From: "U.Mutlu" <for-gmane@mutluit.com>
To: linux-scsi@vger.kernel.org
Subject: How to set DPOFUA=0 ?
Date: Sat, 26 Dec 2015 02:25:56 +0100 [thread overview]
Message-ID: <n5kqb4$k8n$1@ger.gmane.org> (raw)
Hi,
I have got 2 different submodels of the SSD Samsung 850 Evo 500 GB.
The first one has DPOFUA=0, the second one has DPOFUA=1 (see below).
That with DPOFUA=0 works fine, but the other with DPOFUA=1 doesn't work
after mounting; it reports errors and switches to read-only mount.
It seems Linux has a problem with DPOFUA=1, so then IMO best would be to
disable that feature of the device. So, how & where can DPOFUA be set to value 0 ?
Thx
############################################################################
# uname -a
Linux panther 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt20-1+deb8u1 (2015-12-14)
x86_64 GNU/Linux
############################################################################
Dec 26 00:45:38 panther vmunix: [ 2337.193164] usb 4-1: new SuperSpeed USB
device number 2 using xhci_hcd
Dec 26 00:45:38 panther vmunix: [ 2337.212852] usb 4-1: New USB device found,
idVendor=357d, idProduct=7788
Dec 26 00:45:38 panther vmunix: [ 2337.212861] usb 4-1: New USB device
strings: Mfr=1, Product=2, SerialNumber=3
Dec 26 00:45:38 panther vmunix: [ 2337.212866] usb 4-1: Product: USB to
ATA/ATAPI Bridge
Dec 26 00:45:38 panther vmunix: [ 2337.212870] usb 4-1: Manufacturer: JMicron
Dec 26 00:45:38 panther vmunix: [ 2337.212874] usb 4-1: SerialNumber:
321AE8171482926
Dec 26 00:45:38 panther vmunix: [ 2337.245338] usb-storage 4-1:1.0: USB Mass
Storage device detected
Dec 26 00:45:38 panther vmunix: [ 2337.245591] scsi2 : usb-storage 4-1:1.0
Dec 26 00:45:38 panther vmunix: [ 2337.245770] usbcore: registered new
interface driver usb-storage
Dec 26 00:45:39 panther vmunix: [ 2338.244729] scsi 2:0:0:0: Direct-Access
Samsung SSD 850 EVO 500G 0114 PQ: 0 ANSI: 6
Dec 26 00:45:39 panther vmunix: [ 2338.245308] sd 2:0:0:0: Attached scsi
generic sg2 type 0
Dec 26 00:45:39 panther vmunix: [ 2338.247115] sd 2:0:0:0: [sdb] Spinning up
disk...
Dec 26 00:45:49 panther vmunix: [ 2339.251034] .........
Dec 26 00:45:52 panther vmunix: [ 2348.278894] ....ready
Dec 26 00:45:52 panther vmunix: [ 2351.288429] sd 2:0:0:0: [sdb] 976773168
512-byte logical blocks: (500 GB/465 GiB)
Dec 26 00:45:52 panther vmunix: [ 2351.288953] sd 2:0:0:0: [sdb] Write Protect
is off
Dec 26 00:45:52 panther vmunix: [ 2351.288959] sd 2:0:0:0: [sdb] Mode Sense:
47 00 10 08
Dec 26 00:45:52 panther vmunix: [ 2351.289447] sd 2:0:0:0: [sdb] Write cache:
enabled, read cache: enabled, supports DPO and FUA
Dec 26 00:45:52 panther vmunix: [ 2351.293763] sdb: sdb1 sdb2 sdb3
Dec 26 00:45:52 panther vmunix: [ 2351.295862] sd 2:0:0:0: [sdb] Attached SCSI
disk
Dec 26 00:47:02 panther vmunix: [ 2421.091552] EXT4-fs (sdb1): mounted
filesystem with ordered data mode. Opts: (null)
Dec 26 00:47:09 panther vmunix: [ 2428.394003] sd 2:0:0:0: [sdb] Invalid
command failure
Dec 26 00:47:09 panther vmunix: [ 2428.394013] sd 2:0:0:0: [sdb]
Dec 26 00:47:09 panther vmunix: [ 2428.394017] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Dec 26 00:47:09 panther vmunix: [ 2428.394021] sd 2:0:0:0: [sdb]
Dec 26 00:47:09 panther vmunix: [ 2428.394024] Sense Key : Illegal Request
[current]
Dec 26 00:47:09 panther vmunix: [ 2428.394030] sd 2:0:0:0: [sdb]
Dec 26 00:47:09 panther vmunix: [ 2428.394034] Add. Sense: Invalid field in cdb
Dec 26 00:47:09 panther vmunix: [ 2428.394038] sd 2:0:0:0: [sdb] CDB:
Dec 26 00:47:09 panther vmunix: [ 2428.394040] Write(10): 2a 08 02 04 08 20 00
00 08 00
Dec 26 00:47:09 panther vmunix: [ 2428.394054] end_request: critical target
error, dev sdb, sector 33818656
Dec 26 00:47:09 panther vmunix: [ 2428.394059] end_request: critical target
error, dev sdb, sector 33818656
Dec 26 00:47:09 panther vmunix: [ 2428.394120] Aborting journal on device sdb1-8.
Dec 26 00:47:09 panther vmunix: [ 2428.471535] EXT4-fs error (device sdb1):
ext4_journal_check_start:56: Detected aborted journal
Dec 26 00:47:09 panther vmunix: [ 2428.471547] EXT4-fs (sdb1): Remounting
filesystem read-only
############################################################################
# sdparm -a --long /dev/sda
/dev/sda: ATA Samsung SSD 850 1B6Q
Direct access device specific parameters: WP=0 DPOFUA=0
Read write error recovery [rw] mode page:
AWRE 1 [cha: n, def: 1] Automatic write reallocation enabled
ARRE 0 [cha: n, def: 0] Automatic read reallocation enabled
TB 0 [cha: n, def: 0] Transfer block
RC 0 [cha: n, def: 0] Read continuous
EER 0 [cha: n, def: 0] Enable early recovery
PER 0 [cha: n, def: 0] Post error
DTE 0 [cha: n, def: 0] Data terminate on error
DCR 0 [cha: n, def: 0] Disable correction
RRC 0 [cha: n, def: 0] Read retry count
COR_S 0 [cha: n, def: 0] Correction span (obsolete)
HOC 0 [cha: n, def: 0] Head offset count (obsolete)
DSOC 0 [cha: n, def: 0] Data strobe offset count (obsolete)
LBPERE 0 [cha: n, def: 0] Logical block provisioning error
reporting enabled
WRC 0 [cha: n, def: 0] Write retry count
RTL 0 [cha: n, def: 0] Recovery time limit (ms)
Caching (SBC) [ca] mode page:
IC 0 [cha: n, def: 0] Initiator control
ABPF 0 [cha: n, def: 0] Abort pre-fetch
CAP 0 [cha: n, def: 0] Caching analysis permitted
DISC 0 [cha: n, def: 0] Discontinuity
SIZE 0 [cha: n, def: 0] Size enable
WCE 1 [cha: y, def: 1] Write cache enable
MF 0 [cha: n, def: 0] Multiplication factor
RCD 0 [cha: n, def: 0] Read cache disable
DRRP 0 [cha: n, def: 0] Demand read retention priority
WRP 0 [cha: n, def: 0] Write retention priority
DPTL 0 [cha: n, def: 0] Disable pre-fetch transfer length
MIPF 0 [cha: n, def: 0] Minimum pre-fetch
MAPF 0 [cha: n, def: 0] Maximum pre-fetch
MAPFC 0 [cha: n, def: 0] Maximum pre-fetch ceiling
FSW 0 [cha: n, def: 0] Force sequential write
LBCSS 0 [cha: n, def: 0] Logical block cache segment size
DRA 0 [cha: n, def: 0] Disable read ahead
SYNC_PROG 0 [cha: n, def: 0] Synchronous cache progress indication
NV_DIS 0 [cha: n, def: 0] Non-volatile cache disable
NCS 0 [cha: n, def: 0] Number of cache segments
CSS 0 [cha: n, def: 0] Cache segment size
Control [co] mode page:
TST 0 [cha: n, def: 0] Task set type
TMF_ONLY 0 [cha: n, def: 0] Task management functions only
DPICZ 0 [cha: n, def: 0] Disable protection information check if
protect field zero
D_SENSE 0 [cha: n, def: 0] Descriptor format sense data
GLTSD 1 [cha: n, def: 1] Global logging target save disable
RLEC 0 [cha: n, def: 0] Report log exception condition
QAM 0 [cha: n, def: 0] Queue algorithm modifier
NUAR 0 [cha: n, def: 0] No unit attention on release
QERR 0 [cha: n, def: 0] Queue error management
RAC 0 [cha: n, def: 0] Report a check
UA_INTLCK 0 [cha: n, def: 0] Unit attention interlocks control
SWP 0 [cha: n, def: 0] Software write protect
ATO 0 [cha: n, def: 0] Application tag owner
TAS 0 [cha: n, def: 0] Task aborted status
ATMPE 0 [cha: n, def: 0] Application tag mode page enabled
RWWP 0 [cha: n, def: 0] Reject write without protection
AUTOLOAD 0 [cha: n, def: 0] Autoload mode
BTP -1 [cha: n, def: -1] Busy timeout period (100us)
ESTCT 30 [cha: n, def: 30] Extended self test completion time (sec)
############################################################################
# sdparm -a --long /dev/sdb
/dev/sdb: Samsung SSD 850 EVO 500G 0114
Direct access device specific parameters: WP=0 DPOFUA=1
Caching (SBC) [ca] mode page:
IC 0 [cha: n, def: 0, sav: 0] Initiator control
ABPF 0 [cha: n, def: 0, sav: 0] Abort pre-fetch
CAP 0 [cha: n, def: 0, sav: 0] Caching analysis permitted
DISC 1 [cha: n, def: 1, sav: 1] Discontinuity
SIZE 0 [cha: n, def: 0, sav: 0] Size enable
WCE 1 [cha: n, def: 1, sav: 1] Write cache enable
MF 0 [cha: n, def: 0, sav: 0] Multiplication factor
RCD 0 [cha: n, def: 0, sav: 0] Read cache disable
DRRP 0 [cha: n, def: 0, sav: 0] Demand read retention priority
WRP 0 [cha: n, def: 0, sav: 0] Write retention priority
DPTL -1 [cha: n, def: -1, sav: -1] Disable pre-fetch transfer length
MIPF 0 [cha: n, def: 0, sav: 0] Minimum pre-fetch
MAPF -1 [cha: n, def: -1, sav: -1] Maximum pre-fetch
MAPFC -1 [cha: n, def: -1, sav: -1] Maximum pre-fetch ceiling
FSW 0 [cha: n, def: 0, sav: 0] Force sequential write
LBCSS 0 [cha: n, def: 0, sav: 0] Logical block cache segment size
DRA 0 [cha: n, def: 0, sav: 0] Disable read ahead
SYNC_PROG 0 [cha: n, def: 0, sav: 0] Synchronous cache progress
indication
NV_DIS 0 [cha: n, def: 0, sav: 0] Non-volatile cache disable
NCS 255 [cha: n, def:255, sav:255] Number of cache segments
CSS 0 [cha: n, def: 0, sav: 0] Cache segment size
Power condition [po] mode page:
PM_BG 0 [cha: n, def: 0, sav: 0] Power management, background
functions, precedence
STANDBY_Y 0 [cha: n, def: 0, sav: 0] Standby_y timer enable
IDLE_C 0 [cha: n, def: 0, sav: 0] Idle_c timer enable
IDLE_B 0 [cha: n, def: 0, sav: 0] Idle_b timer enable
IDLE 0 [cha: n, def: 0, sav: 0] Idle_a timer enable
STANDBY 0 [cha: y, def: 1, sav: 0] Standby_z timer enable
ICT 0 [cha: n, def: 0, sav: 0] Idle_a condition timer (100 ms)
SCT 0 [cha: y, def:18000, sav: 0] Standby_z condition timer (100 ms)
IBCT 0 [cha: n, def: 0, sav: 0] Idle_b condition timer (100 ms)
ICCT 0 [cha: n, def: 0, sav: 0] Idle_c condition timer (100 ms)
SYCT 0 [cha: n, def: 0, sav: 0] Standby_y condition timer (100 ms)
CCF_IDLE 0 [cha: n, def: 0, sav: 0] check condition on transition
from idle
CCF_STAND 0 [cha: n, def: 0, sav: 0] check condition on transition
from standby
CCF_STOPP 0 [cha: n, def: 0, sav: 0] check condition on transition
from stopped
############################################################################
next reply other threads:[~2015-12-26 1:30 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-12-26 1:25 U.Mutlu [this message]
2015-12-29 11:30 ` How to set DPOFUA=0 ? U.Mutlu
2015-12-29 11:43 ` Julian Calaby
2015-12-29 18:04 ` U.Mutlu
2016-01-19 20:50 ` Dmitry Katsubo
2016-01-19 22:10 ` Dmitry Katsubo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='n5kqb4$k8n$1@ger.gmane.org' \
--to=for-gmane@mutluit.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.