From: sashiko-bot@kernel.org
To: "Michael Zaidman" <michael.zaidman@gmail.com>
Cc: linux-serial@vger.kernel.org
Subject: Re: [PATCH v4 10/16] HID: ft260: i2c: fix large write transaction failure
Date: Tue, 17 Nov 2026 20:30:12 +0000 [thread overview]
Message-ID: <sashiko-outbox-219609@kernel.org> (raw)
In-Reply-To: <20261117200423.19561-11-michael.zaidman@gmail.com>
> Fixes a regression from commit 5afac727defa ("HID: ft260: missed NACK
> from busy device"), which waited for bus-idle after every HID write
> report except when the report flag was exactly FT260_FLAG_START.
>
> Multi-report I2C writes keep the bus busy between chunks for atomicity.
> Treating those middle reports like a final STOP caused ft260_xfer_status()
> to spin on -EAGAIN after the second HID report and fail large writes.
> Write-then-read combined transfers still worked.
>
> Pass the bus-busy check policy from the caller: ft260_i2c_write() and
> ft260_smbus_write() wait for idle only when the report they send carries
> STOP; intermediate chunks and the command phase of a combined transfer
> do not.
>
> The SMBus side matters for register reads. The command phase is written
> [ ... ]
> Closes: https://github.com/MichaelZaidman/hid-ft260/issues/35
> Tested-by: Chris Keeser <chriskeeser@meta.com>
> Reported-by: Bruno Giacomazzi <brunoceg1@gmail.com>
> Closes: https://github.com/MichaelZaidman/hid-ft260/issues/42
> Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Sashiko has reviewed this patch and found no issues.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261117200423.19561-1-michael.zaidman@gmail.com?part=10
next prev parent reply other threads:[~2026-11-17 20:30 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-17 20:04 [PATCH v4 00/16] HID: ft260: add UART and GPIO support, plus I2C fixes Michael Zaidman
2026-11-17 20:04 ` [PATCH v4 01/16] HID: ft260: add serial driver Michael Zaidman
2026-11-17 20:32 ` sashiko-bot
2026-11-18 7:21 ` Jiri Slaby
2026-11-17 20:04 ` [PATCH v4 02/16] HID: ft260: uart: fix " Michael Zaidman
2026-11-17 20:49 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 03/16] HID: ft260: add GPIO support Michael Zaidman
2026-11-17 20:23 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 04/16] HID: ft260: i2c: reduce driver module loading time Michael Zaidman
2026-11-17 20:11 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 05/16] HID: ft260: fix sysfs store failure notice for big numbers Michael Zaidman
2026-11-17 20:12 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 06/16] HID: ft260: i2c: reduce bus-error message severity Michael Zaidman
2026-11-17 20:13 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 07/16] HID: ft260: uart: enable flow control Michael Zaidman
2026-11-17 20:21 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 08/16] HID: ft260: uart: add modem pins control via ioctl Michael Zaidman
2026-11-17 20:24 ` sashiko-bot
2026-11-17 23:56 ` Maarten Brock
2026-11-17 20:04 ` [PATCH v4 09/16] HID: ft260: group sysfs attrs per HID interface Michael Zaidman
2026-11-17 20:30 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 10/16] HID: ft260: i2c: fix large write transaction failure Michael Zaidman
2026-11-17 20:30 ` sashiko-bot [this message]
2026-11-17 20:04 ` [PATCH v4 11/16] HID: ft260: workaround for TN_189 errata endpoint STALL after enumeration Michael Zaidman
2026-11-17 20:50 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 12/16] HID: ft260: i2c: abort in-flight transfers with STOP before reset Michael Zaidman
2026-11-17 20:33 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 13/16] HID: ft260: i2c: reject an I2C clock outside the supported range Michael Zaidman
2026-11-17 20:34 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 14/16] HID: ft260: i2c: fix i2c_reset sysfs store return value Michael Zaidman
2026-11-17 20:35 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 15/16] HID: ft260: i2c: recover a bus held by a slave Michael Zaidman
2026-11-17 20:44 ` sashiko-bot
2026-11-17 20:04 ` [PATCH v4 16/16] HID: ft260: use lock guards Michael Zaidman
2026-11-17 20:36 ` sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-219609@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=michael.zaidman@gmail.com \
--cc=sashiko-reviews@lists.linux.dev \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.