From: Vince <stuff@hagenhuegel.de>
To: linux-raid@vger.kernel.org
Subject: Re: Raid5 drive fail during grow and no backup
Date: Thu, 6 Nov 2014 17:12:37 +0000 (UTC) [thread overview]
Message-ID: <loom.20141106T175806-337@post.gmane.org> (raw)
In-Reply-To: loom.20141105T200200-434@post.gmane.org
Hi Phil,
> This is a problem you haven't solved yet, I think. The raid array
> should have fixed this bad sector for you without kicking the drive out.
> The scenario is common with "green" drives and/or consumer-grade
> drives in general.
i investigated some time and now i am a bit confused.
All my 5 WD Red drives have ERC enables (7sec)
The kernel timeout is set to 30sec (/sys/block/sdb/device/timeout)
on all devices.
Unfortunately i haven't any backup of the dmesg output, but i can remeber i
got something like:
"failed command: READ FPDMA QUEUED status: { DRDY ERR } error: { UNC }".
This shows up several times until it ends with showing me the sector which
causes the problem.
My raid is still up, but as you mentioned i would like some kind of self
repair if a sector is unreadable instead throwing the disk out of the array.
Here is the samrtctl of one drive that fails.
Do you have any idea if i missing some settings etc?
smartctl -x /dev/sdd
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red (AF)
Device Model: WDC WD30EFRX-68AX9N0
Serial Number: WD-WMC1T2041480
LU WWN Device Id: 5 0014ee 058d836a6
Firmware Version: 80.00A80
User Capacity: 3.000.592.982.016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Nov 6 18:10:11 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (42000) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1625
3 Spin_Up_Time POS--K 176 173 021 - 6175
4 Start_Stop_Count -O--CK 099 099 000 - 1290
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 084 084 000 - 11786
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 177
192 Power-Off_Retract_Count -O--CK 200 200 000 - 50
193 Load_Cycle_Count -O--CK 200 200 000 - 1239
194 Temperature_Celsius -O---K 121 102 000 - 29
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xbd has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 93 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 6807 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6807 [14] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.798 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.798 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 16:03:04.798 SET FEATURES [Set
transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.797 IDENTIFY DEVICE
Error 6806 [13] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 08 16:03:04.798 SET FEATURES [Set
transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.797 IDENTIFY DEVICE
35 00 00 04 00 00 01 13 7f 4c 00 e0 08 16:03:04.797 WRITE DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
Error 6805 [12] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.797 IDENTIFY DEVICE
35 00 00 04 00 00 01 13 7f 4c 00 e0 08 16:03:04.797 WRITE DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.796 IDENTIFY DEVICE
Error 6804 [11] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 04 00 00 01 13 7f 4c 00 e0 00 Device Fault; Error: ABRT 1024
sectors at LBA = 0x1137f4c00 = 4622076928
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 04 00 00 01 13 7f 4c 00 e0 08 16:03:04.797 WRITE DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.796 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES [Set
transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES
[Reserved for Serial ATA]
Error 6803 [10] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.797 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.796 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES [Set
transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.795 IDENTIFY DEVICE
Error 6802 [9] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES [Set
transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.795 IDENTIFY DEVICE
35 00 00 04 00 00 01 13 7f 4c 00 e0 08 16:03:04.795 WRITE DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.795 SET FEATURES
[Reserved for Serial ATA]
Error 6801 [8] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.796 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.795 IDENTIFY DEVICE
35 00 00 04 00 00 01 13 7f 4c 00 e0 08 16:03:04.795 WRITE DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.795 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.795 IDENTIFY DEVICE
Error 6800 [7] occurred at disk power-on lifetime: 11653 hours (485 days +
13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 04 00 00 01 13 7f 4c 00 e0 00 Device Fault; Error: ABRT 1024
sectors at LBA = 0x1137f4c00 = 4622076928
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 04 00 00 01 13 7f 4c 00 e0 08 16:03:04.795 WRITE DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.795 SET FEATURES
[Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 16:03:04.795 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 16:03:04.794 SET FEATURES [Set
transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 16:03:04.794 SET FEATURES
[Reserved for Serial ATA]
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 11770 -
# 2 Short offline Completed without error 00% 11757 -
# 3 Short offline Completed without error 00% 11746 -
# 4 Extended offline Completed without error 00% 11729 -
# 5 Extended offline Completed without error 00% 11698 -
# 6 Extended offline Aborted by host 90% 11677 -
# 7 Short offline Completed without error 00% 11654 -
# 8 Short offline Completed without error 00% 11565 -
# 9 Short offline Completed: read failure 70% 11557 9
#10 Short offline Completed: read failure 70% 11557 9
#11 Extended offline Completed: read failure 90% 11556 9
#12 Short offline Completed without error 00% 1367 -
#13 Short offline Completed without error 00% 1346 -
#14 Extended offline Completed without error 00% 1327 -
#15 Short offline Completed without error 00% 1295 -
#16 Short offline Completed without error 00% 1271 -
#17 Short offline Completed without error 00% 1247 -
#18 Short offline Completed without error 00% 1223 -
3 of 3 failed self-tests are outdated by newer successful extended offline
self-test # 4
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 29 Celsius
Power Cycle Min/Max Temperature: 22/35 Celsius
Lifetime Min/Max Temperature: 15/49 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (158)
Index Estimated Time Temperature Celsius
159 2014-11-06 10:13 29 **********
... ..( 20 skipped). .. **********
180 2014-11-06 10:34 29 **********
181 2014-11-06 10:35 31 ************
... ..(128 skipped). .. ************
310 2014-11-06 12:44 31 ************
311 2014-11-06 12:45 30 ***********
... ..( 70 skipped). .. ***********
382 2014-11-06 13:56 30 ***********
383 2014-11-06 13:57 31 ************
... ..( 82 skipped). .. ************
466 2014-11-06 15:20 31 ************
467 2014-11-06 15:21 30 ***********
... ..( 32 skipped). .. ***********
22 2014-11-06 15:54 30 ***********
23 2014-11-06 15:55 29 **********
... ..( 49 skipped). .. **********
73 2014-11-06 16:45 29 **********
74 2014-11-06 16:46 30 ***********
... ..( 2 skipped). .. ***********
77 2014-11-06 16:49 30 ***********
78 2014-11-06 16:50 29 **********
... ..( 23 skipped). .. **********
102 2014-11-06 17:14 29 **********
103 2014-11-06 17:15 30 ***********
... ..( 9 skipped). .. ***********
113 2014-11-06 17:25 30 ***********
114 2014-11-06 17:26 29 **********
... ..( 43 skipped). .. **********
158 2014-11-06 18:10 29 **********
SCT Error Recovery Control:
Read: 70 (7,0 seconds)
Write: 70 (7,0 seconds)
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 15 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 15 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 363301 Vendor specific
next prev parent reply other threads:[~2014-11-06 17:12 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-31 13:34 Raid5 drive fail during grow and no backup Vince
2014-11-02 3:22 ` Phil Turmel
2014-11-03 14:45 ` Vince
2014-11-04 16:17 ` Phil Turmel
2014-11-05 19:03 ` Vince
2014-11-06 17:12 ` Vince [this message]
2014-11-07 13:36 ` Phil Turmel
2014-11-07 16:07 ` P. Gautschi
2014-11-07 16:06 ` P. Gautschi
2014-11-08 3:36 ` Phil Turmel
2014-11-10 3:20 ` Jason Keltz
2014-12-04 19:29 ` Phillip Susi
2014-12-04 20:02 ` Phil Turmel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=loom.20141106T175806-337@post.gmane.org \
--to=stuff@hagenhuegel.de \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.