From: Peter Osterlund <petero2@telia.com>
To: Greg KH <greg@kroah.com>
Cc: Pierre ROUSSELET <pierre.rousselet@wanadoo.fr>,
Johannes Erdfelt <johannes@erdfelt.com>,
linux-kernel@vger.kernel.org
Subject: Re: 2.5.25 uhci-hcd very bad
Date: 18 Jul 2002 13:18:42 +0200 [thread overview]
Message-ID: <m2bs95e12l.fsf@best.localdomain> (raw)
In-Reply-To: <20020718060551.GB12626@kroah.com>
Greg KH <greg@kroah.com> writes:
> On Thu, Jul 18, 2002 at 08:35:37AM +0200, Pierre ROUSSELET wrote:
> > The driver is made of a kernel module speedtch.o (built outside of the
> > tree) and of userspace modem firmware loader and management daemon
> > speedmgt.
>
> I'd suggest asking the authors of the driver about this.
I also get the "very bad" message when booting 2.5.25 and 2.5.26, even
if no usb devices are connected. From dmesg:
Freeing unused kernel memory: 200k freed
Adding 104824k swap on /dev/hda3. Priority:-1 extents:1
usb.c: registered new driver usbfs
usb.c: registered new driver hub
uhci-hcd.c: USB Universal Host Controller Interface driver v2.0
PCI: Assigned IRQ 10 for device 00:07.2
hcd-pci.c: uhci-hcd @ 00:07.2, Intel Corp. 82371AB PIIX4 USB
hcd-pci.c: irq 10, io base 0000f300
hcd.c: new USB bus registered, assigned bus number 1
uhci-hcd.c: detected 2 ports
hcd.c: 00:07.2 root hub device address 1
usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1
Product: Intel Corp. 82371AB PIIX4 USB
Manufacturer: Linux 2.5.26-packet uhci-hcd
SerialNumber: 00:07.2
hub.c: USB hub found at /
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c10ce460
usb.c: kusbd: /sbin/hotplug add 1
uhci-hcd.c: f300: suspend_hc
uhci-hcd.c: f300: wakeup_hc
uhci-hcd.c: f300: suspend_hc
uhci-hcd.c: f300: wakeup_hc
... (usually repeated about 50 times)
uhci-hcd.c: f300: suspend_hc
uhci-hcd.c: f300: host controller halted. very bad
uhci-hcd.c: f300: wakeup_hc
This happens both with preemtible and non-preemtible kernels. I can
still use a Freecom usb cdrw drive though, so maybe this is not a
problem, even though the message indicates that it is.
I also have a performance problem with the uhci-hcd driver. When
writing data to a CDRW in packet writing mode, usb_stor_freecom_reset
is called quite often, see logs below. This happens in both 2.5.25 and
2.5.26. I tested with the usb-uhci-hcd driver in 2.5.25 (edited the
Makefile) just to rule out kernel changes and other usb changes, but
that driver didn't have this problem. I saw one or two freecom reset
messages though, so it's possible that the new driver just makes an
old problem much more frequent.
pengo:/home/petero# tail -f -n 10000 /var/log/debug | egrep 'Command |reset'
...
Jul 18 12:57:04 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:05 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:05 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:05 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:05 pengo kernel: freecom reset called
Jul 18 12:57:05 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:06 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:06 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:06 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:07 pengo kernel: freecom reset called
Jul 18 12:57:07 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:08 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:08 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:08 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:08 pengo kernel: freecom reset called
Jul 18 12:57:08 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:10 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:10 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:10 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:10 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:11 pengo kernel: freecom reset called
Jul 18 12:57:11 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:13 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:13 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:13 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:13 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:15 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:15 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:16 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:16 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:16 pengo kernel: freecom reset called
Jul 18 12:57:16 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:17 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:20 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:20 pengo kernel: freecom reset called
Jul 18 12:57:20 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:20 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:21 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:57:21 pengo kernel: freecom reset called
...
>From /var/log/debug:
Jul 18 12:18:11 pengo kernel: usb-storage: queuecommand() called
Jul 18 12:18:11 pengo kernel: usb-storage: *** thread sleeping.
Jul 18 12:18:11 pengo kernel: usb-storage: *** thread awakened.
Jul 18 12:18:11 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:18:11 pengo kernel: usb-storage: 2a 00 00 00 1b e0 00 00 20 00 00 00
Jul 18 12:18:11 pengo kernel: usb-storage: Freecom TRANSPORT STARTED
Jul 18 12:18:11 pengo kernel: usb-storage: 00000000: 2a 00 00 00 1b e0 00 00 - 20 00 00 00 - *....... ...
Jul 18 12:18:11 pengo kernel: usb-storage: foo Status result 0 4
Jul 18 12:18:11 pengo kernel: usb-storage: 00000000: 4a 00 00 f8 - J...
Jul 18 12:18:11 pengo kernel: usb-storage: Device indicates that it has 63488 bytes available
Jul 18 12:18:11 pengo kernel: usb-storage: SCSI requested 65536
Jul 18 12:18:11 pengo kernel: usb-storage: Write data Freecom! (c=65536)
Jul 18 12:18:11 pengo kernel: usb-storage: Done issuing write request: 0 64
Jul 18 12:18:11 pengo kernel: usb-storage: Start of write
Jul 18 12:18:11 pengo kernel: usb-storage: transfer_amount: 65536 and total_transferred: 0
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): transfer complete
Jul 18 12:18:11 pengo kernel: usb-storage: transfer_amount: 65536 and total_transferred: 4096
... [cut]
Jul 18 12:18:11 pengo kernel: usb-storage: transfer_amount: 65536 and total_transferred: 61440
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): transfer complete
Jul 18 12:18:11 pengo kernel: usb-storage: freecom_writedata done!
Jul 18 12:18:11 pengo kernel: usb-storage: FCM: Waiting for status
Jul 18 12:18:11 pengo kernel: usb-storage: operation failed
Jul 18 12:18:11 pengo kernel: usb-storage: -- transport indicates command failure
Jul 18 12:18:11 pengo kernel: usb-storage: Issuing auto-REQUEST_SENSE
Jul 18 12:18:11 pengo kernel: usb-storage: Freecom TRANSPORT STARTED
Jul 18 12:18:11 pengo kernel: usb-storage: 00000000: 03 00 00 00 12 00 00 00 - 20 00 00 00 - ........ ...
Jul 18 12:18:11 pengo kernel: usb-storage: foo Status result 0 4
Jul 18 12:18:11 pengo kernel: usb-storage: 00000000: 52 03 ff ff - R...
Jul 18 12:18:11 pengo kernel: usb-storage: Device indicates that it has 65535 bytes available
Jul 18 12:18:11 pengo kernel: usb-storage: SCSI requested 18
Jul 18 12:18:11 pengo kernel: usb-storage: Truncating request to match buffer length: 18
Jul 18 12:18:11 pengo kernel: usb-storage: SCSI wants data, drive doesn't have any
Jul 18 12:18:11 pengo kernel: usb-storage: -- auto-sense failure
Jul 18 12:18:11 pengo kernel: freecom reset called
Jul 18 12:18:11 pengo kernel: usb-storage: scsi cmd done, result=0x70000
Jul 18 12:18:11 pengo kernel: usb-storage: queuecommand() called
Jul 18 12:18:11 pengo kernel: usb-storage: *** thread sleeping.
Jul 18 12:18:11 pengo kernel: usb-storage: *** thread awakened.
Jul 18 12:18:11 pengo kernel: usb-storage: Command WRITE_10 (10 bytes)
Jul 18 12:18:11 pengo kernel: usb-storage: 2a 00 00 00 1b e0 00 00 20 00 00 00
Jul 18 12:18:11 pengo kernel: usb-storage: Freecom TRANSPORT STARTED
Jul 18 12:18:11 pengo kernel: usb-storage: 00000000: 2a 00 00 00 1b e0 00 00 - 20 00 00 00 - *....... ...
Jul 18 12:18:11 pengo kernel: usb-storage: foo Status result 0 4
Jul 18 12:18:11 pengo kernel: usb-storage: 00000000: 4a 00 00 f8 - J...
Jul 18 12:18:11 pengo kernel: usb-storage: Device indicates that it has 63488 bytes available
Jul 18 12:18:11 pengo kernel: usb-storage: SCSI requested 65536
Jul 18 12:18:11 pengo kernel: usb-storage: Write data Freecom! (c=65536)
Jul 18 12:18:11 pengo kernel: usb-storage: Done issuing write request: 0 64
Jul 18 12:18:11 pengo kernel: usb-storage: Start of write
Jul 18 12:18:11 pengo kernel: usb-storage: transfer_amount: 65536 and total_transferred: 0
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): transfer complete
Jul 18 12:18:11 pengo kernel: usb-storage: transfer_amount: 65536 and total_transferred: 4096
... [cut]
Jul 18 12:18:11 pengo kernel: usb-storage: transfer_amount: 65536 and total_transferred: 61440
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
Jul 18 12:18:11 pengo kernel: usb-storage: usb_stor_transfer_partial(): transfer complete
Jul 18 12:18:11 pengo kernel: usb-storage: freecom_writedata done!
Jul 18 12:18:11 pengo kernel: usb-storage: FCM: Waiting for status
Jul 18 12:18:12 pengo kernel: usb-storage: Transfer happy
Jul 18 12:18:12 pengo kernel: usb-storage: scsi cmd done, result=0x0
Jul 18 12:18:12 pengo kernel: usb-storage: *** thread sleeping.
--
Peter Osterlund - petero2@telia.com
http://w1.894.telia.com/~u89404340
next prev parent reply other threads:[~2002-07-18 11:19 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-07-13 20:14 2.5.25 uhci-hcd very bad Pierre Rousselet
2002-07-17 21:33 ` Greg KH
2002-07-18 6:35 ` Pierre ROUSSELET
2002-07-18 6:05 ` Greg KH
2002-07-18 7:36 ` Pierre ROUSSELET
2002-07-18 11:18 ` Peter Osterlund [this message]
2002-07-18 6:10 ` Duncan Sands
2002-07-18 7:37 ` Pierre ROUSSELET
2002-07-18 7:02 ` Duncan Sands
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=m2bs95e12l.fsf@best.localdomain \
--to=petero2@telia.com \
--cc=greg@kroah.com \
--cc=johannes@erdfelt.com \
--cc=linux-kernel@vger.kernel.org \
--cc=pierre.rousselet@wanadoo.fr \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.