From: David Wuertele <dave-gnus@bfnet.com>
To: linux-scsi@vger.kernel.org
Cc: linux-usb-users@lists.sourceforge.net
Subject: Re: Trying to troubleshoot ornery Phison usb-storage
Date: Fri, 14 Mar 2003 18:27:24 -0800 [thread overview]
Message-ID: <m37kb1jreb.fsf@bfnet.com> (raw)
In-Reply-To: 20030314175543.E32112@one-eyed-alien.net
Matt> Could you repeat this test with:
Matt> (a) max_scsi_luns spelled properly on the command line, and
Matt> (b) max_scsi_luns set to 0
D'oh!
Here we go... With max_scsi_luns set to 0, fdisk didn't even find a
device:
# dmesg -n 8
# fdisk /dev/scsi/host0/bus0/target0/lun0/disc
Unable to open /dev/scsi/host0/bus0/target0/lun0/disc
#
No errors were printed to console at all. (Since it is not as
interesting, I've appended the console output for this case to the end
of the email, after the max_scsi_luns=3 case).
Wit max_scsi_luns=3, I got identical results in the shell:
# dmesg -n 8
# fdisk /dev/scsi/host0/bus0/target0/lun0/disc
Unable to read /dev/scsi/host0/bus0/target0/lun0/disc
#
This time, there was some console output. I include the whole thing
here:
memsize environment variable not set: assuming 32MB
CPU revision is: 00018007
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Linux version 2.4.18_dev-xilleon_x220 (dave@vmrh73g.localdomain) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-99.1)) #24 Thu Mar 13 09:38:57 PST 2003
KGDB: Using serial line /dev/ttyS1 for session
Determined physical RAM map:
memory: 00080000 @ 00000000 (ROM data)
memory: 00080000 @ 00080000 (reserved)
memory: 01f00000 @ 00100000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: nfsroot=10.0.0.157:/nfsroot,rw,rsize=1024,wsize=1024 max_scsi_luns=3 hda=none hdb=none rw ip=10.0.1.3 console=ttyS0,115200,n,8,1
ide_setup: hda=none
ide_setup: hdb=none
Initializing IRQs
calculating r4koff... CPU frequency 598.42 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 598.01 BogoMIPS
MIPS CPU counter frequency is fixed at 299209896 Hz
Memory: 28456k/31744k available (2230k kernel code, 3288k reserved, 323k data, 4k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Autoconfig PCI channel 0x803804e8
Scanning bus 00, I/O 0x00002000:0x00010001, Mem 0x10000000:0x18000001
00:08.0 Class 0200: 10ec:8139 (rev 10)
I/O at 0x00002000 [size=0x100]
Mem at 0x10000000 [size=0x100]
00:14.0 Class 0480: 1002:4855 (rev 02)
Mem at 0x08000000 [size=0x4000000]
I/O at 0x00002100 [size=0x100]
Mem at 0x10008000 [size=0x8000]
Mem at 0x1c000000 [size=0x2000000]
00:14.1 Class 0101: 1002:4856 (rev 01)
I/O at 0x00002200 [size=0x8]
I/O at 0x00002208 [size=0x4]
I/O at 0x00002210 [size=0x8]
I/O at 0x00002218 [size=0x4]
I/O at 0x00002220 [size=0x10]
00:14.2 Class 0c03: 1002:4857 (rev 0a)
Mem at 0x10010000 [size=0x1000]
00:14.5 Class 0401: 1002:4858 (rev 01)
Mem at 0x10011000 [size=0x100]
00:14.6 Class 0703: 1002:4859 (rev 01)
Mem at 0x10011100 [size=0x100]
irq fixup slot 8 vendor 10ec irq 33
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: devfs_debug: 0x0
devfs: boot_options: 0x1
NTFS driver v1.1.22 [Flags: R/O]
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications AB.
i2c-core.o: i2c core module version 2.6.2 (20011118)
i2c-dev.o: i2c /dev entries driver module version 2.6.2 (20011118)
i2c-proc.o version 2.6.2 (20011118)
initialize_kbd: Keyboard failed self test
pty: 256 Unix98 ptys configured
rs_init() APER_PCUIPA_BASE: 200 200 deviceID: 4855 4855
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Testing ttyS0 (0xbe000010, 0xbe000010)...
Testing ttyS1 (0xbe000000, 0xbe000000)...
ttyS00 at 0xbe000010 (irq = 100) is a 16550A
ttyS01 at 0xbe000000 (irq = 99) is a 16550A
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
X225: IDE controller on PCI bus 00 dev a1
X225: chipset revision 1
XILLEON 225 IDE: rev 01 IDE UDMA controller on pci00:14.1
X225: 100% native mode on irq 3
ide0: BM-DMA at 0x2220-0x2227, BIOS settings: hda:DMA, hdb:DMA
probing for hdc: present=0, media=32, probetype=ATA
probing for hdc: present=0, media=32, probetype=ATAPI
probing for hdd: present=0, media=32, probetype=ATA
probing for hdd: present=0, media=32, probetype=ATAPI
probing for hde: present=0, media=32, probetype=ATA
probing for hde: present=0, media=32, probetype=ATAPI
probing for hdf: present=0, media=32, probetype=ATA
probing for hdf: present=0, media=32, probetype=ATAPI
probing for hdg: present=0, media=32, probetype=ATA
probing for hdg: present=0, media=32, probetype=ATAPI
probing for hdh: present=0, media=32, probetype=ATA
probing for hdh: present=0, media=32, probetype=ATAPI
probing for hdi: present=0, media=32, probetype=ATA
probing for hdi: present=0, media=32, probetype=ATAPI
probing for hdj: present=0, media=32, probetype=ATA
probing for hdj: present=0, media=32, probetype=ATAPI
probing for hdk: present=0, media=32, probetype=ATA
probing for hdk: present=0, media=32, probetype=ATAPI
probing for hdl: present=0, media=32, probetype=ATA
probing for hdl: present=0, media=32, probetype=ATAPI
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.24
8139too: pci dev 00:08.0 (id 10ec:8139 rev ff) is an enhanced 8139C+ chip
8139too: Use the "8139cp" driver for improved performance and stability.
eth0: RealTek RTL8139 Fast Ethernet at 0xb0000000, 00:0a:97:02:0e:09, IRQ 33
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
XILLEON Flash mappings:
Search for id:(00 00) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
JEDEC: Found no Core flash device at location zero
Boot FLASH probe failed
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(2) type(1)
Search for id:(00 00) interleave(2) type(1)
Search for id:(00 00) interleave(2) type(1)
Search for id:(00 00) interleave(2) type(2)
Search for id:(00 00) interleave(2) type(2)
Search for id:(00 00) interleave(2) type(2)
JEDEC: Found no User flash device at location zero
User FLASH probe failed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci-pci.c: USB OHCI at membase 0xb0010000, IRQ 2
usb-ohci-pci.c: usb-00:14.2, PCI device 1002:4857 (ATI Technologies Inc)
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: b0010000
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb.c: registered new driver usblp
printer.c: v0.8:USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
IP-Config: Guessing netmask 255.0.0.0
IP-Config: Complete:
device=eth0, addr=10.0.1.3, mask=255.0.0.0, gw=255.255.255.255,
host=10.0.1.3, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=10.0.0.157, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
hub.c: USB new device connect on bus1/2, assigned device number 2
Looking up port of RPC 100003/2 on 10.0.0.157
Looking up port of RPC 100005/1 on 10.0.0.157
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 4k freed
Manufacturer: ????????????????????????
Product: ?????????????Aa123456789
SerialNumber: Aa1234567890
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: KingByte Model: Multi-card R/W Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
Vendor: KingByte Model: Multi-card R/W Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
Vendor: KingByte Model: Multi-card R/W Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
Attached scsi removable disk sdc at scsi0, channel 0, id 0, lun 2
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 0
Raw sense data:0x70 0x00 0x00 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
sda : block size assumed to be 512 bytes, disk size 1GB.
Partition check:
/dev/scsi/host0/bus0/target0/lun0:<7>usb-storage: queuecommand() called
unknown partition table
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 0
Raw sense data:0x70 0x00 0x00 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host0/bus0/target0/lun1:<7>usb-storage: queuecommand() called
unknown partition table
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 0
Raw sense data:0x70 0x00 0x00 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
sdc : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host0/bus0/target0/lun2:<7>usb-storage: queuecommand() called
unknown partition table
Algorithmics/MIPS FPU Emulator v1.5
serial console detected. Disabling virtual terminals.
init started: BusyBox v0.60.2 (2002.04.03-20:48+0000) multi-call binary
Welcome to prototype Linux
Mounting proc filesystem: [ OK ]
Configuring kernel parameters: [ OK ]
Activating swap partitions: [ OK ]
Setting hostname prototype: [ OK ]
Mounting local filesystems: [ OK ]
Enabling swap space: [ OK ]
Entering non-interactive startup
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting xinetd: [ OK ]
Setting clock: Fri Dec 31 19:00:33 EST 1999 [ OK ]
prototype login: usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Skipping START_STOP command
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 01 00 8b 81 f4 ff ff ff
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: -- Stall on control pipe. Clearing
usb-storage: -- usb_clear_halt() returns 0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x6, ASC: 0x28, ASCQ: 0x0
usb-storage: Unit Attention: not ready to ready transition
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 00 00 3c 80 20 f1 3c 80
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
login:
Login timed out after 60 secon
prototype login:
As I said before, the max_scsi_luns=0 case was less interesting, but I
append the console output here anyway:
memsize environment variable not set: assuming 32MB
CPU revision is: 00018007
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Linux version 2.4.18_dev-xilleon_x220 (dave@vmrh73g.localdomain) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-99.1)) #24 Thu Mar 13 09:38:57 PST 2003
KGDB: Using serial line /dev/ttyS1 for session
Determined physical RAM map:
memory: 00080000 @ 00000000 (ROM data)
memory: 00080000 @ 00080000 (reserved)
memory: 01f00000 @ 00100000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: nfsroot=10.0.0.157:/nfsroot,rw,rsize=1024,wsize=1024 max_scsi_luns=0 hda=none hdb=none rw ip=10.0.1.3 console=ttyS0,115200,n,8,1
ide_setup: hda=none
ide_setup: hdb=none
Initializing IRQs
calculating r4koff... CPU frequency 598.42 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 598.01 BogoMIPS
MIPS CPU counter frequency is fixed at 299209896 Hz
Memory: 28456k/31744k available (2230k kernel code, 3288k reserved, 323k data, 4k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Autoconfig PCI channel 0x803804e8
Scanning bus 00, I/O 0x00002000:0x00010001, Mem 0x10000000:0x18000001
00:08.0 Class 0200: 10ec:8139 (rev 10)
I/O at 0x00002000 [size=0x100]
Mem at 0x10000000 [size=0x100]
00:14.0 Class 0480: 1002:4855 (rev 02)
Mem at 0x08000000 [size=0x4000000]
I/O at 0x00002100 [size=0x100]
Mem at 0x10008000 [size=0x8000]
Mem at 0x1c000000 [size=0x2000000]
00:14.1 Class 0101: 1002:4856 (rev 01)
I/O at 0x00002200 [size=0x8]
I/O at 0x00002208 [size=0x4]
I/O at 0x00002210 [size=0x8]
I/O at 0x00002218 [size=0x4]
I/O at 0x00002220 [size=0x10]
00:14.2 Class 0c03: 1002:4857 (rev 0a)
Mem at 0x10010000 [size=0x1000]
00:14.5 Class 0401: 1002:4858 (rev 01)
Mem at 0x10011000 [size=0x100]
00:14.6 Class 0703: 1002:4859 (rev 01)
Mem at 0x10011100 [size=0x100]
irq fixup slot 8 vendor 10ec irq 33
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: devfs_debug: 0x0
devfs: boot_options: 0x1
NTFS driver v1.1.22 [Flags: R/O]
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications AB.
i2c-core.o: i2c core module version 2.6.2 (20011118)
i2c-dev.o: i2c /dev entries driver module version 2.6.2 (20011118)
i2c-proc.o version 2.6.2 (20011118)
initialize_kbd: Keyboard failed self test
pty: 256 Unix98 ptys configured
rs_init() APER_PCUIPA_BASE: 200 200 deviceID: 4855 4855
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Testing ttyS0 (0xbe000010, 0xbe000010)...
Testing ttyS1 (0xbe000000, 0xbe000000)...
ttyS00 at 0xbe000010 (irq = 100) is a 16550A
ttyS01 at 0xbe000000 (irq = 99) is a 16550A
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
X225: IDE controller on PCI bus 00 dev a1
X225: chipset revision 1
XILLEON 225 IDE: rev 01 IDE UDMA controller on pci00:14.1
X225: 100% native mode on irq 3
ide0: BM-DMA at 0x2220-0x2227, BIOS settings: hda:DMA, hdb:DMA
probing for hdc: present=0, media=32, probetype=ATA
probing for hdc: present=0, media=32, probetype=ATAPI
probing for hdd: present=0, media=32, probetype=ATA
probing for hdd: present=0, media=32, probetype=ATAPI
probing for hde: present=0, media=32, probetype=ATA
probing for hde: present=0, media=32, probetype=ATAPI
probing for hdf: present=0, media=32, probetype=ATA
probing for hdf: present=0, media=32, probetype=ATAPI
probing for hdg: present=0, media=32, probetype=ATA
probing for hdg: present=0, media=32, probetype=ATAPI
probing for hdh: present=0, media=32, probetype=ATA
probing for hdh: present=0, media=32, probetype=ATAPI
probing for hdi: present=0, media=32, probetype=ATA
probing for hdi: present=0, media=32, probetype=ATAPI
probing for hdj: present=0, media=32, probetype=ATA
probing for hdj: present=0, media=32, probetype=ATAPI
probing for hdk: present=0, media=32, probetype=ATA
probing for hdk: present=0, media=32, probetype=ATAPI
probing for hdl: present=0, media=32, probetype=ATA
probing for hdl: present=0, media=32, probetype=ATAPI
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.24
8139too: pci dev 00:08.0 (id 10ec:8139 rev ff) is an enhanced 8139C+ chip
8139too: Use the "8139cp" driver for improved performance and stability.
eth0: RealTek RTL8139 Fast Ethernet at 0xb0000000, 00:0a:97:02:0e:09, IRQ 33
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
XILLEON Flash mappings:
Search for id:(00 00) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
JEDEC: Found no Core flash device at location zero
Boot FLASH probe failed
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(1) type(2)
Search for id:(00 00) interleave(2) type(1)
Search for id:(00 00) interleave(2) type(1)
Search for id:(00 00) interleave(2) type(1)
Search for id:(00 00) interleave(2) type(2)
Search for id:(00 00) interleave(2) type(2)
Search for id:(00 00) interleave(2) type(2)
JEDEC: Found no User flash device at location zero
User FLASH probe failed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci-pci.c: USB OHCI at membase 0xb0010000, IRQ 2
usb-ohci-pci.c: usb-00:14.2, PCI device 1002:4857 (ATI Technologies Inc)
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: b0010000
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb.c: registered new driver usblp
printer.c: v0.8:USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
IP-Config: Guessing netmask 255.0.0.0
IP-Config: Complete:
device=eth0, addr=10.0.1.3, mask=255.0.0.0, gw=255.255.255.255,
host=10.0.1.3, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=10.0.0.157, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
hub.c: USB new device connect on bus1/2, assigned device number 2
Looking up port of RPC 100003/2 on 10.0.0.157
Looking up port of RPC 100005/1 on 10.0.0.157
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 4k freed
Manufacturer: ????????????????????????
Product: ?????????????Aa123456789
SerialNumber: Aa1234567890
scsi0 : SCSI emulation for USB Mass Storage devices
Algorithmics/MIPS FPU Emulator v1.5
serial console detected. Disabling virtual terminals.
init started: BusyBox v0.60.2 (2002.04.03-20:48+0000) multi-call binary
Welcome to prototype Linux
Mounting proc filesystem: [ OK ]
Configuring kernel parameters: [ OK ]
Activating swap partitions: [ OK ]
Setting hostname prototype: [ OK ]
Mounting local filesystems: [ OK ]
Enabling swap space: [ OK ]
^@Entering non-interactive startup
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting xinetd: [ OK ]
Setting clock: Fri Dec 31 19:00:18 EST 1999 [ OK ]
prototype login:
Thanks for the help!
Dave
next prev parent reply other threads:[~2003-03-15 2:33 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-03-14 18:39 Trying to troubleshoot ornery Phison usb-storage David Wuertele
2003-03-14 20:24 ` Matthew Dharm
2003-03-14 21:01 ` David Wuertele
2003-03-14 22:47 ` Matthew Dharm
2003-03-14 23:00 ` David Wuertele
2003-03-15 1:55 ` Matthew Dharm
2003-03-15 2:27 ` David Wuertele [this message]
2003-03-16 0:13 ` Matthew Dharm
2003-03-21 2:01 ` write protect seems wrong (was Re: Trying to troubleshoot ornery Phison usb-storage) David Wuertele
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=m37kb1jreb.fsf@bfnet.com \
--to=dave-gnus@bfnet.com \
--cc=linux-scsi@vger.kernel.org \
--cc=linux-usb-users@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.