From: "Frederic Corne" <fcorne@free.fr>
To: linux-hotplug@vger.kernel.org
Subject: problem of re-insertion of a scsi card
Date: Fri, 12 Sep 2003 12:23:03 +0000 [thread overview]
Message-ID: <marc-linux-hotplug-106337091917609@msgid-missing> (raw)
Hello,
I have a problem with a pcmcia scsi card. I have posted the question on
the pcmcia-cs forum but it apears that this is more a hotplug problem.
I have a Adaptec 1480 card to which I connect a scanner and a cdrw.
When I first insert the card , all is ok , the scanner and the cdrw work
nicelly.
But if I eject the card and later re-insert it , the card is recognized
but the scsi chain is not re-initialized. There is not any entry in the
scsi subsystem.
I have triied to reload some kernel modules without success.
what can I do ?
Any help will be very appreciated.
FC
here is the logs
the machine is a basic Mandrake 9.1
kernel 2.4.21-0.25mdk
pcmcia-cs-3.2.3-5mdk
hotplug-2002_04_01-8mdk
I first insert the card.
tail /var/log/message
( a lot of error about irda that I have not yet corrected because the
notebock is upon a dock)
Sep 6 22:12:52 poussindev kernel: cs: cb_alloc(bus 21): vendor 0x9004,
device 0x6075
Sep 6 22:12:52 poussindev kernel: PCI: Enabling device 15:00.0 (0000 -> 0003)
Sep 6 22:12:52 poussindev cardmgr[19056]: socket 1: CardBus hotplug device
Sep 6 22:12:52 poussindev /etc/hotplug/pci.agent: pcimodules is scanning
more than ...
Sep 6 22:12:52 poussindev /etc/hotplug/pci.agent: Setup aic7xxx 3c59x
yenta_socket toshoboe donauboe eepro100 e100 usb-uhci uhci neofb for PCI
slot 15:00.0
Sep 6 22:12:52 poussindev kernel: ahc_pci:21:0:0: Host Adapter Bios
disabled. Using default SCSI device parameters
Sep 6 22:12:52 poussindev kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI
SCSI HBA DRIVER, Rev 6.2.8
Sep 6 22:12:52 poussindev kernel: <Adaptec 1480A Ultra SCSI adapter>
Sep 6 22:12:52 poussindev kernel: aic7860: Ultra Single Channel A, SCSI
Id=7, 3/253 SCBs
Sep 6 22:12:52 poussindev kernel:
Sep 6 22:13:09 poussindev kernel: Vendor: YAMAHA Model: CRW4416S Rev: 1.0j
Sep 6 22:13:09 poussindev kernel: Type: CD-ROM ANSI SCSI revision: 02
Sep 6 22:13:09 poussindev kernel: Vendor: UMAX Model: Astra 1220S Rev: V1.3
Sep 6 22:13:09 poussindev kernel: Type: Scanner ANSI SCSI revision: 02
Sep 6 22:13:09 poussindev kernel: Attached scsi CD-ROM sr0 at scsi0,
channel 0, id 5, lun 0
Sep 6 22:13:09 poussindev kernel: Attached scsi generic sg1 at scsi0,
channel 0, id 6, lun 0, type 6
Sep 6 22:13:09 poussindev kernel: (scsi0:A:5): 8.333MB/s transfers
(8.333MHz, offset 15)
Sep 6 22:13:09 poussindev kernel: sr0: scsi3-mmc drive: 16x/16x writer
cd/rw xa/form2 cdda tray
Sep 6 22:13:10 poussindev insmod:
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/irda/donauboe.o.gz:
init_module: No such device
Sep 6 22:13:10 poussindev insmod: Hint: insmod errors can be caused by
incorrect module parameters, including invalid IO or IRQ parameters. You
may find more information in syslog or the output from dmesg
Sep 6 22:13:10 poussindev modprobe: modprobe: insmod
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/irda/donauboe.o.gz failed
Sep 6 22:13:10 poussindev modprobe: modprobe: insmod donauboe failed
Sep 6 22:13:10 poussindev /etc/hotplug/pci.agent: ... can't load module
donauboe
Sep 6 22:13:10 poussindev /etc/hotplug/pci.agent: missing kernel or user
mode driver donauboe
Sep 6 22:13:11 poussindev insmod:
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/e100/e100.o.gz:
init_module: No such device
Sep 6 22:13:11 poussindev insmod: Hint: insmod errors can be caused by
incorrect module parameters, including invalid IO or IRQ parameters. You
may find more information in syslog or the output from dmesg
Sep 6 22:13:11 poussindev modprobe: modprobe: insmod
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/e100/e100.o.gz failed
Sep 6 22:13:11 poussindev modprobe: modprobe: insmod e100 failed
Sep 6 22:13:11 poussindev /etc/hotplug/pci.agent: ... can't load module e100
Sep 6 22:13:11 poussindev /etc/hotplug/pci.agent: missing kernel or user
mode driver e100
Sep 6 22:13:11 poussindev /etc/hotplug/pci.agent: ... blacklisted module:
usb-uhci
Sep 6 22:13:11 poussindev kernel: uhci.c: USB Universal Host Controller
Interface driver v1.1
Sep 6 22:13:11 poussindev insmod:
/lib/modules/2.4.21-0.25mdk/kernel/drivers/usb/uhci.o.gz: init_module: No
such device
Sep 6 22:13:11 poussindev insmod: Hint: insmod errors can be caused by
incorrect module parameters, including invalid IO or IRQ parameters. You
may find more information in syslog or the output from dmesg
Sep 6 22:13:11 poussindev modprobe: modprobe: insmod
/lib/modules/2.4.21-0.25mdk/kernel/drivers/usb/uhci.o.gz failed
Sep 6 22:13:11 poussindev modprobe: modprobe: insmod uhci failed
Sep 6 22:13:11 poussindev /etc/hotplug/pci.agent: ... can't load module uhci
Sep 6 22:13:11 poussindev /etc/hotplug/pci.agent: missing kernel or user
mode driver uhci
# dump_cis
Socket 0:
manfid 0x0101, 0x5257
config_cb base 0x0000 last_index 0x01
cftable_entry_cb 0x01 [default]
[master]
Vcc Vnom 3300mV
Vpp1 Vnom 3300mV
io_base 1
irq mask 0xffff [level]
BAR 1 size 64b [io]
vers_1 5.0, "3Com Corporation", "3CCFE575CT", "LAN Cardbus Card",
"004"
funcid network_adapter [post]
Socket 1:
manfid 0x012f, 0xcb01
vers_1 5.0, "Adaptec", "APA-1480 SCSI Host Adapter",
"Version 1.10 ", ""
funcid scsi_adapter
BAR 1 size 256b [io]
BAR 2 size 256b [mem]
BAR 7 size 2kb [mem]
config_cb base 0x00f2 last_index 0x00
cftable_entry_cb 0x00 [default]
Vcc Vnom 3300mV Istatic 150mA Iavg 230mA Ipeak 300mA
io_base 1
irq mask 0xffff [level] [shared]
mem_base 2 7
# cardctl status
Socket 0:
3.3V CardBus card
function 0: [ready]
Socket 1:
3.3V CardBus card
function 0: [ready]
# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: YAMAHA Model: CRW4416S Rev: 1.0j
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: UMAX Model: Astra 1220S Rev: V1.3
Type: Scanner ANSI SCSI revision: 02
As you see all is ok . the scanner and the cdrw work nicelly.
Now I eject the card :
# cardctl eject 1
tail /var/log/message
Sep 6 22:18:56 poussindev kernel: cs: cb_free(bus 21)
Sep 6 22:18:56 poussindev /etc/hotplug/pci.agent: PCI remove event not
supported
# cardctl status
Socket 0:
3.3V CardBus card
function 0: [ready]
Socket 1:
no card
# cat /proc/scsi/scsi
Attached devices: none
# lsmod
Module Size Used by Not tainted
aic7xxx 128536 0 (unused)
ipt_state 1080 2 (autoclean)
ipt_REJECT 3768 1 (autoclean)
ipt_LOG 4280 1 (autoclean)
iptable_filter 2348 1 (autoclean)
ip_nat_ftp 4016 0 (unused)
iptable_nat 21016 2 [ip_nat_ftp]
ip_conntrack_ftp 5200 1
ip_conntrack 27432 3 [ipt_state ip_nat_ftp iptable_nat ip_conntrack_ftp]
ip_tables 14648 7 [ipt_state ipt_REJECT ipt_LOG iptable_filter iptable_nat]
ppp_synctty 7488 0 (unused)
ppp_async 9216 1
ppp_generic 24060 3 [ppp_synctty ppp_async]
slhc 6564 0 [ppp_generic]
lp 8096 0
parport_pc 25096 1
parport 34176 1 [lp parport_pc]
sg 34636 0 (autoclean) (unused)
st 29488 0 (autoclean) (unused)
sr_mod 16952 0 (autoclean) (unused)
sd_mod 13132 0 (autoclean) (unused)
scsi_mod 103540 5 (autoclean) [aic7xxx sg st sr_mod sd_mod]
neofb 15560 0 (unused)
nfsd 74256 8 (autoclean)
toshoboe 7400 0 (unused)
irda 112112 0 [toshoboe]
3c59x 29584 1
ds 8456 2
yenta_socket 13056 2
pcmcia_core 57184 0 [ds yenta_socket]
af_packet 14952 2 (autoclean)
ide-floppy 15580 0 (autoclean)
ide-tape 48304 0 (autoclean)
ide-cd 33856 0 (autoclean)
cdrom 31648 0 (autoclean) [sr_mod ide-cd]
floppy 55100 0
eepro100 21844 1 (autoclean)
mii 3832 0 (autoclean) [eepro100]
supermount 15296 2 (autoclean)
usb-uhci 24684 0 (unused)
usbcore 72992 1 [usb-uhci]
rtc 8060 0 (autoclean)
ext3 59756 4
jbd 39100 4 [ext3]
# rmmod aic7xxx
# rmmod -a
Now I re-insert the card :
tail /var/log/message :
Sep 6 22:45:51 poussindev kernel: cs: cb_alloc(bus 21): vendor 0x9004,
device 0x6075
Sep 6 22:45:51 poussindev kernel: PCI: Enabling device 15:00.0 (0000 -> 0003)
Sep 6 22:45:51 poussindev /etc/hotplug/pci.agent: pcimodules is scanning
more than ...
Sep 6 22:45:51 poussindev /etc/hotplug/pci.agent: Setup aic7xxx 3c59x
yenta_socket toshoboe donauboe eepro100 e100 usb-uhci uhci neofb for PCI
slot 15:00.0
Sep 6 22:45:53 poussindev insmod:
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/irda/donauboe.o.gz:
init_module: No such device
Sep 6 22:45:53 poussindev insmod: Hint: insmod errors can be caused by
incorrect module parameters, including invalid IO or IRQ parameters. You
may find more information in syslog or the output from dmesg
Sep 6 22:45:53 poussindev modprobe: modprobe: insmod
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/irda/donauboe.o.gz failed
Sep 6 22:45:53 poussindev modprobe: modprobe: insmod donauboe failed
Sep 6 22:45:53 poussindev /etc/hotplug/pci.agent: ... can't load module
donauboe
Sep 6 22:45:53 poussindev /etc/hotplug/pci.agent: missing kernel or user
mode driver donauboe
Sep 6 22:45:53 poussindev insmod:
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/e100/e100.o.gz:
init_module: No such device
Sep 6 22:45:53 poussindev insmod: Hint: insmod errors can be caused by
incorrect module parameters, including invalid IO or IRQ parameters. You
may find more information in syslog or the output from dmesg
Sep 6 22:45:53 poussindev modprobe: modprobe: insmod
/lib/modules/2.4.21-0.25mdk/kernel/drivers/net/e100/e100.o.gz failed
Sep 6 22:45:53 poussindev modprobe: modprobe: insmod e100 failed
Sep 6 22:45:53 poussindev /etc/hotplug/pci.agent: ... can't load module e100
Sep 6 22:45:53 poussindev /etc/hotplug/pci.agent: missing kernel or user
mode driver e100
Sep 6 22:45:53 poussindev /etc/hotplug/pci.agent: ... blacklisted module:
usb-uhci
Sep 6 22:45:54 poussindev kernel: uhci.c: USB Universal Host Controller
Interface driver v1.1
Sep 6 22:45:54 poussindev insmod:
/lib/modules/2.4.21-0.25mdk/kernel/drivers/usb/uhci.o.gz: init_module: No
such device
Sep 6 22:45:54 poussindev insmod: Hint: insmod errors can be caused by
incorrect module parameters, including invalid IO or IRQ parameters. You
may find more information in syslog or the output from dmesg
Sep 6 22:45:54 poussindev modprobe: modprobe: insmod
/lib/modules/2.4.21-0.25mdk/kernel/drivers/usb/uhci.o.gz failed
Sep 6 22:45:54 poussindev modprobe: modprobe: insmod uhci failed
Sep 6 22:45:54 poussindev /etc/hotplug/pci.agent: ... can't load module uhci
Sep 6 22:45:54 poussindev /etc/hotplug/pci.agent: missing kernel or user
mode driver uhci
# dump_cis
Socket 0:
manfid 0x0101, 0x5257
config_cb base 0x0000 last_index 0x01
cftable_entry_cb 0x01 [default]
[master]
Vcc Vnom 3300mV
Vpp1 Vnom 3300mV
io_base 1
irq mask 0xffff [level]
BAR 1 size 64b [io]
vers_1 5.0, "3Com Corporation", "3CCFE575CT", "LAN Cardbus Card",
"004"
funcid network_adapter [post]
Socket 1:
manfid 0x012f, 0xcb01
vers_1 5.0, "Adaptec", "APA-1480 SCSI Host Adapter",
"Version 1.10 ", ""
funcid scsi_adapter
BAR 1 size 256b [io]
BAR 2 size 256b [mem]
BAR 7 size 2kb [mem]
config_cb base 0x00f2 last_index 0x00
cftable_entry_cb 0x00 [default]
Vcc Vnom 3300mV Istatic 150mA Iavg 230mA Ipeak 300mA
io_base 1
irq mask 0xffff [level] [shared]
mem_base 2 7
# cardctl status
Socket 0:
3.3V CardBus card
function 0: [ready]
Socket 1:
3.3V CardBus card
function 0: [ready]
BUT THERE IS NOT SCSI !!! :
cat /proc/scsi/scsi
Attached devices: none
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
next reply other threads:[~2003-09-12 12:23 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-09-12 12:23 Frederic Corne [this message]
2003-09-16 16:39 ` problem of re-insertion of a scsi card Greg KH
-- strict thread matches above, loose matches on Subject: below --
2003-09-19 16:16 Frederic Corne
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=marc-linux-hotplug-106337091917609@msgid-missing \
--to=fcorne@free.fr \
--cc=linux-hotplug@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.