 30-bit DMA initialized
[ 728.672916] Registered led device: b43legacy-phy0:tx
[ 728.672937] Registered led device: b43legacy-phy0:rx
[ 728.672956] Registered led device: b43legacy-phy0:radio
[ 728.672981] b43legacy-phy0 debug: Wireless interface started
[ 728.672985] b43legacy-phy0 debug: Adding Interface type 3
[ 728.693355] wlan0: Trigger new scan to find an IBSS to join
[ 729.416034] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 729.416179] b43legacy-phy0 debug: Radio initialized
[ 729.500029] b43legacy-phy0: Radio turned on by software
[ 729.500037] b43legacy-phy0: The hardware RF-kill button still turns=20
the radio physically off. Press the button to turn it on.
[ 731.500116] wlan0: Trigger new scan to find an IBSS to join
[ 734.276046] wlan0: Trigger new scan to find an IBSS to join
[ 737.052043] wlan0: Trigger new scan to find an IBSS to join
[ 737.828087] wlan0: Creating new IBSS network, BSSID f2:00:ad:b6:b3:3=
a
[ 737.828128] wlan0: Configured IBSS beacon template
[ 738.884029] wlan0: no IPv6 routers present
[ 767.828045] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 798.604045] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 810.584030] wlan0: no IPv6 routers present
[ 994.892048] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1025.668044] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
ifconfig says,
wlan0 Link encap:Ethernet Hardware Adresse 00:90:4b:97:34:73
inet Adresse:169.254.78.197 Bcast:169.254.255.255=20
Maske:255.255.0.0
inet6-Adresse: fe80::290:4bff:fe97:3473/64=20
G=FCltigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:179 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenl=E4nge:1000
RX bytes:0 (0.0 B) TX bytes:32937 (32.1 KiB)
As you can see, some Packets would transmitted over my Wireless Card.
iwconfig says,
wlan0 IEEE 802.11 ESSID:"kleopatra"
Mode:Ad-Hoc Frequency:2.412 GHz Cell: 76:0D:1D:B5:B7:73
Tx-Power=3D27 dBm
Retry min limit:7 RTS thr:off Fragment thr=3D2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
However i can not print to my Wlan Printer and the status in the Networ=
k=20
Manager shows 0%.
Then i pressed my wireless Button, and dmesg says
[ 1056.444034] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1111.004046] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1141.780078] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1172.555792] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1193.449106] phy0: Adding new IBSS station 00:30:6e:d2:4a:99 (dev=3Dw=
lan0)
[ 1212.996048] wlan0: expiring inactive STA 00:30:6e:d2:4a:99
[ 1212.996285] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1243.772044] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1274.548043] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1320.929652] wlan0: deauthenticate(reason=3D3)
[ 1321.952124] b43legacy-phy0 debug: Removing Interface type 3
[ 1321.964039] b43legacy-phy0 debug: Wireless interface stopped
[ 1321.964127] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 1321.964160] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
1/64
[ 1321.964198] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 1321.972035] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 1321.980027] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 1321.988031] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 1321.996030] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
4/128
[ 1322.004028] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 1322.012026] b43legacy-phy0 debug: Radio initialized
[ 1322.012035] b43legacy-phy0 debug: Radio initialized
[ 1322.093411] input: b43legacy-phy0 as /class/input/input14
[ 1322.256079] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 1322.356791] b43legacy-phy0 debug: Chip initialized
[ 1322.357047] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1322.357127] Registered led device: b43legacy-phy0:tx
[ 1322.357144] Registered led device: b43legacy-phy0:rx
[ 1322.357160] Registered led device: b43legacy-phy0:radio
[ 1322.357184] b43legacy-phy0 debug: Wireless interface started
[ 1322.357188] b43legacy-phy0 debug: Adding Interface type 3
[ 1323.104036] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 1323.384592] b43legacy-phy0 debug: Removing Interface type 3
[ 1323.396041] b43legacy-phy0 debug: Wireless interface stopped
[ 1323.396150] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 1323.396183] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[ 1323.396226] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 1323.404039] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 1323.412026] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 1323.420026] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 1323.428031] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
2/128
[ 1323.436034] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 1323.444032] b43legacy-phy0 debug: Radio initialized
[ 1323.444041] b43legacy-phy0 debug: Radio initialized
[ 1323.454511] input: b43legacy-phy0 as /class/input/input15
[ 1323.620042] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 1323.720624] b43legacy-phy0 debug: Chip initialized
[ 1323.720911] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1323.721002] Registered led device: b43legacy-phy0:tx
[ 1323.721024] Registered led device: b43legacy-phy0:rx
[ 1323.721043] Registered led device: b43legacy-phy0:radio
[ 1323.721069] b43legacy-phy0 debug: Wireless interface started
[ 1323.721073] b43legacy-phy0 debug: Adding Interface type 2
[ 1323.748106] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1323.811666] b43legacy-phy0 debug: Removing Interface type 2
[ 1323.817608] b43legacy-phy0 debug: Wireless interface stopped
[ 1323.817690] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
0/64
[ 1323.817722] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[ 1323.817761] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 1323.824041] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 1323.832037] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 1323.840033] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 1323.848029] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
0/128
[ 1323.856035] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 1323.864839] b43legacy-phy0 debug: Radio initialized
[ 1323.864849] b43legacy-phy0 debug: Radio initialized
[ 1323.872375] input: b43legacy-phy0 as /class/input/input16
[ 1324.040043] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 1324.140544] b43legacy-phy0 debug: Chip initialized
[ 1324.140835] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1324.140927] Registered led device: b43legacy-phy0:tx
[ 1324.140948] Registered led device: b43legacy-phy0:rx
[ 1324.140967] Registered led device: b43legacy-phy0:radio
[ 1324.140992] b43legacy-phy0 debug: Wireless interface started
[ 1324.140996] b43legacy-phy0 debug: Adding Interface type 3
[ 1324.161293] wlan0: Trigger new scan to find an IBSS to join
[ 1324.884035] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 1324.884253] b43legacy-phy0 debug: Radio initialized
[ 1324.968031] b43legacy-phy0: Radio turned on by software
[ 1324.968040] b43legacy-phy0: The hardware RF-kill button still turns=20
the radio physically off. Press the button to turn it on.
[ 1326.968047] wlan0: Trigger new scan to find an IBSS to join
[ 1329.744048] wlan0: Trigger new scan to find an IBSS to join
[ 1332.520047] wlan0: Trigger new scan to find an IBSS to join
[ 1333.296087] wlan0: Creating new IBSS network, BSSID 76:0d:1d:b5:b7:7=
3
[ 1333.296126] wlan0: Configured IBSS beacon template
[ 1334.644033] wlan0: no IPv6 routers present
[ 1363.296044] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1394.072046] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1405.964030] wlan0: no IPv6 routers present
[ 1517.772022] phy0: Adding new IBSS station 00:30:6e:d2:4a:99 (dev=3Dw=
lan0)
[ 1517.772037] wlan0: expiring inactive STA 00:30:6e:d2:4a:99
[ 1517.772037] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1574.332043] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1582.205006] phy0: Adding new IBSS station 00:30:6e:d2:4a:99 (dev=3Dw=
lan0)
[ 1605.112054] wlan0: expiring inactive STA 00:30:6e:d2:4a:99
[ 1605.128043] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1635.908058] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1666.684045] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
The Mac Adress "00:30:6e:d2:4a:99" is from my wireless Printer
Regards Markus
--
To unsubscribe from this list: send the line "unsubscribe linux-wireles=
s" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2008-09-26 21:05 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-09-08 6:15 Do not get BCM4303 to work feldmaus
2008-09-08 7:34 ` maximilian attems
2008-09-08 19:05 ` Larry Finger
2008-09-12 23:02 ` feldmaus
2008-09-13 0:30 ` Larry Finger
2008-09-26 16:32 ` feldmaus
2008-09-26 17:27 ` Larry Finger
2008-09-26 21:07 ` feldmaus [this message]
2008-09-26 23:40 ` Larry Finger
2009-01-03 18:37 ` feldmaus
2009-01-03 18:49 ` feldmaus
2009-01-03 19:00 ` feldmaus
2009-01-03 19:05 ` Larry Finger
2009-01-03 19:39 ` feldmaus
2009-01-04 11:34 ` feldmaus
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='gbjipv$cgd$1@ger.gmane.org' \
--to=feldmann_markus@gmx.de \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.