From mboxrd@z Thu Jan 1 00:00:00 1970 From: Stephan van Hienen Date: Thu, 14 May 1998 00:27:58 +0000 Subject: 2 weird problems (second ide) Message-Id: List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="windows-1252" Content-Transfer-Encoding: quoted-printable To: ultralinux@vger.kernel.org and now ide : hda: dma_intr: status=3D0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=3D0x40 { UncorrectableError }, LBAsect=131139, sector=131138 end_request: I/O error, dev 03:01 (ide), sector 131138 EXT2-fs error (device 03:01): ext2_read_inode: unable to read inode block - inode=16496, blocke569 =20 and i get this lot of times i think the hd is not set ok somewhere (internal seagate 4gb with sun ultra sparc 10) here some info : CMD646: IDE controller on PCI bus 01 dev 18 CMD646: 100% native mode on irq c00007e0 ide0: BM-DMA at 0xfffff9fe02c00020-0xfffff9fe02c00027, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xfffff9fe02c00028-0xfffff9fe02c0002f, BIOS settings: hdc:pio, hdd:pio hda: ST34342A, ATA DISK drive hdb: ST34342A, ATA DISK drive ide0 at 0x2c00000-0x2c00007,0x2c0000a on irq -1073739808 CMD646: MDMA enable [SELECT SETXFER CMND wait STAT(50) SETFEATURE wait STAT(d0) STAT(d0) STAT(50) DMA_CAP DONE] hda: ST34342A, 4103MB w/128kB Cache, CHS=8894/15/63, DMA CMD646: MDMA enable [SELECT SETXFER CMND wait STAT(50) SETFEATURE wait STAT(d0) STAT(d0) STAT(d0) STAT(50) DMA_CAP DONE] hdb: ST34342A, 4103MB w/128kB Cache, CHS=8894/15/63, DMA =20 Partition check: hda: hda1 hda2 hda3 hdb: =20 (second hd not used for now) [root@sun /root]# fdisk Using /dev/hda as default device! The number of cylinders for this disk is set to 8894. This is larger than 1024, and may cause problems with: 1) software that runs at boot time (e.g., LILO) 2) booting and partitioning software form other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): p Disk /dev/hda (Sun disk label): 15 heads, 63 sectors, 8892 cylinders Units =3D cylinders of 945 * 512 bytes Device Flag Begin Start End Blocks Id System /dev/hda1 0 0 8784 4150440 83 Linux native /dev/hda2 u 8784 8784 8892 51030 82 Linux swap /dev/hda3 0 0 8892 4201470 5 Whole disk =20 Command (m for help): s 0 custom (with hardware detected defaults) Select type (? for auto, 0 for custom): 0 Heads (1-[15]-1024): Sectors/track (1-[63]-1024): Cylinders (1-[8892]-65535): Alternate cylinders (0-[2]-65535): Physical cylinders (0-[8894]-65535): Rotation speed (rpm) (1-[5400]-100000): Interleave factor (1-[1]-32): Extra sectors per cylinder (0-[0]-63): =20 need more info ? and everytime i reboot i get the fsck checking my hd