From: kaloz@openwrt.org (Imre Kaloz)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: OMAP2+: Use pdata quirks for wl12xx on the AM335x EV-MSK
Date: Tue, 25 Feb 2014 10:40:00 +0100 [thread overview]
Message-ID: <op.xbtzsyeh2s3iss@ecaz> (raw)
In-Reply-To: <1392806495-4874-1-git-send-email-kaloz@openwrt.org>
On Wed, 19 Feb 2014 11:41:35 +0100, Imre Kaloz <kaloz@openwrt.org> wrote:
> Enable the WiLink6 connected to mmc2.
>
> Signed-off-by: Imre Kaloz <kaloz@openwrt.org
> ---
> arch/arm/boot/dts/am335x-evmsk.dts | 40 ++++++++++++++++++++++++++++++++++++
> arch/arm/mach-omap2/pdata-quirks.c | 10 +++++++++
> 2 files changed, 50 insertions(+)
>
> diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
> index 4718ec4..a544fc4 100644
> --- a/arch/arm/boot/dts/am335x-evmsk.dts
> +++ b/arch/arm/boot/dts/am335x-evmsk.dts
> @@ -45,6 +45,18 @@
> regulator-boot-on;
> };
>+ wl12xx_vmmc: fixedregulator at 2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&wl12xx_gpio>;
> + compatible = "regulator-fixed";
> + regulator-name = "vwl1271";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&gpio1 29 0>;
> + startup-delay-us = <70000>;
> + enable-active-high;
> + };
> +
> leds {
> pinctrl-names = "default";
> pinctrl-0 = <&user_leds_s0>;
> @@ -264,6 +276,24 @@
> 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
> >;
> };
> +
> + mmc2_pins: pinmux_mmc2_pins {
> + pinctrl-single,pins = <
> + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */
> + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
> + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
> + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
> + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
> + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
> + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
> + >;
> + };
> +
> + wl12xx_gpio: pinmux_wl12xx_gpio {
> + pinctrl-single,pins = <
> + 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */
> + >;
> + };
> };
> &uart0 {
> @@ -470,6 +500,16 @@
> ti,no-reset-on-init;
> };
>+&mmc2 {
> + status = "okay";
> + vmmc-supply = <&wl12xx_vmmc>;
> + ti,non-removable;
> + bus-width = <4>;
> + cap-power-off-card;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_pins>;
> +};
> +
> &mcasp1 {
> pinctrl-names = "default";
> pinctrl-0 = <&mcasp1_pins>;
> diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
> index 3d5b24d..a92acdb 100644
> --- a/arch/arm/mach-omap2/pdata-quirks.c
> +++ b/arch/arm/mach-omap2/pdata-quirks.c
> @@ -187,6 +187,13 @@ static void __init omap4_panda_legacy_init(void)
> }
> #endif
>+#ifdef CONFIG_SOC_AM33XX
> +static void __init am335x_evmsk_legacy_init(void)
> +{
> + legacy_init_wl12xx(WL12XX_REFCLOCK_24, 0, 31);
> +}
> +#endif
> +
> #ifdef CONFIG_SOC_OMAP5
> static void __init omap5_uevm_legacy_init(void)
> {
> @@ -271,6 +278,9 @@ static struct pdata_init pdata_quirks[] __initdata = {
> { "ti,omap4-sdp", omap4_sdp_legacy_init, },
> { "ti,omap4-panda", omap4_panda_legacy_init, },
> #endif
> +#ifdef CONFIG_SOC_AM33XX
> + { "ti,am335x-evmsk", am335x_evmsk_legacy_init, },
> +#endif
> #ifdef CONFIG_SOC_OMAP5
> { "ti,omap5-uevm", omap5_uevm_legacy_init, },
> #endif
ping?
Imre
next prev parent reply other threads:[~2014-02-25 9:40 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-19 10:41 [PATCH] ARM: OMAP2+: Use pdata quirks for wl12xx on the AM335x EV-MSK Imre Kaloz
2014-02-25 9:40 ` Imre Kaloz [this message]
2014-02-28 22:54 ` Tony Lindgren
2014-02-28 23:11 ` Tony Lindgren
2014-03-03 8:46 ` Imre Kaloz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=op.xbtzsyeh2s3iss@ecaz \
--to=kaloz@openwrt.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.