[PATCH v3 00/11] OLPC Power Management

[PATCH v3 00/11] OLPC Power Management

[Daniel Drake]

Hi,

These patches implement various power management and system-level features
on the XO-1 and XO-1.5 laptops.

v2: add Acked-bys, add a code comment in response to review

v3: fix depends/select on MFD and CS5535 GPIO (from Andres)

Andrew, we're having trouble getting movement on these patches, would you
mind taking a quick look at them and maybe putting them in your tree?

Review comments very welcome, I'll do my best to act upon them quickly.

Thanks,
Daniel

[PATCH v3 01/11] x86, olpc: add missing elements to device tree

[Daniel Drake]

In response to new device tree code in the kernel, OLPC will start
using it for probing of certain devices. However, some firmware fixes
are needed to put the devicetree into a usable state.

Retain compatibility with old firmware by fixing up the device tree
at boot-time if it does not contain the new nodes/properties that
we need for probing. This is the same approach taken on PPC platforms.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: devicetree-discuss@lists.ozlabs.org
---
 arch/x86/platform/olpc/olpc_dt.c |  103 ++++++++++++++++++++++++++++++++++++++
 1 files changed, 103 insertions(+), 0 deletions(-)

diff --git a/arch/x86/platform/olpc/olpc_dt.c b/arch/x86/platform/olpc/olpc_dt.c
index d39f63d..d6ee929 100644
--- a/arch/x86/platform/olpc/olpc_dt.c
+++ b/arch/x86/platform/olpc/olpc_dt.c
@@ -165,6 +165,107 @@ static struct of_pdt_ops prom_olpc_ops __initdata = {
 	.pkg2path = olpc_dt_pkg2path,
 };
 
+static phandle __init olpc_dt_finddevice(const char *path)
+{
+	phandle node;
+	const void *args[] = { path };
+	void *res[] = { &node };
+
+	if (olpc_ofw("finddevice", args, res)) {
+		pr_err("olpc_dt: finddevice failed!\n");
+		return 0;
+	}
+
+	if ((s32) node == -1)
+		return 0;
+
+	return node;
+}
+
+static int __init olpc_dt_interpret(const char *words)
+{
+	int result;
+	const void *args[] = { words };
+	void *res[] = { &result };
+
+	if (olpc_ofw("interpret", args, res)) {
+		pr_err("olpc_dt: interpret failed!\n");
+		return -1;
+	}
+
+	return result;
+}
+
+/*
+ * Extract board revision directly from OFW device tree.
+ * We can't use olpc_platform_info because that hasn't been set up yet.
+ */
+static u32 __init olpc_dt_get_board_revision(void)
+{
+	phandle node;
+	__be32 rev;
+	int r;
+
+	node = olpc_dt_finddevice("/");
+	if (!node)
+		return 0;
+
+	r = olpc_dt_getproperty(node, "board-revision-int",
+				(char *) &rev, sizeof(rev));
+	if (r < 0)
+		return 0;
+
+	return be32_to_cpu(rev);
+}
+
+void __init olpc_dt_fixup(void)
+{
+	int r;
+	char buf[64];
+	phandle node;
+	u32 board_rev;
+
+	node = olpc_dt_finddevice("/battery@0");
+	if (!node)
+		return;
+
+	/*
+	 * If the battery node has a compatible property, we are running a new
+	 * enough firmware and don't have fixups to make.
+	 */
+	r = olpc_dt_getproperty(node, "compatible", buf, sizeof(buf));
+	if (r > 0)
+		return;
+
+	pr_info("PROM DT: Old firmware detected, applying fixes\n");
+
+	/* Add olpc,xo1-battery compatible marker to battery node */
+	olpc_dt_interpret("\" /battery@0\" find-device"
+		" \" olpc,xo1-battery\" +compatible"
+		" device-end");
+
+	board_rev = olpc_dt_get_board_revision();
+	if (!board_rev)
+		return;
+
+	if (board_rev >= olpc_board_pre(0xd0)) {
+		/* XO-1.5: add dcon device */
+		olpc_dt_interpret("\" /pci/display@1\" find-device"
+			" new-device"
+			" \" dcon\" device-name \" olpc,xo1-dcon\" +compatible"
+			" finish-device device-end");
+	} else {
+		/* XO-1: add dcon device, mark RTC as olpc,xo1-rtc */
+		olpc_dt_interpret("\" /pci/display@1,1\" find-device"
+			" new-device"
+			" \" dcon\" device-name \" olpc,xo1-dcon\" +compatible"
+			" finish-device device-end"
+			" \" /rtc\" find-device"
+			" \" olpc,xo1-rtc\" +compatible"
+			" device-end");
+	}
+}
+
 void __init olpc_dt_build_devicetree(void)
 {
 	phandle root;
@@ -172,6 +273,8 @@ void __init olpc_dt_build_devicetree(void)
 	if (!olpc_ofw_is_installed())
 		return;
 
+	olpc_dt_fixup();
+
 	root = olpc_dt_getsibling(0);
 	if (!root) {
 		pr_err("PROM: unable to get root node from OFW!\n");
-- 
1.7.5.4

[PATCH v3 01/11] x86, olpc: add missing elements to device tree

[Daniel Drake]

In response to new device tree code in the kernel, OLPC will start
using it for probing of certain devices. However, some firmware fixes
are needed to put the devicetree into a usable state.

Retain compatibility with old firmware by fixing up the device tree
at boot-time if it does not contain the new nodes/properties that
we need for probing. This is the same approach taken on PPC platforms.

Signed-off-by: Daniel Drake <dsd-2X9k7bc8m7Mdnm+yROfE0A@public.gmane.org>
Acked-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
Acked-by: Andres Salomon <dilinger-pFFUokh25LWsTnJN9+BGXg@public.gmane.org>
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org
---
 arch/x86/platform/olpc/olpc_dt.c |  103 ++++++++++++++++++++++++++++++++++++++
 1 files changed, 103 insertions(+), 0 deletions(-)

diff --git a/arch/x86/platform/olpc/olpc_dt.c b/arch/x86/platform/olpc/olpc_dt.c
index d39f63d..d6ee929 100644
--- a/arch/x86/platform/olpc/olpc_dt.c
+++ b/arch/x86/platform/olpc/olpc_dt.c
@@ -165,6 +165,107 @@ static struct of_pdt_ops prom_olpc_ops __initdata = {
 	.pkg2path = olpc_dt_pkg2path,
 };
 
+static phandle __init olpc_dt_finddevice(const char *path)
+{
+	phandle node;
+	const void *args[] = { path };
+	void *res[] = { &node };
+
+	if (olpc_ofw("finddevice", args, res)) {
+		pr_err("olpc_dt: finddevice failed!\n");
+		return 0;
+	}
+
+	if ((s32) node == -1)
+		return 0;
+
+	return node;
+}
+
+static int __init olpc_dt_interpret(const char *words)
+{
+	int result;
+	const void *args[] = { words };
+	void *res[] = { &result };
+
+	if (olpc_ofw("interpret", args, res)) {
+		pr_err("olpc_dt: interpret failed!\n");
+		return -1;
+	}
+
+	return result;
+}
+
+/*
+ * Extract board revision directly from OFW device tree.
+ * We can't use olpc_platform_info because that hasn't been set up yet.
+ */
+static u32 __init olpc_dt_get_board_revision(void)
+{
+	phandle node;
+	__be32 rev;
+	int r;
+
+	node = olpc_dt_finddevice("/");
+	if (!node)
+		return 0;
+
+	r = olpc_dt_getproperty(node, "board-revision-int",
+				(char *) &rev, sizeof(rev));
+	if (r < 0)
+		return 0;
+
+	return be32_to_cpu(rev);
+}
+
+void __init olpc_dt_fixup(void)
+{
+	int r;
+	char buf[64];
+	phandle node;
+	u32 board_rev;
+
+	node = olpc_dt_finddevice("/battery@0");
+	if (!node)
+		return;
+
+	/*
+	 * If the battery node has a compatible property, we are running a new
+	 * enough firmware and don't have fixups to make.
+	 */
+	r = olpc_dt_getproperty(node, "compatible", buf, sizeof(buf));
+	if (r > 0)
+		return;
+
+	pr_info("PROM DT: Old firmware detected, applying fixes\n");
+
+	/* Add olpc,xo1-battery compatible marker to battery node */
+	olpc_dt_interpret("\" /battery@0\" find-device"
+		" \" olpc,xo1-battery\" +compatible"
+		" device-end");
+
+	board_rev = olpc_dt_get_board_revision();
+	if (!board_rev)
+		return;
+
+	if (board_rev >= olpc_board_pre(0xd0)) {
+		/* XO-1.5: add dcon device */
+		olpc_dt_interpret("\" /pci/display@1\" find-device"
+			" new-device"
+			" \" dcon\" device-name \" olpc,xo1-dcon\" +compatible"
+			" finish-device device-end");
+	} else {
+		/* XO-1: add dcon device, mark RTC as olpc,xo1-rtc */
+		olpc_dt_interpret("\" /pci/display@1,1\" find-device"
+			" new-device"
+			" \" dcon\" device-name \" olpc,xo1-dcon\" +compatible"
+			" finish-device device-end"
+			" \" /rtc\" find-device"
+			" \" olpc,xo1-rtc\" +compatible"
+			" device-end");
+	}
+}
+
 void __init olpc_dt_build_devicetree(void)
 {
 	phandle root;
@@ -172,6 +273,8 @@ void __init olpc_dt_build_devicetree(void)
 	if (!olpc_ofw_is_installed())
 		return;
 
+	olpc_dt_fixup();
+
 	root = olpc_dt_getsibling(0);
 	if (!root) {
 		pr_err("PROM: unable to get root node from OFW!\n");
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Add missing elements to device tree

[tip-bot for Daniel Drake]

Commit-ID:  f70d8ef4745349000dc599b6873a8b866289c694
Gitweb:     http://git.kernel.org/tip/f70d8ef4745349000dc599b6873a8b866289c694
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:08 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:19 -0700

x86, olpc: Add missing elements to device tree

In response to new device tree code in the kernel, OLPC will start
using it for probing of certain devices. However, some firmware fixes
are needed to put the devicetree into a usable state.

Retain compatibility with old firmware by fixing up the device tree
at boot-time if it does not contain the new nodes/properties that
we need for probing. This is the same approach taken on PPC platforms.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-2-git-send-email-dsd@laptop.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/platform/olpc/olpc_dt.c |  103 ++++++++++++++++++++++++++++++++++++++
 1 files changed, 103 insertions(+), 0 deletions(-)

diff --git a/arch/x86/platform/olpc/olpc_dt.c b/arch/x86/platform/olpc/olpc_dt.c
index d39f63d..d6ee929 100644
--- a/arch/x86/platform/olpc/olpc_dt.c
+++ b/arch/x86/platform/olpc/olpc_dt.c
@@ -165,6 +165,107 @@ static struct of_pdt_ops prom_olpc_ops __initdata = {
 	.pkg2path = olpc_dt_pkg2path,
 };
 
+static phandle __init olpc_dt_finddevice(const char *path)
+{
+	phandle node;
+	const void *args[] = { path };
+	void *res[] = { &node };
+
+	if (olpc_ofw("finddevice", args, res)) {
+		pr_err("olpc_dt: finddevice failed!\n");
+		return 0;
+	}
+
+	if ((s32) node == -1)
+		return 0;
+
+	return node;
+}
+
+static int __init olpc_dt_interpret(const char *words)
+{
+	int result;
+	const void *args[] = { words };
+	void *res[] = { &result };
+
+	if (olpc_ofw("interpret", args, res)) {
+		pr_err("olpc_dt: interpret failed!\n");
+		return -1;
+	}
+
+	return result;
+}
+
+/*
+ * Extract board revision directly from OFW device tree.
+ * We can't use olpc_platform_info because that hasn't been set up yet.
+ */
+static u32 __init olpc_dt_get_board_revision(void)
+{
+	phandle node;
+	__be32 rev;
+	int r;
+
+	node = olpc_dt_finddevice("/");
+	if (!node)
+		return 0;
+
+	r = olpc_dt_getproperty(node, "board-revision-int",
+				(char *) &rev, sizeof(rev));
+	if (r < 0)
+		return 0;
+
+	return be32_to_cpu(rev);
+}
+
+void __init olpc_dt_fixup(void)
+{
+	int r;
+	char buf[64];
+	phandle node;
+	u32 board_rev;
+
+	node = olpc_dt_finddevice("/battery@0");
+	if (!node)
+		return;
+
+	/*
+	 * If the battery node has a compatible property, we are running a new
+	 * enough firmware and don't have fixups to make.
+	 */
+	r = olpc_dt_getproperty(node, "compatible", buf, sizeof(buf));
+	if (r > 0)
+		return;
+
+	pr_info("PROM DT: Old firmware detected, applying fixes\n");
+
+	/* Add olpc,xo1-battery compatible marker to battery node */
+	olpc_dt_interpret("\" /battery@0\" find-device"
+		" \" olpc,xo1-battery\" +compatible"
+		" device-end");
+
+	board_rev = olpc_dt_get_board_revision();
+	if (!board_rev)
+		return;
+
+	if (board_rev >= olpc_board_pre(0xd0)) {
+		/* XO-1.5: add dcon device */
+		olpc_dt_interpret("\" /pci/display@1\" find-device"
+			" new-device"
+			" \" dcon\" device-name \" olpc,xo1-dcon\" +compatible"
+			" finish-device device-end");
+	} else {
+		/* XO-1: add dcon device, mark RTC as olpc,xo1-rtc */
+		olpc_dt_interpret("\" /pci/display@1,1\" find-device"
+			" new-device"
+			" \" dcon\" device-name \" olpc,xo1-dcon\" +compatible"
+			" finish-device device-end"
+			" \" /rtc\" find-device"
+			" \" olpc,xo1-rtc\" +compatible"
+			" device-end");
+	}
+}
+
 void __init olpc_dt_build_devicetree(void)
 {
 	phandle root;
@@ -172,6 +273,8 @@ void __init olpc_dt_build_devicetree(void)
 	if (!olpc_ofw_is_installed())
 		return;
 
+	olpc_dt_fixup();
+
 	root = olpc_dt_getsibling(0);
 	if (!root) {
 		pr_err("PROM: unable to get root node from OFW!\n");

[PATCH v3 02/11] x86, olpc: Move CS5536-related constants to cs5535.h

[Daniel Drake]

Move these definitions into the relevant header file.
This was requested in the review of the upcoming XO-1 suspend/resume code.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/platform/olpc/olpc-xo1.c |   26 ++++++++------------------
 include/linux/cs5535.h            |   21 +++++++++++++++++++++
 2 files changed, 29 insertions(+), 18 deletions(-)

diff --git a/arch/x86/platform/olpc/olpc-xo1.c b/arch/x86/platform/olpc/olpc-xo1.c
index ab81fb2..a63e948 100644
--- a/arch/x86/platform/olpc/olpc-xo1.c
+++ b/arch/x86/platform/olpc/olpc-xo1.c
@@ -12,6 +12,7 @@
  * (at your option) any later version.
  */
 
+#include <linux/cs5535.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
@@ -22,17 +23,6 @@
 
 #define DRV_NAME "olpc-xo1"
 
-/* PMC registers (PMS block) */
-#define PM_SCLK		0x10
-#define PM_IN_SLPCTL	0x20
-#define PM_WKXD		0x34
-#define PM_WKD		0x30
-#define PM_SSC		0x54
-
-/* PM registers (ACPI block) */
-#define PM1_CNT		0x08
-#define PM_GPE0_STS	0x18
-
 static unsigned long acpi_base;
 static unsigned long pms_base;
 
@@ -41,17 +31,17 @@ static void xo1_power_off(void)
 	printk(KERN_INFO "OLPC XO-1 power off sequence...\n");
 
 	/* Enable all of these controls with 0 delay */
-	outl(0x40000000, pms_base + PM_SCLK);
-	outl(0x40000000, pms_base + PM_IN_SLPCTL);
-	outl(0x40000000, pms_base + PM_WKXD);
-	outl(0x40000000, pms_base + PM_WKD);
+	outl(0x40000000, pms_base + CS5536_PM_SCLK);
+	outl(0x40000000, pms_base + CS5536_PM_IN_SLPCTL);
+	outl(0x40000000, pms_base + CS5536_PM_WKXD);
+	outl(0x40000000, pms_base + CS5536_PM_WKD);
 
 	/* Clear status bits (possibly unnecessary) */
-	outl(0x0002ffff, pms_base  + PM_SSC);
-	outl(0xffffffff, acpi_base + PM_GPE0_STS);
+	outl(0x0002ffff, pms_base  + CS5536_PM_SSC);
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
 
 	/* Write SLP_EN bit to start the machinery */
-	outl(0x00002000, acpi_base + PM1_CNT);
+	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
 }
 
 static int __devinit olpc_xo1_probe(struct platform_device *pdev)
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 6fe2114..e46b8b0 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -49,6 +49,27 @@
 #define LBAR_ACPI_SIZE		0x40
 #define LBAR_PMS_SIZE		0x80
 
+/*
+ * PMC registers (PMS block)
+ * It is only safe to access these registers as dword accesses.
+ * See CS5536 Specification Update erratas 17 & 18
+ */
+#define CS5536_PM_SCLK		0x10
+#define CS5536_PM_IN_SLPCTL	0x20
+#define CS5536_PM_WKXD		0x34
+#define CS5536_PM_WKD		0x30
+#define CS5536_PM_SSC		0x54
+
+/*
+ * PM registers (ACPI block)
+ * It is only safe to access these registers as dword accesses.
+ * See CS5536 Specification Update erratas 17 & 18
+ */
+#define CS5536_PM1_STS		0x00
+#define CS5536_PM1_EN		0x02
+#define CS5536_PM1_CNT		0x08
+#define CS5536_PM_GPE0_STS	0x18
+
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
 #define VSA_VRC_DATA		0xAC1E
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Move CS5536-related constants to cs5535.h

[tip-bot for Daniel Drake]

Commit-ID:  7a0d4fcf6d4b80b30503fd2701eeef1883e11404
Gitweb:     http://git.kernel.org/tip/7a0d4fcf6d4b80b30503fd2701eeef1883e11404
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:09 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:23 -0700

x86, olpc: Move CS5536-related constants to cs5535.h

Move these definitions into the relevant header file.
This was requested in the review of the upcoming XO-1 suspend/resume code.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-3-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/platform/olpc/olpc-xo1.c |   26 ++++++++------------------
 include/linux/cs5535.h            |   21 +++++++++++++++++++++
 2 files changed, 29 insertions(+), 18 deletions(-)

diff --git a/arch/x86/platform/olpc/olpc-xo1.c b/arch/x86/platform/olpc/olpc-xo1.c
index ab81fb2..a63e948 100644
--- a/arch/x86/platform/olpc/olpc-xo1.c
+++ b/arch/x86/platform/olpc/olpc-xo1.c
@@ -12,6 +12,7 @@
  * (at your option) any later version.
  */
 
+#include <linux/cs5535.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
@@ -22,17 +23,6 @@
 
 #define DRV_NAME "olpc-xo1"
 
-/* PMC registers (PMS block) */
-#define PM_SCLK		0x10
-#define PM_IN_SLPCTL	0x20
-#define PM_WKXD		0x34
-#define PM_WKD		0x30
-#define PM_SSC		0x54
-
-/* PM registers (ACPI block) */
-#define PM1_CNT		0x08
-#define PM_GPE0_STS	0x18
-
 static unsigned long acpi_base;
 static unsigned long pms_base;
 
@@ -41,17 +31,17 @@ static void xo1_power_off(void)
 	printk(KERN_INFO "OLPC XO-1 power off sequence...\n");
 
 	/* Enable all of these controls with 0 delay */
-	outl(0x40000000, pms_base + PM_SCLK);
-	outl(0x40000000, pms_base + PM_IN_SLPCTL);
-	outl(0x40000000, pms_base + PM_WKXD);
-	outl(0x40000000, pms_base + PM_WKD);
+	outl(0x40000000, pms_base + CS5536_PM_SCLK);
+	outl(0x40000000, pms_base + CS5536_PM_IN_SLPCTL);
+	outl(0x40000000, pms_base + CS5536_PM_WKXD);
+	outl(0x40000000, pms_base + CS5536_PM_WKD);
 
 	/* Clear status bits (possibly unnecessary) */
-	outl(0x0002ffff, pms_base  + PM_SSC);
-	outl(0xffffffff, acpi_base + PM_GPE0_STS);
+	outl(0x0002ffff, pms_base  + CS5536_PM_SSC);
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
 
 	/* Write SLP_EN bit to start the machinery */
-	outl(0x00002000, acpi_base + PM1_CNT);
+	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
 }
 
 static int __devinit olpc_xo1_probe(struct platform_device *pdev)
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 6fe2114..e46b8b0 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -49,6 +49,27 @@
 #define LBAR_ACPI_SIZE		0x40
 #define LBAR_PMS_SIZE		0x80
 
+/*
+ * PMC registers (PMS block)
+ * It is only safe to access these registers as dword accesses.
+ * See CS5536 Specification Update erratas 17 & 18
+ */
+#define CS5536_PM_SCLK		0x10
+#define CS5536_PM_IN_SLPCTL	0x20
+#define CS5536_PM_WKXD		0x34
+#define CS5536_PM_WKD		0x30
+#define CS5536_PM_SSC		0x54
+
+/*
+ * PM registers (ACPI block)
+ * It is only safe to access these registers as dword accesses.
+ * See CS5536 Specification Update erratas 17 & 18
+ */
+#define CS5536_PM1_STS		0x00
+#define CS5536_PM1_EN		0x02
+#define CS5536_PM1_CNT		0x08
+#define CS5536_PM_GPE0_STS	0x18
+
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
 #define VSA_VRC_DATA		0xAC1E

[PATCH v3 03/11] x86, olpc: rename olpc-xo1 to olpc-xo1-pm

[Daniel Drake]

Based on earlier review comments, we'll no longer try to stick all of
our XO-1 goodies in a single driver. We'll split it into a power management
driver, and an EC/SCI driver.

As a first step, rename olpc-xo1 to olpc-xo1-pm, and make it builtin
instead of modular.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                     |    7 +-
 arch/x86/platform/olpc/Makefile      |    2 +-
 arch/x86/platform/olpc/olpc-xo1-pm.c |  123 ++++++++++++++++++++++++++++++
 arch/x86/platform/olpc/olpc-xo1.c    |  136 ----------------------------------
 4 files changed, 128 insertions(+), 140 deletions(-)
 create mode 100644 arch/x86/platform/olpc/olpc-xo1-pm.c
 delete mode 100644 arch/x86/platform/olpc/olpc-xo1.c

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 26a14b4..e7851be 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2075,11 +2075,12 @@ config OLPC
 	  Add support for detecting the unique features of the OLPC
 	  XO hardware.
 
-config OLPC_XO1
-	tristate "OLPC XO-1 support"
+config OLPC_XO1_PM
+	bool "OLPC XO-1 Power Management"
 	depends on OLPC && MFD_CS5535
+	select MFD_CORE
 	---help---
-	  Add support for non-essential features of the OLPC XO-1 laptop.
+	  Add support for poweroff of the OLPC XO-1 laptop.
 
 endif # X86_32
 
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 81c5e21..cd25038 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,2 +1,2 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
-obj-$(CONFIG_OLPC_XO1)		+= olpc-xo1.o
+obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-pm.c b/arch/x86/platform/olpc/olpc-xo1-pm.c
new file mode 100644
index 0000000..a2a59d3
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo1-pm.c
@@ -0,0 +1,123 @@
+/*
+ * Support for power management features of the OLPC XO-1 laptop
+ *
+ * Copyright (C) 2010 Andres Salomon <dilinger@queued.net>
+ * Copyright (C) 2010 One Laptop per Child
+ * Copyright (C) 2006 Red Hat, Inc.
+ * Copyright (C) 2006 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/cs5535.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/mfd/core.h>
+
+#include <asm/io.h>
+#include <asm/olpc.h>
+
+#define DRV_NAME "olpc-xo1-pm"
+
+static unsigned long acpi_base;
+static unsigned long pms_base;
+
+static void xo1_power_off(void)
+{
+	printk(KERN_INFO "OLPC XO-1 power off sequence...\n");
+
+	/* Enable all of these controls with 0 delay */
+	outl(0x40000000, pms_base + CS5536_PM_SCLK);
+	outl(0x40000000, pms_base + CS5536_PM_IN_SLPCTL);
+	outl(0x40000000, pms_base + CS5536_PM_WKXD);
+	outl(0x40000000, pms_base + CS5536_PM_WKD);
+
+	/* Clear status bits (possibly unnecessary) */
+	outl(0x0002ffff, pms_base  + CS5536_PM_SSC);
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
+
+	/* Write SLP_EN bit to start the machinery */
+	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
+}
+
+static int __devinit xo1_pm_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	int err;
+
+	/* don't run on non-XOs */
+	if (!machine_is_olpc())
+		return -ENODEV;
+
+	err = mfd_cell_enable(pdev);
+	if (err)
+		return err;
+
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "can't fetch device resource info\n");
+		return -EIO;
+	}
+	if (strcmp(pdev->name, "cs5535-pms") == 0)
+		pms_base = res->start;
+	else if (strcmp(pdev->name, "olpc-xo1-pm-acpi") == 0)
+		acpi_base = res->start;
+
+	/* If we have both addresses, we can override the poweroff hook */
+	if (pms_base && acpi_base) {
+		pm_power_off = xo1_power_off;
+		printk(KERN_INFO "OLPC XO-1 support registered\n");
+	}
+
+	return 0;
+}
+
+static int __devexit xo1_pm_remove(struct platform_device *pdev)
+{
+	mfd_cell_disable(pdev);
+
+	if (strcmp(pdev->name, "cs5535-pms") == 0)
+		pms_base = 0;
+	else if (strcmp(pdev->name, "olpc-xo1-pm-acpi") == 0)
+		acpi_base = 0;
+
+	pm_power_off = NULL;
+	return 0;
+}
+
+static struct platform_driver cs5535_pms_driver = {
+	.driver = {
+		.name = "cs5535-pms",
+		.owner = THIS_MODULE,
+	},
+	.probe = xo1_pm_probe,
+	.remove = __devexit_p(xo1_pm_remove),
+};
+
+static struct platform_driver cs5535_acpi_driver = {
+	.driver = {
+		.name = "olpc-xo1-pm-acpi",
+		.owner = THIS_MODULE,
+	},
+	.probe = xo1_pm_probe,
+	.remove = __devexit_p(xo1_pm_remove),
+};
+
+static int __init xo1_pm_init(void)
+{
+	int r;
+
+	r = platform_driver_register(&cs5535_pms_driver);
+	if (r)
+		return r;
+
+	r = platform_driver_register(&cs5535_acpi_driver);
+	if (r)
+		platform_driver_unregister(&cs5535_pms_driver);
+
+	return r;
+}
+arch_initcall(xo1_pm_init);
diff --git a/arch/x86/platform/olpc/olpc-xo1.c b/arch/x86/platform/olpc/olpc-xo1.c
deleted file mode 100644
index a63e948..0000000
--- a/arch/x86/platform/olpc/olpc-xo1.c
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * Support for features of the OLPC XO-1 laptop
- *
- * Copyright (C) 2010 Andres Salomon <dilinger@queued.net>
- * Copyright (C) 2010 One Laptop per Child
- * Copyright (C) 2006 Red Hat, Inc.
- * Copyright (C) 2006 Advanced Micro Devices, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/cs5535.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/pm.h>
-#include <linux/mfd/core.h>
-
-#include <asm/io.h>
-#include <asm/olpc.h>
-
-#define DRV_NAME "olpc-xo1"
-
-static unsigned long acpi_base;
-static unsigned long pms_base;
-
-static void xo1_power_off(void)
-{
-	printk(KERN_INFO "OLPC XO-1 power off sequence...\n");
-
-	/* Enable all of these controls with 0 delay */
-	outl(0x40000000, pms_base + CS5536_PM_SCLK);
-	outl(0x40000000, pms_base + CS5536_PM_IN_SLPCTL);
-	outl(0x40000000, pms_base + CS5536_PM_WKXD);
-	outl(0x40000000, pms_base + CS5536_PM_WKD);
-
-	/* Clear status bits (possibly unnecessary) */
-	outl(0x0002ffff, pms_base  + CS5536_PM_SSC);
-	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
-
-	/* Write SLP_EN bit to start the machinery */
-	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
-}
-
-static int __devinit olpc_xo1_probe(struct platform_device *pdev)
-{
-	struct resource *res;
-	int err;
-
-	/* don't run on non-XOs */
-	if (!machine_is_olpc())
-		return -ENODEV;
-
-	err = mfd_cell_enable(pdev);
-	if (err)
-		return err;
-
-	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "can't fetch device resource info\n");
-		return -EIO;
-	}
-	if (strcmp(pdev->name, "cs5535-pms") == 0)
-		pms_base = res->start;
-	else if (strcmp(pdev->name, "olpc-xo1-pm-acpi") == 0)
-		acpi_base = res->start;
-
-	/* If we have both addresses, we can override the poweroff hook */
-	if (pms_base && acpi_base) {
-		pm_power_off = xo1_power_off;
-		printk(KERN_INFO "OLPC XO-1 support registered\n");
-	}
-
-	return 0;
-}
-
-static int __devexit olpc_xo1_remove(struct platform_device *pdev)
-{
-	mfd_cell_disable(pdev);
-
-	if (strcmp(pdev->name, "cs5535-pms") == 0)
-		pms_base = 0;
-	else if (strcmp(pdev->name, "olpc-xo1-pm-acpi") == 0)
-		acpi_base = 0;
-
-	pm_power_off = NULL;
-	return 0;
-}
-
-static struct platform_driver cs5535_pms_drv = {
-	.driver = {
-		.name = "cs5535-pms",
-		.owner = THIS_MODULE,
-	},
-	.probe = olpc_xo1_probe,
-	.remove = __devexit_p(olpc_xo1_remove),
-};
-
-static struct platform_driver cs5535_acpi_drv = {
-	.driver = {
-		.name = "olpc-xo1-pm-acpi",
-		.owner = THIS_MODULE,
-	},
-	.probe = olpc_xo1_probe,
-	.remove = __devexit_p(olpc_xo1_remove),
-};
-
-static int __init olpc_xo1_init(void)
-{
-	int r;
-
-	r = platform_driver_register(&cs5535_pms_drv);
-	if (r)
-		return r;
-
-	r = platform_driver_register(&cs5535_acpi_drv);
-	if (r)
-		platform_driver_unregister(&cs5535_pms_drv);
-
-	return r;
-}
-
-static void __exit olpc_xo1_exit(void)
-{
-	platform_driver_unregister(&cs5535_acpi_drv);
-	platform_driver_unregister(&cs5535_pms_drv);
-}
-
-MODULE_AUTHOR("Daniel Drake <dsd@laptop.org>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:cs5535-pms");
-
-module_init(olpc_xo1_init);
-module_exit(olpc_xo1_exit);
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Rename olpc-xo1 to olpc-xo1-pm

[tip-bot for Daniel Drake]

Commit-ID:  a3128588b3c6be634a9013a375903e0b55668f0a
Gitweb:     http://git.kernel.org/tip/a3128588b3c6be634a9013a375903e0b55668f0a
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:10 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:28 -0700

x86, olpc: Rename olpc-xo1 to olpc-xo1-pm

Based on earlier review comments, we'll no longer try to stick all of
our XO-1 goodies in a single driver. We'll split it into a power management
driver, and an EC/SCI driver.

As a first step, rename olpc-xo1 to olpc-xo1-pm, and make it builtin
instead of modular.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-4-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                                   |    7 ++-
 arch/x86/platform/olpc/Makefile                    |    2 +-
 .../platform/olpc/{olpc-xo1.c => olpc-xo1-pm.c}    |   43 +++++++-------------
 3 files changed, 20 insertions(+), 32 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index da34972..29615ee 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2073,11 +2073,12 @@ config OLPC
 	  Add support for detecting the unique features of the OLPC
 	  XO hardware.
 
-config OLPC_XO1
-	tristate "OLPC XO-1 support"
+config OLPC_XO1_PM
+	bool "OLPC XO-1 Power Management"
 	depends on OLPC && MFD_CS5535
+	select MFD_CORE
 	---help---
-	  Add support for non-essential features of the OLPC XO-1 laptop.
+	  Add support for poweroff of the OLPC XO-1 laptop.
 
 endif # X86_32
 
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 81c5e21..cd25038 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,2 +1,2 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
-obj-$(CONFIG_OLPC_XO1)		+= olpc-xo1.o
+obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o
diff --git a/arch/x86/platform/olpc/olpc-xo1.c b/arch/x86/platform/olpc/olpc-xo1-pm.c
similarity index 70%
rename from arch/x86/platform/olpc/olpc-xo1.c
rename to arch/x86/platform/olpc/olpc-xo1-pm.c
index a63e948..a2a59d3 100644
--- a/arch/x86/platform/olpc/olpc-xo1.c
+++ b/arch/x86/platform/olpc/olpc-xo1-pm.c
@@ -1,5 +1,5 @@
 /*
- * Support for features of the OLPC XO-1 laptop
+ * Support for power management features of the OLPC XO-1 laptop
  *
  * Copyright (C) 2010 Andres Salomon <dilinger@queued.net>
  * Copyright (C) 2010 One Laptop per Child
@@ -13,7 +13,6 @@
  */
 
 #include <linux/cs5535.h>
-#include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
@@ -21,7 +20,7 @@
 #include <asm/io.h>
 #include <asm/olpc.h>
 
-#define DRV_NAME "olpc-xo1"
+#define DRV_NAME "olpc-xo1-pm"
 
 static unsigned long acpi_base;
 static unsigned long pms_base;
@@ -44,7 +43,7 @@ static void xo1_power_off(void)
 	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
 }
 
-static int __devinit olpc_xo1_probe(struct platform_device *pdev)
+static int __devinit xo1_pm_probe(struct platform_device *pdev)
 {
 	struct resource *res;
 	int err;
@@ -76,7 +75,7 @@ static int __devinit olpc_xo1_probe(struct platform_device *pdev)
 	return 0;
 }
 
-static int __devexit olpc_xo1_remove(struct platform_device *pdev)
+static int __devexit xo1_pm_remove(struct platform_device *pdev)
 {
 	mfd_cell_disable(pdev);
 
@@ -89,48 +88,36 @@ static int __devexit olpc_xo1_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static struct platform_driver cs5535_pms_drv = {
+static struct platform_driver cs5535_pms_driver = {
 	.driver = {
 		.name = "cs5535-pms",
 		.owner = THIS_MODULE,
 	},
-	.probe = olpc_xo1_probe,
-	.remove = __devexit_p(olpc_xo1_remove),
+	.probe = xo1_pm_probe,
+	.remove = __devexit_p(xo1_pm_remove),
 };
 
-static struct platform_driver cs5535_acpi_drv = {
+static struct platform_driver cs5535_acpi_driver = {
 	.driver = {
 		.name = "olpc-xo1-pm-acpi",
 		.owner = THIS_MODULE,
 	},
-	.probe = olpc_xo1_probe,
-	.remove = __devexit_p(olpc_xo1_remove),
+	.probe = xo1_pm_probe,
+	.remove = __devexit_p(xo1_pm_remove),
 };
 
-static int __init olpc_xo1_init(void)
+static int __init xo1_pm_init(void)
 {
 	int r;
 
-	r = platform_driver_register(&cs5535_pms_drv);
+	r = platform_driver_register(&cs5535_pms_driver);
 	if (r)
 		return r;
 
-	r = platform_driver_register(&cs5535_acpi_drv);
+	r = platform_driver_register(&cs5535_acpi_driver);
 	if (r)
-		platform_driver_unregister(&cs5535_pms_drv);
+		platform_driver_unregister(&cs5535_pms_driver);
 
 	return r;
 }
-
-static void __exit olpc_xo1_exit(void)
-{
-	platform_driver_unregister(&cs5535_acpi_drv);
-	platform_driver_unregister(&cs5535_pms_drv);
-}
-
-MODULE_AUTHOR("Daniel Drake <dsd@laptop.org>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:cs5535-pms");
-
-module_init(olpc_xo1_init);
-module_exit(olpc_xo1_exit);
+arch_initcall(xo1_pm_init);

[PATCH v3 04/11] x86, olpc: Add XO-1 suspend/resume support

[Daniel Drake]

Add code needed for basic suspend/resume of the XO-1 laptop.
Based on earlier work by Jordan Crouse, Andres Salomon, and others.

This patch incorporates all earlier feedback from Thomas Gleixner. To
clarify a certain point (now more obvious in the code itself):
On resume, OpenFirmware returns execution to Linux in protected mode
with a kernel-compatible GDT already set up. The changes and
simplifications suggested have all been included.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                     |    4 +-
 arch/x86/include/asm/olpc.h          |   15 +++-
 arch/x86/platform/olpc/Makefile      |    2 +-
 arch/x86/platform/olpc/olpc-xo1-pm.c |   92 +++++++++++++++++++++++++
 arch/x86/platform/olpc/xo1-wakeup.S  |  124 ++++++++++++++++++++++++++++++++++
 include/linux/cs5535.h               |    3 +
 6 files changed, 234 insertions(+), 6 deletions(-)
 create mode 100644 arch/x86/platform/olpc/xo1-wakeup.S

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index e7851be..a9953bf 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2077,10 +2077,10 @@ config OLPC
 
 config OLPC_XO1_PM
 	bool "OLPC XO-1 Power Management"
-	depends on OLPC && MFD_CS5535
+	depends on OLPC && MFD_CS5535 && PM_SLEEP
 	select MFD_CORE
 	---help---
-	  Add support for poweroff of the OLPC XO-1 laptop.
+	  Add support for poweroff and suspend of the OLPC XO-1 laptop.
 
 endif # X86_32
 
diff --git a/arch/x86/include/asm/olpc.h b/arch/x86/include/asm/olpc.h
index 5ca6801..10ea595 100644
--- a/arch/x86/include/asm/olpc.h
+++ b/arch/x86/include/asm/olpc.h
@@ -76,6 +76,12 @@ static inline int olpc_has_dcon(void)
 
 #endif
 
+#ifdef CONFIG_OLPC_XO1_PM
+extern void do_olpc_suspend_lowlevel(void);
+extern void olpc_xo1_pm_wakeup_set(u16 value);
+extern void olpc_xo1_pm_wakeup_clear(u16 value);
+#endif
+
 extern int pci_olpc_init(void);
 
 /* EC related functions */
@@ -88,9 +94,12 @@ extern int olpc_ec_mask_unset(uint8_t bits);
 
 /* EC commands */
 
-#define EC_FIRMWARE_REV		0x08
-#define EC_WLAN_ENTER_RESET	0x35
-#define EC_WLAN_LEAVE_RESET	0x25
+#define EC_FIRMWARE_REV			0x08
+#define EC_WAKE_UP_WLAN			0x24
+#define EC_WLAN_LEAVE_RESET		0x25
+#define EC_SET_SCI_INHIBIT		0x32
+#define EC_SET_SCI_INHIBIT_RELEASE	0x34
+#define EC_WLAN_ENTER_RESET		0x35
 
 /* SCI source values */
 
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index cd25038..1ae7bed 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,2 +1,2 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
-obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o
+obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-pm.c b/arch/x86/platform/olpc/olpc-xo1-pm.c
index a2a59d3..6f3855a 100644
--- a/arch/x86/platform/olpc/olpc-xo1-pm.c
+++ b/arch/x86/platform/olpc/olpc-xo1-pm.c
@@ -16,6 +16,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
+#include <linux/suspend.h>
 
 #include <asm/io.h>
 #include <asm/olpc.h>
@@ -25,6 +26,85 @@
 static unsigned long acpi_base;
 static unsigned long pms_base;
 
+static u16 wakeup_mask = CS5536_PM_PWRBTN;
+
+static struct {
+	unsigned long address;
+	unsigned short segment;
+} ofw_bios_entry = { 0xF0000 + PAGE_OFFSET, __KERNEL_CS };
+
+/* Set bits in the wakeup mask */
+void olpc_xo1_pm_wakeup_set(u16 value)
+{
+	wakeup_mask |= value;
+}
+EXPORT_SYMBOL_GPL(olpc_xo1_pm_wakeup_set);
+
+/* Clear bits in the wakeup mask */
+void olpc_xo1_pm_wakeup_clear(u16 value)
+{
+	wakeup_mask &= ~value;
+}
+EXPORT_SYMBOL_GPL(olpc_xo1_pm_wakeup_clear);
+
+static int xo1_power_state_enter(suspend_state_t pm_state)
+{
+	unsigned long saved_sci_mask;
+	int r;
+
+	/* Only STR is supported */
+	if (pm_state != PM_SUSPEND_MEM)
+		return -EINVAL;
+
+	r = olpc_ec_cmd(EC_SET_SCI_INHIBIT, NULL, 0, NULL, 0);
+	if (r)
+		return r;
+
+	/*
+	 * Save SCI mask (this gets lost since PM1_EN is used as a mask for
+	 * wakeup events, which is not necessarily the same event set)
+	 */
+	saved_sci_mask = inl(acpi_base + CS5536_PM1_STS);
+	saved_sci_mask &= 0xffff0000;
+
+	/* Save CPU state */
+	do_olpc_suspend_lowlevel();
+
+	/* Resume path starts here */
+
+	/* Restore SCI mask (using dword access to CS5536_PM1_EN) */
+	outl(saved_sci_mask, acpi_base + CS5536_PM1_STS);
+
+	/* Tell the EC to stop inhibiting SCIs */
+	olpc_ec_cmd(EC_SET_SCI_INHIBIT_RELEASE, NULL, 0, NULL, 0);
+
+	/*
+	 * Tell the wireless module to restart USB communication.
+	 * Must be done twice.
+	 */
+	olpc_ec_cmd(EC_WAKE_UP_WLAN, NULL, 0, NULL, 0);
+	olpc_ec_cmd(EC_WAKE_UP_WLAN, NULL, 0, NULL, 0);
+
+	return 0;
+}
+
+asmlinkage int xo1_do_sleep(u8 sleep_state)
+{
+	void *pgd_addr = __va(read_cr3());
+
+	/* Program wakeup mask (using dword access to CS5536_PM1_EN) */
+	outl(wakeup_mask << 16, acpi_base + CS5536_PM1_STS);
+
+	__asm__("movl %0,%%eax" : : "r" (pgd_addr));
+	__asm__("call *(%%edi); cld"
+		: : "D" (&ofw_bios_entry));
+	__asm__("movb $0x34, %al\n\t"
+		"outb %al, $0x70\n\t"
+		"movb $0x30, %al\n\t"
+		"outb %al, $0x71\n\t");
+	return 0;
+}
+
 static void xo1_power_off(void)
 {
 	printk(KERN_INFO "OLPC XO-1 power off sequence...\n");
@@ -43,6 +123,17 @@ static void xo1_power_off(void)
 	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
 }
 
+static int xo1_power_state_valid(suspend_state_t pm_state)
+{
+	/* suspend-to-RAM only */
+	return pm_state == PM_SUSPEND_MEM;
+}
+
+static const struct platform_suspend_ops xo1_suspend_ops = {
+	.valid = xo1_power_state_valid,
+	.enter = xo1_power_state_enter,
+};
+
 static int __devinit xo1_pm_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -68,6 +159,7 @@ static int __devinit xo1_pm_probe(struct platform_device *pdev)
 
 	/* If we have both addresses, we can override the poweroff hook */
 	if (pms_base && acpi_base) {
+		suspend_set_ops(&xo1_suspend_ops);
 		pm_power_off = xo1_power_off;
 		printk(KERN_INFO "OLPC XO-1 support registered\n");
 	}
diff --git a/arch/x86/platform/olpc/xo1-wakeup.S b/arch/x86/platform/olpc/xo1-wakeup.S
new file mode 100644
index 0000000..948deb2
--- /dev/null
+++ b/arch/x86/platform/olpc/xo1-wakeup.S
@@ -0,0 +1,124 @@
+.text
+#include <linux/linkage.h>
+#include <asm/segment.h>
+#include <asm/page.h>
+#include <asm/pgtable_32.h>
+
+	.macro writepost,value
+		movb $0x34, %al
+		outb %al, $0x70
+		movb $\value, %al
+		outb %al, $0x71
+	.endm
+
+wakeup_start:
+	# OFW lands us here, running in protected mode, with a
+	# kernel-compatible GDT already setup.
+
+	# Clear any dangerous flags
+	pushl $0
+	popfl
+
+	writepost 0x31
+
+	# Set up %cr3
+	movl $initial_page_table - __PAGE_OFFSET, %eax
+	movl %eax, %cr3
+
+	movl saved_cr4, %eax
+	movl %eax, %cr4
+
+	movl saved_cr0, %eax
+	movl %eax, %cr0
+
+	# Control registers were modified, pipeline resync is needed
+	jmp 1f
+1:
+
+	movw    $__KERNEL_DS, %ax
+	movw    %ax, %ss
+	movw    %ax, %ds
+	movw    %ax, %es
+	movw    %ax, %fs
+	movw    %ax, %gs
+
+	lgdt    saved_gdt
+	lidt    saved_idt
+	lldt    saved_ldt
+	ljmp    $(__KERNEL_CS),$1f
+1:
+	movl    %cr3, %eax
+	movl    %eax, %cr3
+	wbinvd
+
+	# Go back to the return point
+	jmp ret_point
+
+save_registers:
+	sgdt  saved_gdt
+	sidt  saved_idt
+	sldt  saved_ldt
+
+	pushl %edx
+	movl %cr4, %edx
+	movl %edx, saved_cr4
+
+	movl %cr0, %edx
+	movl %edx, saved_cr0
+
+	popl %edx
+
+	movl %ebx, saved_context_ebx
+	movl %ebp, saved_context_ebp
+	movl %esi, saved_context_esi
+	movl %edi, saved_context_edi
+
+	pushfl
+	popl saved_context_eflags
+
+	ret
+
+restore_registers:
+	movl saved_context_ebp, %ebp
+	movl saved_context_ebx, %ebx
+	movl saved_context_esi, %esi
+	movl saved_context_edi, %edi
+
+	pushl saved_context_eflags
+	popfl
+
+	ret
+
+ENTRY(do_olpc_suspend_lowlevel)
+	call	save_processor_state
+	call	save_registers
+
+	# This is the stack context we want to remember
+	movl %esp, saved_context_esp
+
+	pushl	$3
+	call	xo1_do_sleep
+
+	jmp	wakeup_start
+	.p2align 4,,7
+ret_point:
+	movl    saved_context_esp, %esp
+
+	writepost 0x32
+
+	call	restore_registers
+	call	restore_processor_state
+	ret
+
+.data
+saved_gdt:             .long   0,0
+saved_idt:             .long   0,0
+saved_ldt:             .long   0
+saved_cr4:             .long   0
+saved_cr0:             .long   0
+saved_context_esp:     .long   0
+saved_context_edi:     .long   0
+saved_context_esi:     .long   0
+saved_context_ebx:     .long   0
+saved_context_ebp:     .long   0
+saved_context_eflags:  .long   0
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index e46b8b0..2facf16 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -70,6 +70,9 @@
 #define CS5536_PM1_CNT		0x08
 #define CS5536_PM_GPE0_STS	0x18
 
+/* CS5536_PM1_EN bits */
+#define CS5536_PM_PWRBTN	(1 << 8)
+
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
 #define VSA_VRC_DATA		0xAC1E
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Add XO-1 suspend/resume support

[tip-bot for Daniel Drake]

Commit-ID:  97c4cb71c18fe045a763ff6681a8ebbbbbec0b2b
Gitweb:     http://git.kernel.org/tip/97c4cb71c18fe045a763ff6681a8ebbbbbec0b2b
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:11 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:32 -0700

x86, olpc: Add XO-1 suspend/resume support

Add code needed for basic suspend/resume of the XO-1 laptop.
Based on earlier work by Jordan Crouse, Andres Salomon, and others.

This patch incorporates all earlier feedback from Thomas Gleixner. To
clarify a certain point (now more obvious in the code itself):
On resume, OpenFirmware returns execution to Linux in protected mode
with a kernel-compatible GDT already set up. The changes and
simplifications suggested have all been included.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-5-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                     |    4 +-
 arch/x86/include/asm/olpc.h          |   15 +++-
 arch/x86/platform/olpc/Makefile      |    2 +-
 arch/x86/platform/olpc/olpc-xo1-pm.c |   92 +++++++++++++++++++++++++
 arch/x86/platform/olpc/xo1-wakeup.S  |  124 ++++++++++++++++++++++++++++++++++
 include/linux/cs5535.h               |    3 +
 6 files changed, 234 insertions(+), 6 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 29615ee..f473151 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2075,10 +2075,10 @@ config OLPC
 
 config OLPC_XO1_PM
 	bool "OLPC XO-1 Power Management"
-	depends on OLPC && MFD_CS5535
+	depends on OLPC && MFD_CS5535 && PM_SLEEP
 	select MFD_CORE
 	---help---
-	  Add support for poweroff of the OLPC XO-1 laptop.
+	  Add support for poweroff and suspend of the OLPC XO-1 laptop.
 
 endif # X86_32
 
diff --git a/arch/x86/include/asm/olpc.h b/arch/x86/include/asm/olpc.h
index 5ca6801..10ea595 100644
--- a/arch/x86/include/asm/olpc.h
+++ b/arch/x86/include/asm/olpc.h
@@ -76,6 +76,12 @@ static inline int olpc_has_dcon(void)
 
 #endif
 
+#ifdef CONFIG_OLPC_XO1_PM
+extern void do_olpc_suspend_lowlevel(void);
+extern void olpc_xo1_pm_wakeup_set(u16 value);
+extern void olpc_xo1_pm_wakeup_clear(u16 value);
+#endif
+
 extern int pci_olpc_init(void);
 
 /* EC related functions */
@@ -88,9 +94,12 @@ extern int olpc_ec_mask_unset(uint8_t bits);
 
 /* EC commands */
 
-#define EC_FIRMWARE_REV		0x08
-#define EC_WLAN_ENTER_RESET	0x35
-#define EC_WLAN_LEAVE_RESET	0x25
+#define EC_FIRMWARE_REV			0x08
+#define EC_WAKE_UP_WLAN			0x24
+#define EC_WLAN_LEAVE_RESET		0x25
+#define EC_SET_SCI_INHIBIT		0x32
+#define EC_SET_SCI_INHIBIT_RELEASE	0x34
+#define EC_WLAN_ENTER_RESET		0x35
 
 /* SCI source values */
 
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index cd25038..1ae7bed 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,2 +1,2 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
-obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o
+obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-pm.c b/arch/x86/platform/olpc/olpc-xo1-pm.c
index a2a59d3..6f3855a 100644
--- a/arch/x86/platform/olpc/olpc-xo1-pm.c
+++ b/arch/x86/platform/olpc/olpc-xo1-pm.c
@@ -16,6 +16,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
+#include <linux/suspend.h>
 
 #include <asm/io.h>
 #include <asm/olpc.h>
@@ -25,6 +26,85 @@
 static unsigned long acpi_base;
 static unsigned long pms_base;
 
+static u16 wakeup_mask = CS5536_PM_PWRBTN;
+
+static struct {
+	unsigned long address;
+	unsigned short segment;
+} ofw_bios_entry = { 0xF0000 + PAGE_OFFSET, __KERNEL_CS };
+
+/* Set bits in the wakeup mask */
+void olpc_xo1_pm_wakeup_set(u16 value)
+{
+	wakeup_mask |= value;
+}
+EXPORT_SYMBOL_GPL(olpc_xo1_pm_wakeup_set);
+
+/* Clear bits in the wakeup mask */
+void olpc_xo1_pm_wakeup_clear(u16 value)
+{
+	wakeup_mask &= ~value;
+}
+EXPORT_SYMBOL_GPL(olpc_xo1_pm_wakeup_clear);
+
+static int xo1_power_state_enter(suspend_state_t pm_state)
+{
+	unsigned long saved_sci_mask;
+	int r;
+
+	/* Only STR is supported */
+	if (pm_state != PM_SUSPEND_MEM)
+		return -EINVAL;
+
+	r = olpc_ec_cmd(EC_SET_SCI_INHIBIT, NULL, 0, NULL, 0);
+	if (r)
+		return r;
+
+	/*
+	 * Save SCI mask (this gets lost since PM1_EN is used as a mask for
+	 * wakeup events, which is not necessarily the same event set)
+	 */
+	saved_sci_mask = inl(acpi_base + CS5536_PM1_STS);
+	saved_sci_mask &= 0xffff0000;
+
+	/* Save CPU state */
+	do_olpc_suspend_lowlevel();
+
+	/* Resume path starts here */
+
+	/* Restore SCI mask (using dword access to CS5536_PM1_EN) */
+	outl(saved_sci_mask, acpi_base + CS5536_PM1_STS);
+
+	/* Tell the EC to stop inhibiting SCIs */
+	olpc_ec_cmd(EC_SET_SCI_INHIBIT_RELEASE, NULL, 0, NULL, 0);
+
+	/*
+	 * Tell the wireless module to restart USB communication.
+	 * Must be done twice.
+	 */
+	olpc_ec_cmd(EC_WAKE_UP_WLAN, NULL, 0, NULL, 0);
+	olpc_ec_cmd(EC_WAKE_UP_WLAN, NULL, 0, NULL, 0);
+
+	return 0;
+}
+
+asmlinkage int xo1_do_sleep(u8 sleep_state)
+{
+	void *pgd_addr = __va(read_cr3());
+
+	/* Program wakeup mask (using dword access to CS5536_PM1_EN) */
+	outl(wakeup_mask << 16, acpi_base + CS5536_PM1_STS);
+
+	__asm__("movl %0,%%eax" : : "r" (pgd_addr));
+	__asm__("call *(%%edi); cld"
+		: : "D" (&ofw_bios_entry));
+	__asm__("movb $0x34, %al\n\t"
+		"outb %al, $0x70\n\t"
+		"movb $0x30, %al\n\t"
+		"outb %al, $0x71\n\t");
+	return 0;
+}
+
 static void xo1_power_off(void)
 {
 	printk(KERN_INFO "OLPC XO-1 power off sequence...\n");
@@ -43,6 +123,17 @@ static void xo1_power_off(void)
 	outl(0x00002000, acpi_base + CS5536_PM1_CNT);
 }
 
+static int xo1_power_state_valid(suspend_state_t pm_state)
+{
+	/* suspend-to-RAM only */
+	return pm_state == PM_SUSPEND_MEM;
+}
+
+static const struct platform_suspend_ops xo1_suspend_ops = {
+	.valid = xo1_power_state_valid,
+	.enter = xo1_power_state_enter,
+};
+
 static int __devinit xo1_pm_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -68,6 +159,7 @@ static int __devinit xo1_pm_probe(struct platform_device *pdev)
 
 	/* If we have both addresses, we can override the poweroff hook */
 	if (pms_base && acpi_base) {
+		suspend_set_ops(&xo1_suspend_ops);
 		pm_power_off = xo1_power_off;
 		printk(KERN_INFO "OLPC XO-1 support registered\n");
 	}
diff --git a/arch/x86/platform/olpc/xo1-wakeup.S b/arch/x86/platform/olpc/xo1-wakeup.S
new file mode 100644
index 0000000..948deb2
--- /dev/null
+++ b/arch/x86/platform/olpc/xo1-wakeup.S
@@ -0,0 +1,124 @@
+.text
+#include <linux/linkage.h>
+#include <asm/segment.h>
+#include <asm/page.h>
+#include <asm/pgtable_32.h>
+
+	.macro writepost,value
+		movb $0x34, %al
+		outb %al, $0x70
+		movb $\value, %al
+		outb %al, $0x71
+	.endm
+
+wakeup_start:
+	# OFW lands us here, running in protected mode, with a
+	# kernel-compatible GDT already setup.
+
+	# Clear any dangerous flags
+	pushl $0
+	popfl
+
+	writepost 0x31
+
+	# Set up %cr3
+	movl $initial_page_table - __PAGE_OFFSET, %eax
+	movl %eax, %cr3
+
+	movl saved_cr4, %eax
+	movl %eax, %cr4
+
+	movl saved_cr0, %eax
+	movl %eax, %cr0
+
+	# Control registers were modified, pipeline resync is needed
+	jmp 1f
+1:
+
+	movw    $__KERNEL_DS, %ax
+	movw    %ax, %ss
+	movw    %ax, %ds
+	movw    %ax, %es
+	movw    %ax, %fs
+	movw    %ax, %gs
+
+	lgdt    saved_gdt
+	lidt    saved_idt
+	lldt    saved_ldt
+	ljmp    $(__KERNEL_CS),$1f
+1:
+	movl    %cr3, %eax
+	movl    %eax, %cr3
+	wbinvd
+
+	# Go back to the return point
+	jmp ret_point
+
+save_registers:
+	sgdt  saved_gdt
+	sidt  saved_idt
+	sldt  saved_ldt
+
+	pushl %edx
+	movl %cr4, %edx
+	movl %edx, saved_cr4
+
+	movl %cr0, %edx
+	movl %edx, saved_cr0
+
+	popl %edx
+
+	movl %ebx, saved_context_ebx
+	movl %ebp, saved_context_ebp
+	movl %esi, saved_context_esi
+	movl %edi, saved_context_edi
+
+	pushfl
+	popl saved_context_eflags
+
+	ret
+
+restore_registers:
+	movl saved_context_ebp, %ebp
+	movl saved_context_ebx, %ebx
+	movl saved_context_esi, %esi
+	movl saved_context_edi, %edi
+
+	pushl saved_context_eflags
+	popfl
+
+	ret
+
+ENTRY(do_olpc_suspend_lowlevel)
+	call	save_processor_state
+	call	save_registers
+
+	# This is the stack context we want to remember
+	movl %esp, saved_context_esp
+
+	pushl	$3
+	call	xo1_do_sleep
+
+	jmp	wakeup_start
+	.p2align 4,,7
+ret_point:
+	movl    saved_context_esp, %esp
+
+	writepost 0x32
+
+	call	restore_registers
+	call	restore_processor_state
+	ret
+
+.data
+saved_gdt:             .long   0,0
+saved_idt:             .long   0,0
+saved_ldt:             .long   0
+saved_cr4:             .long   0
+saved_cr0:             .long   0
+saved_context_esp:     .long   0
+saved_context_edi:     .long   0
+saved_context_esi:     .long   0
+saved_context_ebx:     .long   0
+saved_context_ebp:     .long   0
+saved_context_eflags:  .long   0
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index e46b8b0..2facf16 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -70,6 +70,9 @@
 #define CS5536_PM1_CNT		0x08
 #define CS5536_PM_GPE0_STS	0x18
 
+/* CS5536_PM1_EN bits */
+#define CS5536_PM_PWRBTN	(1 << 8)
+
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
 #define VSA_VRC_DATA		0xAC1E

[PATCH v3 05/11] x86, olpc: Add XO-1 SCI driver and power button control

[Daniel Drake]

The System Control Interrupt is used in the OLPC XO-1 to control various
features of the laptop. Add the driver base and the power button
functionality.

This driver can't be built as a module, because functionality added in
future patches means that some drivers need to know at boot-time whether
SCI-based functionality is available.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                      |    9 ++
 arch/x86/platform/olpc/Makefile       |    1 +
 arch/x86/platform/olpc/olpc-xo1-sci.c |  191 +++++++++++++++++++++++++++++++++
 include/linux/cs5535.h                |    8 ++
 4 files changed, 209 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/platform/olpc/olpc-xo1-sci.c

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index a9953bf..b2fb1e4 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2082,6 +2082,15 @@ config OLPC_XO1_PM
 	---help---
 	  Add support for poweroff and suspend of the OLPC XO-1 laptop.
 
+config OLPC_XO1_SCI
+	bool "OLPC XO-1 SCI extras"
+	depends on OLPC && OLPC_XO1_PM
+	select GPIO_CS5535
+	select MFD_CORE
+	---help---
+	  Add support for SCI-based features of the OLPC XO-1 laptop:
+	   - Power button
+
 endif # X86_32
 
 config AMD_NB
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 1ae7bed..1ec5ade 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,2 +1,3 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
 obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
+obj-$(CONFIG_OLPC_XO1_SCI)	+= olpc-xo1-sci.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
new file mode 100644
index 0000000..8fbf961
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -0,0 +1,191 @@
+/*
+ * Support for OLPC XO-1 System Control Interrupts (SCI)
+ *
+ * Copyright (C) 2010 One Laptop per Child
+ * Copyright (C) 2006 Red Hat, Inc.
+ * Copyright (C) 2006 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/cs5535.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/mfd/core.h>
+#include <linux/suspend.h>
+
+#include <asm/io.h>
+#include <asm/msr.h>
+#include <asm/olpc.h>
+
+#define DRV_NAME	"olpc-xo1-sci"
+#define PFX		DRV_NAME ": "
+
+static unsigned long acpi_base;
+static struct input_dev *power_button_idev;
+static int sci_irq;
+
+static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
+{
+	struct platform_device *pdev = dev_id;
+	u32 sts;
+	u32 gpe;
+
+	sts = inl(acpi_base + CS5536_PM1_STS);
+	outl(sts | 0xffff, acpi_base + CS5536_PM1_STS);
+
+	gpe = inl(acpi_base + CS5536_PM_GPE0_STS);
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
+
+	dev_dbg(&pdev->dev, "sts %x gpe %x\n", sts, gpe);
+
+	if (sts & CS5536_PWRBTN_FLAG && !(sts & CS5536_WAK_FLAG)) {
+		input_report_key(power_button_idev, KEY_POWER, 1);
+		input_sync(power_button_idev);
+		input_report_key(power_button_idev, KEY_POWER, 0);
+		input_sync(power_button_idev);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int xo1_sci_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	if (device_may_wakeup(&power_button_idev->dev))
+		olpc_xo1_pm_wakeup_set(CS5536_PM_PWRBTN);
+	else
+		olpc_xo1_pm_wakeup_clear(CS5536_PM_PWRBTN);
+	return 0;
+}
+
+static int __devinit setup_sci_interrupt(struct platform_device *pdev)
+{
+	u32 lo, hi;
+	u32 sts;
+	int r;
+
+	rdmsr(0x51400020, lo, hi);
+	sci_irq = (lo >> 20) & 15;
+
+	if (sci_irq) {
+		dev_info(&pdev->dev, "SCI is mapped to IRQ %d\n", sci_irq);
+	} else {
+		/* Zero means masked */
+		dev_info(&pdev->dev, "SCI unmapped. Mapping to IRQ 3\n");
+		sci_irq = 3;
+		lo |= 0x00300000;
+		wrmsrl(0x51400020, lo);
+	}
+
+	/* Select level triggered in PIC */
+	if (sci_irq < 8) {
+		lo = inb(CS5536_PIC_INT_SEL1);
+		lo |= 1 << sci_irq;
+		outb(lo, CS5536_PIC_INT_SEL1);
+	} else {
+		lo = inb(CS5536_PIC_INT_SEL2);
+		lo |= 1 << (sci_irq - 8);
+		outb(lo, CS5536_PIC_INT_SEL2);
+	}
+
+	/* Enable SCI from power button, and clear pending interrupts */
+	sts = inl(acpi_base + CS5536_PM1_STS);
+	outl((CS5536_PM_PWRBTN << 16) | 0xffff, acpi_base + CS5536_PM1_STS);
+
+	r = request_irq(sci_irq, xo1_sci_intr, 0, DRV_NAME, pdev);
+	if (r)
+		dev_err(&pdev->dev, "can't request interrupt\n");
+
+	return r;
+}
+
+static int __devinit setup_power_button(struct platform_device *pdev)
+{
+	int r;
+
+	power_button_idev = input_allocate_device();
+	if (!power_button_idev)
+		return -ENOMEM;
+
+	power_button_idev->name = "Power Button";
+	power_button_idev->phys = DRV_NAME "/input0";
+	set_bit(EV_KEY, power_button_idev->evbit);
+	set_bit(KEY_POWER, power_button_idev->keybit);
+
+	power_button_idev->dev.parent = &pdev->dev;
+	device_init_wakeup(&power_button_idev->dev, 1);
+
+	r = input_register_device(power_button_idev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to register power button: %d\n", r);
+		input_free_device(power_button_idev);
+	}
+
+	return r;
+}
+
+static void free_power_button(void)
+{
+	input_unregister_device(power_button_idev);
+	input_free_device(power_button_idev);
+}
+
+static int __devinit xo1_sci_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	int r;
+
+	/* don't run on non-XOs */
+	if (!machine_is_olpc())
+		return -ENODEV;
+
+	r = mfd_cell_enable(pdev);
+	if (r)
+		return r;
+
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "can't fetch device resource info\n");
+		return -EIO;
+	}
+	acpi_base = res->start;
+
+	r = setup_power_button(pdev);
+	if (r)
+		return r;
+
+	r = setup_sci_interrupt(pdev);
+	if (r)
+		free_power_button();
+
+	return r;
+}
+
+static int __devexit xo1_sci_remove(struct platform_device *pdev)
+{
+	mfd_cell_disable(pdev);
+	free_irq(sci_irq, pdev);
+	free_power_button();
+	acpi_base = 0;
+	return 0;
+}
+
+static struct platform_driver xo1_sci_driver = {
+	.driver = {
+		.name = "olpc-xo1-sci-acpi",
+	},
+	.probe = xo1_sci_probe,
+	.remove = __devexit_p(xo1_sci_remove),
+	.suspend = xo1_sci_suspend,
+};
+
+static int __init xo1_sci_init(void)
+{
+	return platform_driver_register(&xo1_sci_driver);
+}
+arch_initcall(xo1_sci_init);
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 2facf16..6f78235 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -43,6 +43,10 @@
 #define MSR_GX_GLD_MSR_CONFIG	0xC0002001
 #define MSR_GX_MSR_PADSEL	0xC0002011
 
+/* PIC registers */
+#define CS5536_PIC_INT_SEL1	0x4d0
+#define CS5536_PIC_INT_SEL2	0x4d1
+
 /* resource sizes */
 #define LBAR_GPIO_SIZE		0xFF
 #define LBAR_MFGPT_SIZE		0x40
@@ -70,6 +74,10 @@
 #define CS5536_PM1_CNT		0x08
 #define CS5536_PM_GPE0_STS	0x18
 
+/* CS5536_PM1_STS bits */
+#define CS5536_WAK_FLAG		(1 << 15)
+#define CS5536_PWRBTN_FLAG	(1 << 8)
+
 /* CS5536_PM1_EN bits */
 #define CS5536_PM_PWRBTN	(1 << 8)
 
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Add XO-1 SCI driver and power button control

[tip-bot for Daniel Drake]

Commit-ID:  7feda8e9f35ebb0e9f90e03acb02280bc137f784
Gitweb:     http://git.kernel.org/tip/7feda8e9f35ebb0e9f90e03acb02280bc137f784
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:12 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:34 -0700

x86, olpc: Add XO-1 SCI driver and power button control

The System Control Interrupt is used in the OLPC XO-1 to control various
features of the laptop. Add the driver base and the power button
functionality.

This driver can't be built as a module, because functionality added in
future patches means that some drivers need to know at boot-time whether
SCI-based functionality is available.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-6-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                      |    9 ++
 arch/x86/platform/olpc/Makefile       |    1 +
 arch/x86/platform/olpc/olpc-xo1-sci.c |  191 +++++++++++++++++++++++++++++++++
 include/linux/cs5535.h                |    8 ++
 4 files changed, 209 insertions(+), 0 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index f473151..66b7b9d 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2080,6 +2080,15 @@ config OLPC_XO1_PM
 	---help---
 	  Add support for poweroff and suspend of the OLPC XO-1 laptop.
 
+config OLPC_XO1_SCI
+	bool "OLPC XO-1 SCI extras"
+	depends on OLPC && OLPC_XO1_PM
+	select GPIO_CS5535
+	select MFD_CORE
+	---help---
+	  Add support for SCI-based features of the OLPC XO-1 laptop:
+	   - Power button
+
 endif # X86_32
 
 config AMD_NB
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 1ae7bed..1ec5ade 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,2 +1,3 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
 obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
+obj-$(CONFIG_OLPC_XO1_SCI)	+= olpc-xo1-sci.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
new file mode 100644
index 0000000..8fbf961
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -0,0 +1,191 @@
+/*
+ * Support for OLPC XO-1 System Control Interrupts (SCI)
+ *
+ * Copyright (C) 2010 One Laptop per Child
+ * Copyright (C) 2006 Red Hat, Inc.
+ * Copyright (C) 2006 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/cs5535.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/mfd/core.h>
+#include <linux/suspend.h>
+
+#include <asm/io.h>
+#include <asm/msr.h>
+#include <asm/olpc.h>
+
+#define DRV_NAME	"olpc-xo1-sci"
+#define PFX		DRV_NAME ": "
+
+static unsigned long acpi_base;
+static struct input_dev *power_button_idev;
+static int sci_irq;
+
+static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
+{
+	struct platform_device *pdev = dev_id;
+	u32 sts;
+	u32 gpe;
+
+	sts = inl(acpi_base + CS5536_PM1_STS);
+	outl(sts | 0xffff, acpi_base + CS5536_PM1_STS);
+
+	gpe = inl(acpi_base + CS5536_PM_GPE0_STS);
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
+
+	dev_dbg(&pdev->dev, "sts %x gpe %x\n", sts, gpe);
+
+	if (sts & CS5536_PWRBTN_FLAG && !(sts & CS5536_WAK_FLAG)) {
+		input_report_key(power_button_idev, KEY_POWER, 1);
+		input_sync(power_button_idev);
+		input_report_key(power_button_idev, KEY_POWER, 0);
+		input_sync(power_button_idev);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int xo1_sci_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	if (device_may_wakeup(&power_button_idev->dev))
+		olpc_xo1_pm_wakeup_set(CS5536_PM_PWRBTN);
+	else
+		olpc_xo1_pm_wakeup_clear(CS5536_PM_PWRBTN);
+	return 0;
+}
+
+static int __devinit setup_sci_interrupt(struct platform_device *pdev)
+{
+	u32 lo, hi;
+	u32 sts;
+	int r;
+
+	rdmsr(0x51400020, lo, hi);
+	sci_irq = (lo >> 20) & 15;
+
+	if (sci_irq) {
+		dev_info(&pdev->dev, "SCI is mapped to IRQ %d\n", sci_irq);
+	} else {
+		/* Zero means masked */
+		dev_info(&pdev->dev, "SCI unmapped. Mapping to IRQ 3\n");
+		sci_irq = 3;
+		lo |= 0x00300000;
+		wrmsrl(0x51400020, lo);
+	}
+
+	/* Select level triggered in PIC */
+	if (sci_irq < 8) {
+		lo = inb(CS5536_PIC_INT_SEL1);
+		lo |= 1 << sci_irq;
+		outb(lo, CS5536_PIC_INT_SEL1);
+	} else {
+		lo = inb(CS5536_PIC_INT_SEL2);
+		lo |= 1 << (sci_irq - 8);
+		outb(lo, CS5536_PIC_INT_SEL2);
+	}
+
+	/* Enable SCI from power button, and clear pending interrupts */
+	sts = inl(acpi_base + CS5536_PM1_STS);
+	outl((CS5536_PM_PWRBTN << 16) | 0xffff, acpi_base + CS5536_PM1_STS);
+
+	r = request_irq(sci_irq, xo1_sci_intr, 0, DRV_NAME, pdev);
+	if (r)
+		dev_err(&pdev->dev, "can't request interrupt\n");
+
+	return r;
+}
+
+static int __devinit setup_power_button(struct platform_device *pdev)
+{
+	int r;
+
+	power_button_idev = input_allocate_device();
+	if (!power_button_idev)
+		return -ENOMEM;
+
+	power_button_idev->name = "Power Button";
+	power_button_idev->phys = DRV_NAME "/input0";
+	set_bit(EV_KEY, power_button_idev->evbit);
+	set_bit(KEY_POWER, power_button_idev->keybit);
+
+	power_button_idev->dev.parent = &pdev->dev;
+	device_init_wakeup(&power_button_idev->dev, 1);
+
+	r = input_register_device(power_button_idev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to register power button: %d\n", r);
+		input_free_device(power_button_idev);
+	}
+
+	return r;
+}
+
+static void free_power_button(void)
+{
+	input_unregister_device(power_button_idev);
+	input_free_device(power_button_idev);
+}
+
+static int __devinit xo1_sci_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	int r;
+
+	/* don't run on non-XOs */
+	if (!machine_is_olpc())
+		return -ENODEV;
+
+	r = mfd_cell_enable(pdev);
+	if (r)
+		return r;
+
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "can't fetch device resource info\n");
+		return -EIO;
+	}
+	acpi_base = res->start;
+
+	r = setup_power_button(pdev);
+	if (r)
+		return r;
+
+	r = setup_sci_interrupt(pdev);
+	if (r)
+		free_power_button();
+
+	return r;
+}
+
+static int __devexit xo1_sci_remove(struct platform_device *pdev)
+{
+	mfd_cell_disable(pdev);
+	free_irq(sci_irq, pdev);
+	free_power_button();
+	acpi_base = 0;
+	return 0;
+}
+
+static struct platform_driver xo1_sci_driver = {
+	.driver = {
+		.name = "olpc-xo1-sci-acpi",
+	},
+	.probe = xo1_sci_probe,
+	.remove = __devexit_p(xo1_sci_remove),
+	.suspend = xo1_sci_suspend,
+};
+
+static int __init xo1_sci_init(void)
+{
+	return platform_driver_register(&xo1_sci_driver);
+}
+arch_initcall(xo1_sci_init);
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 2facf16..6f78235 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -43,6 +43,10 @@
 #define MSR_GX_GLD_MSR_CONFIG	0xC0002001
 #define MSR_GX_MSR_PADSEL	0xC0002011
 
+/* PIC registers */
+#define CS5536_PIC_INT_SEL1	0x4d0
+#define CS5536_PIC_INT_SEL2	0x4d1
+
 /* resource sizes */
 #define LBAR_GPIO_SIZE		0xFF
 #define LBAR_MFGPT_SIZE		0x40
@@ -70,6 +74,10 @@
 #define CS5536_PM1_CNT		0x08
 #define CS5536_PM_GPE0_STS	0x18
 
+/* CS5536_PM1_STS bits */
+#define CS5536_WAK_FLAG		(1 << 15)
+#define CS5536_PWRBTN_FLAG	(1 << 8)
+
 /* CS5536_PM1_EN bits */
 #define CS5536_PM_PWRBTN	(1 << 8)
 

[PATCH v3 06/11] x86, olpc: EC SCI wakeup mask functionality

[Daniel Drake]

Update the EC SCI masks with recent additions.

Add functions to query SCI events and set the wakeup mask, to be used by
followup patches.

Add functions to tweak an event mask used to select certain EC events as
a system wakeup source. Also add a function to determine if EC wakeup
functionality is available, as this depends on child drivers (different
for each laptop model) to configure the SCI interrupt.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/include/asm/olpc.h   |   31 ++++++++++++---
 arch/x86/platform/olpc/olpc.c |   86 +++++++++++++++++++++++++++++++++++++++++
 2 files changed, 111 insertions(+), 6 deletions(-)

diff --git a/arch/x86/include/asm/olpc.h b/arch/x86/include/asm/olpc.h
index 10ea595..0e56d01 100644
--- a/arch/x86/include/asm/olpc.h
+++ b/arch/x86/include/asm/olpc.h
@@ -13,6 +13,7 @@ struct olpc_platform_t {
 
 #define OLPC_F_PRESENT		0x01
 #define OLPC_F_DCON		0x02
+#define OLPC_F_EC_WIDE_SCI	0x04
 
 #ifdef CONFIG_OLPC
 
@@ -62,6 +63,13 @@ static inline int olpc_board_at_least(uint32_t rev)
 	return olpc_platform_info.boardrev >= rev;
 }
 
+extern void olpc_ec_wakeup_set(u16 value);
+extern void olpc_ec_wakeup_clear(u16 value);
+extern bool olpc_ec_wakeup_available(void);
+
+extern int olpc_ec_mask_write(u16 bits);
+extern int olpc_ec_sci_query(u16 *sci_value);
+
 #else
 
 static inline int machine_is_olpc(void)
@@ -74,6 +82,14 @@ static inline int olpc_has_dcon(void)
 	return 0;
 }
 
+static inline void olpc_ec_wakeup_set(u16 value) { }
+static inline void olpc_ec_wakeup_clear(u16 value) { }
+
+static inline bool olpc_ec_wakeup_available(void)
+{
+	return false;
+}
+
 #endif
 
 #ifdef CONFIG_OLPC_XO1_PM
@@ -89,17 +105,18 @@ extern int pci_olpc_init(void);
 extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
 		unsigned char *outbuf, size_t outlen);
 
-extern int olpc_ec_mask_set(uint8_t bits);
-extern int olpc_ec_mask_unset(uint8_t bits);
-
 /* EC commands */
 
 #define EC_FIRMWARE_REV			0x08
+#define EC_WRITE_SCI_MASK		0x1b
 #define EC_WAKE_UP_WLAN			0x24
 #define EC_WLAN_LEAVE_RESET		0x25
 #define EC_SET_SCI_INHIBIT		0x32
 #define EC_SET_SCI_INHIBIT_RELEASE	0x34
 #define EC_WLAN_ENTER_RESET		0x35
+#define EC_WRITE_EXT_SCI_MASK		0x38
+#define EC_SCI_QUERY			0x84
+#define EC_EXT_SCI_QUERY		0x85
 
 /* SCI source values */
 
@@ -108,10 +125,12 @@ extern int olpc_ec_mask_unset(uint8_t bits);
 #define EC_SCI_SRC_BATTERY	0x02
 #define EC_SCI_SRC_BATSOC	0x04
 #define EC_SCI_SRC_BATERR	0x08
-#define EC_SCI_SRC_EBOOK	0x10
-#define EC_SCI_SRC_WLAN		0x20
+#define EC_SCI_SRC_EBOOK	0x10	/* XO-1 only */
+#define EC_SCI_SRC_WLAN		0x20	/* XO-1 only */
 #define EC_SCI_SRC_ACPWR	0x40
-#define EC_SCI_SRC_ALL		0x7F
+#define EC_SCI_SRC_BATCRIT	0x80
+#define EC_SCI_SRC_GPWAKE	0x100	/* XO-1.5 only */
+#define EC_SCI_SRC_ALL		0x1FF
 
 /* GPIO assignments */
 
diff --git a/arch/x86/platform/olpc/olpc.c b/arch/x86/platform/olpc/olpc.c
index 0060fd5..72fd041 100644
--- a/arch/x86/platform/olpc/olpc.c
+++ b/arch/x86/platform/olpc/olpc.c
@@ -19,6 +19,7 @@
 #include <linux/string.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
+#include <linux/syscore_ops.h>
 
 #include <asm/geode.h>
 #include <asm/setup.h>
@@ -30,6 +31,9 @@ EXPORT_SYMBOL_GPL(olpc_platform_info);
 
 static DEFINE_SPINLOCK(ec_lock);
 
+/* EC event mask to be applied during suspend (defining wakeup sources). */
+static u16 ec_wakeup_mask;
+
 /* what the timeout *should* be (in ms) */
 #define EC_BASE_TIMEOUT 20
 
@@ -188,6 +192,79 @@ err:
 }
 EXPORT_SYMBOL_GPL(olpc_ec_cmd);
 
+void olpc_ec_wakeup_set(u16 value)
+{
+	ec_wakeup_mask |= value;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_wakeup_set);
+
+void olpc_ec_wakeup_clear(u16 value)
+{
+	ec_wakeup_mask &= ~value;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_wakeup_clear);
+
+/*
+ * Returns true if the compile and runtime configurations allow for EC events
+ * to wake the system.
+ */
+bool olpc_ec_wakeup_available(void)
+{
+	if (!machine_is_olpc())
+		return false;
+
+	/*
+	 * XO-1 EC wakeups are available when olpc-xo1-sci driver is
+	 * compiled in
+	 */
+#ifdef CONFIG_OLPC_XO1_SCI
+	if (olpc_platform_info.boardrev < olpc_board_pre(0xd0)) /* XO-1 */
+		return true;
+#endif
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_wakeup_available);
+
+int olpc_ec_mask_write(u16 bits)
+{
+	if (olpc_platform_info.flags & OLPC_F_EC_WIDE_SCI) {
+		__be16 ec_word = cpu_to_be16(bits);
+		return olpc_ec_cmd(EC_WRITE_EXT_SCI_MASK, (void *) &ec_word, 2,
+				   NULL, 0);
+	} else {
+		unsigned char ec_byte = bits & 0xff;
+		return olpc_ec_cmd(EC_WRITE_SCI_MASK, &ec_byte, 1, NULL, 0);
+	}
+}
+EXPORT_SYMBOL_GPL(olpc_ec_mask_write);
+
+int olpc_ec_sci_query(u16 *sci_value)
+{
+	int ret;
+
+	if (olpc_platform_info.flags & OLPC_F_EC_WIDE_SCI) {
+		__be16 ec_word;
+		ret = olpc_ec_cmd(EC_EXT_SCI_QUERY,
+			NULL, 0, (void *) &ec_word, 2);
+		if (ret == 0)
+			*sci_value = be16_to_cpu(ec_word);
+	} else {
+		unsigned char ec_byte;
+		ret = olpc_ec_cmd(EC_SCI_QUERY, NULL, 0, &ec_byte, 1);
+		if (ret == 0)
+			*sci_value = ec_byte;
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_sci_query);
+
+static int olpc_ec_suspend(void)
+{
+	return olpc_ec_mask_write(ec_wakeup_mask);
+}
+
 static bool __init check_ofw_architecture(struct device_node *root)
 {
 	const char *olpc_arch;
@@ -242,6 +319,10 @@ static int __init add_xo1_platform_devices(void)
 	return 0;
 }
 
+static struct syscore_ops olpc_syscore_ops = {
+	.suspend = olpc_ec_suspend,
+};
+
 static int __init olpc_init(void)
 {
 	int r = 0;
@@ -266,6 +347,9 @@ static int __init olpc_init(void)
 			!cs5535_has_vsa2())
 		x86_init.pci.arch_init = pci_olpc_init;
 #endif
+	/* EC version 0x5f adds support for wide SCI mask */
+	if (olpc_platform_info.ecver >= 0x5f)
+		olpc_platform_info.flags |= OLPC_F_EC_WIDE_SCI;
 
 	printk(KERN_INFO "OLPC board revision %s%X (EC=%x)\n",
 			((olpc_platform_info.boardrev & 0xf) < 8) ? "pre" : "",
@@ -278,6 +362,8 @@ static int __init olpc_init(void)
 			return r;
 	}
 
+	register_syscore_ops(&olpc_syscore_ops);
+
 	return 0;
 }
 
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: EC SCI wakeup mask functionality

[tip-bot for Daniel Drake]

Commit-ID:  bc4ecd5a5efc2435e6debfb7b279a15ae96697fd
Gitweb:     http://git.kernel.org/tip/bc4ecd5a5efc2435e6debfb7b279a15ae96697fd
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:13 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:36 -0700

x86, olpc: EC SCI wakeup mask functionality

Update the EC SCI masks with recent additions.

Add functions to query SCI events and set the wakeup mask, to be used by
followup patches.

Add functions to tweak an event mask used to select certain EC events as
a system wakeup source. Also add a function to determine if EC wakeup
functionality is available, as this depends on child drivers (different
for each laptop model) to configure the SCI interrupt.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-7-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/include/asm/olpc.h   |   31 ++++++++++++---
 arch/x86/platform/olpc/olpc.c |   86 +++++++++++++++++++++++++++++++++++++++++
 2 files changed, 111 insertions(+), 6 deletions(-)

diff --git a/arch/x86/include/asm/olpc.h b/arch/x86/include/asm/olpc.h
index 10ea595..0e56d01 100644
--- a/arch/x86/include/asm/olpc.h
+++ b/arch/x86/include/asm/olpc.h
@@ -13,6 +13,7 @@ struct olpc_platform_t {
 
 #define OLPC_F_PRESENT		0x01
 #define OLPC_F_DCON		0x02
+#define OLPC_F_EC_WIDE_SCI	0x04
 
 #ifdef CONFIG_OLPC
 
@@ -62,6 +63,13 @@ static inline int olpc_board_at_least(uint32_t rev)
 	return olpc_platform_info.boardrev >= rev;
 }
 
+extern void olpc_ec_wakeup_set(u16 value);
+extern void olpc_ec_wakeup_clear(u16 value);
+extern bool olpc_ec_wakeup_available(void);
+
+extern int olpc_ec_mask_write(u16 bits);
+extern int olpc_ec_sci_query(u16 *sci_value);
+
 #else
 
 static inline int machine_is_olpc(void)
@@ -74,6 +82,14 @@ static inline int olpc_has_dcon(void)
 	return 0;
 }
 
+static inline void olpc_ec_wakeup_set(u16 value) { }
+static inline void olpc_ec_wakeup_clear(u16 value) { }
+
+static inline bool olpc_ec_wakeup_available(void)
+{
+	return false;
+}
+
 #endif
 
 #ifdef CONFIG_OLPC_XO1_PM
@@ -89,17 +105,18 @@ extern int pci_olpc_init(void);
 extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
 		unsigned char *outbuf, size_t outlen);
 
-extern int olpc_ec_mask_set(uint8_t bits);
-extern int olpc_ec_mask_unset(uint8_t bits);
-
 /* EC commands */
 
 #define EC_FIRMWARE_REV			0x08
+#define EC_WRITE_SCI_MASK		0x1b
 #define EC_WAKE_UP_WLAN			0x24
 #define EC_WLAN_LEAVE_RESET		0x25
 #define EC_SET_SCI_INHIBIT		0x32
 #define EC_SET_SCI_INHIBIT_RELEASE	0x34
 #define EC_WLAN_ENTER_RESET		0x35
+#define EC_WRITE_EXT_SCI_MASK		0x38
+#define EC_SCI_QUERY			0x84
+#define EC_EXT_SCI_QUERY		0x85
 
 /* SCI source values */
 
@@ -108,10 +125,12 @@ extern int olpc_ec_mask_unset(uint8_t bits);
 #define EC_SCI_SRC_BATTERY	0x02
 #define EC_SCI_SRC_BATSOC	0x04
 #define EC_SCI_SRC_BATERR	0x08
-#define EC_SCI_SRC_EBOOK	0x10
-#define EC_SCI_SRC_WLAN		0x20
+#define EC_SCI_SRC_EBOOK	0x10	/* XO-1 only */
+#define EC_SCI_SRC_WLAN		0x20	/* XO-1 only */
 #define EC_SCI_SRC_ACPWR	0x40
-#define EC_SCI_SRC_ALL		0x7F
+#define EC_SCI_SRC_BATCRIT	0x80
+#define EC_SCI_SRC_GPWAKE	0x100	/* XO-1.5 only */
+#define EC_SCI_SRC_ALL		0x1FF
 
 /* GPIO assignments */
 
diff --git a/arch/x86/platform/olpc/olpc.c b/arch/x86/platform/olpc/olpc.c
index 0060fd5..72fd041 100644
--- a/arch/x86/platform/olpc/olpc.c
+++ b/arch/x86/platform/olpc/olpc.c
@@ -19,6 +19,7 @@
 #include <linux/string.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
+#include <linux/syscore_ops.h>
 
 #include <asm/geode.h>
 #include <asm/setup.h>
@@ -30,6 +31,9 @@ EXPORT_SYMBOL_GPL(olpc_platform_info);
 
 static DEFINE_SPINLOCK(ec_lock);
 
+/* EC event mask to be applied during suspend (defining wakeup sources). */
+static u16 ec_wakeup_mask;
+
 /* what the timeout *should* be (in ms) */
 #define EC_BASE_TIMEOUT 20
 
@@ -188,6 +192,79 @@ err:
 }
 EXPORT_SYMBOL_GPL(olpc_ec_cmd);
 
+void olpc_ec_wakeup_set(u16 value)
+{
+	ec_wakeup_mask |= value;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_wakeup_set);
+
+void olpc_ec_wakeup_clear(u16 value)
+{
+	ec_wakeup_mask &= ~value;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_wakeup_clear);
+
+/*
+ * Returns true if the compile and runtime configurations allow for EC events
+ * to wake the system.
+ */
+bool olpc_ec_wakeup_available(void)
+{
+	if (!machine_is_olpc())
+		return false;
+
+	/*
+	 * XO-1 EC wakeups are available when olpc-xo1-sci driver is
+	 * compiled in
+	 */
+#ifdef CONFIG_OLPC_XO1_SCI
+	if (olpc_platform_info.boardrev < olpc_board_pre(0xd0)) /* XO-1 */
+		return true;
+#endif
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_wakeup_available);
+
+int olpc_ec_mask_write(u16 bits)
+{
+	if (olpc_platform_info.flags & OLPC_F_EC_WIDE_SCI) {
+		__be16 ec_word = cpu_to_be16(bits);
+		return olpc_ec_cmd(EC_WRITE_EXT_SCI_MASK, (void *) &ec_word, 2,
+				   NULL, 0);
+	} else {
+		unsigned char ec_byte = bits & 0xff;
+		return olpc_ec_cmd(EC_WRITE_SCI_MASK, &ec_byte, 1, NULL, 0);
+	}
+}
+EXPORT_SYMBOL_GPL(olpc_ec_mask_write);
+
+int olpc_ec_sci_query(u16 *sci_value)
+{
+	int ret;
+
+	if (olpc_platform_info.flags & OLPC_F_EC_WIDE_SCI) {
+		__be16 ec_word;
+		ret = olpc_ec_cmd(EC_EXT_SCI_QUERY,
+			NULL, 0, (void *) &ec_word, 2);
+		if (ret == 0)
+			*sci_value = be16_to_cpu(ec_word);
+	} else {
+		unsigned char ec_byte;
+		ret = olpc_ec_cmd(EC_SCI_QUERY, NULL, 0, &ec_byte, 1);
+		if (ret == 0)
+			*sci_value = ec_byte;
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(olpc_ec_sci_query);
+
+static int olpc_ec_suspend(void)
+{
+	return olpc_ec_mask_write(ec_wakeup_mask);
+}
+
 static bool __init check_ofw_architecture(struct device_node *root)
 {
 	const char *olpc_arch;
@@ -242,6 +319,10 @@ static int __init add_xo1_platform_devices(void)
 	return 0;
 }
 
+static struct syscore_ops olpc_syscore_ops = {
+	.suspend = olpc_ec_suspend,
+};
+
 static int __init olpc_init(void)
 {
 	int r = 0;
@@ -266,6 +347,9 @@ static int __init olpc_init(void)
 			!cs5535_has_vsa2())
 		x86_init.pci.arch_init = pci_olpc_init;
 #endif
+	/* EC version 0x5f adds support for wide SCI mask */
+	if (olpc_platform_info.ecver >= 0x5f)
+		olpc_platform_info.flags |= OLPC_F_EC_WIDE_SCI;
 
 	printk(KERN_INFO "OLPC board revision %s%X (EC=%x)\n",
 			((olpc_platform_info.boardrev & 0xf) < 8) ? "pre" : "",
@@ -278,6 +362,8 @@ static int __init olpc_init(void)
 			return r;
 	}
 
+	register_syscore_ops(&olpc_syscore_ops);
+
 	return 0;
 }
 

[PATCH v3 07/11] x86, olpc-xo1-sci: Add GPE handler and ebook switch functionality

[Daniel Drake]

The EC in the OLPC XO-1 delivers GPE events to provide various
notifications. Add the basic code for GPE/EC event processing and
enable the ebook switch, which can be used as a wakeup source.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                      |    2 +
 arch/x86/include/asm/olpc.h           |    5 +-
 arch/x86/platform/olpc/olpc-xo1-sci.c |  183 ++++++++++++++++++++++++++++++++-
 include/linux/cs5535.h                |   22 ++++
 4 files changed, 209 insertions(+), 3 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index b2fb1e4..f527dfd 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2089,7 +2089,9 @@ config OLPC_XO1_SCI
 	select MFD_CORE
 	---help---
 	  Add support for SCI-based features of the OLPC XO-1 laptop:
+	   - EC-driven system wakeups
 	   - Power button
+	   - Ebook switch
 
 endif # X86_32
 
diff --git a/arch/x86/include/asm/olpc.h b/arch/x86/include/asm/olpc.h
index 0e56d01..87bdbca 100644
--- a/arch/x86/include/asm/olpc.h
+++ b/arch/x86/include/asm/olpc.h
@@ -111,6 +111,7 @@ extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
 #define EC_WRITE_SCI_MASK		0x1b
 #define EC_WAKE_UP_WLAN			0x24
 #define EC_WLAN_LEAVE_RESET		0x25
+#define EC_READ_EB_MODE			0x2a
 #define EC_SET_SCI_INHIBIT		0x32
 #define EC_SET_SCI_INHIBIT_RELEASE	0x34
 #define EC_WLAN_ENTER_RESET		0x35
@@ -144,7 +145,7 @@ extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
 #define OLPC_GPIO_SMB_CLK      14
 #define OLPC_GPIO_SMB_DATA     15
 #define OLPC_GPIO_WORKAUX	geode_gpio(24)
-#define OLPC_GPIO_LID		geode_gpio(26)
-#define OLPC_GPIO_ECSCI		geode_gpio(27)
+#define OLPC_GPIO_LID		26
+#define OLPC_GPIO_ECSCI		27
 
 #endif /* _ASM_X86_OLPC_H */
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
index 8fbf961..63f5050 100644
--- a/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -12,12 +12,15 @@
  */
 
 #include <linux/cs5535.h>
+#include <linux/device.h>
+#include <linux/gpio.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
 #include <linux/suspend.h>
+#include <linux/workqueue.h>
 
 #include <asm/io.h>
 #include <asm/msr.h>
@@ -28,8 +31,60 @@
 
 static unsigned long acpi_base;
 static struct input_dev *power_button_idev;
+static struct input_dev *ebook_switch_idev;
+
 static int sci_irq;
 
+/* Report current ebook switch state through input layer */
+static void send_ebook_state(void)
+{
+	unsigned char state;
+
+	if (olpc_ec_cmd(EC_READ_EB_MODE, NULL, 0, &state, 1)) {
+		pr_err(PFX "failed to get ebook state\n");
+		return;
+	}
+
+	input_report_switch(ebook_switch_idev, SW_TABLET_MODE, state);
+	input_sync(ebook_switch_idev);
+}
+
+/*
+ * Process all items in the EC's SCI queue.
+ *
+ * This is handled in a workqueue because olpc_ec_cmd can be slow (and
+ * can even timeout).
+ *
+ * If propagate_events is false, the queue is drained without events being
+ * generated for the interrupts.
+ */
+static void process_sci_queue(bool propagate_events)
+{
+	int r;
+	u16 data;
+
+	do {
+		r = olpc_ec_sci_query(&data);
+		if (r || !data)
+			break;
+
+		pr_debug(PFX "SCI 0x%x received\n", data);
+
+		if (data == EC_SCI_SRC_EBOOK && propagate_events)
+			send_ebook_state();
+	} while (data);
+
+	if (r)
+		pr_err(PFX "Failed to clear SCI queue");
+}
+
+static void process_sci_queue_work(struct work_struct *work)
+{
+	process_sci_queue(true);
+}
+
+static DECLARE_WORK(sci_work, process_sci_queue_work);
+
 static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
 {
 	struct platform_device *pdev = dev_id;
@@ -51,6 +106,11 @@ static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
 		input_sync(power_button_idev);
 	}
 
+	if (gpe & CS5536_GPIOM7_PME_FLAG) { /* EC GPIO */
+		cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_NEGATIVE_EDGE_STS);
+		schedule_work(&sci_work);
+	}
+
 	return IRQ_HANDLED;
 }
 
@@ -60,6 +120,19 @@ static int xo1_sci_suspend(struct platform_device *pdev, pm_message_t state)
 		olpc_xo1_pm_wakeup_set(CS5536_PM_PWRBTN);
 	else
 		olpc_xo1_pm_wakeup_clear(CS5536_PM_PWRBTN);
+
+	if (device_may_wakeup(&ebook_switch_idev->dev))
+		olpc_ec_wakeup_set(EC_SCI_SRC_EBOOK);
+	else
+		olpc_ec_wakeup_clear(EC_SCI_SRC_EBOOK);
+
+	return 0;
+}
+
+static int xo1_sci_resume(struct platform_device *pdev)
+{
+	/* Enable all EC events */
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
 	return 0;
 }
 
@@ -104,6 +177,50 @@ static int __devinit setup_sci_interrupt(struct platform_device *pdev)
 	return r;
 }
 
+static int __devinit setup_ec_sci(void)
+{
+	int r;
+
+	r = gpio_request(OLPC_GPIO_ECSCI, "OLPC-ECSCI");
+	if (r)
+		return r;
+
+	gpio_direction_input(OLPC_GPIO_ECSCI);
+
+	/* Clear pending EC SCI events */
+	cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_NEGATIVE_EDGE_STS);
+	cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_POSITIVE_EDGE_STS);
+
+	/*
+	 * Enable EC SCI events, and map them to both a PME and the SCI
+	 * interrupt.
+	 *
+	 * Ordinarily, in addition to functioning as GPIOs, Geode GPIOs can
+	 * be mapped to regular interrupts *or* Geode-specific Power
+	 * Management Events (PMEs) - events that bring the system out of
+	 * suspend. In this case, we want both of those things - the system
+	 * wakeup, *and* the ability to get an interrupt when an event occurs.
+	 *
+	 * To achieve this, we map the GPIO to a PME, and then we use one
+	 * of the many generic knobs on the CS5535 PIC to additionally map the
+	 * PME to the regular SCI interrupt line.
+	 */
+	cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_EVENTS_ENABLE);
+
+	/* Set the SCI to cause a PME event on group 7 */
+	cs5535_gpio_setup_event(OLPC_GPIO_ECSCI, 7, 1);
+
+	/* And have group 7 also fire the SCI interrupt */
+	cs5535_pic_unreqz_select_high(7, sci_irq);
+
+	return 0;
+}
+
+static void free_ec_sci(void)
+{
+	gpio_free(OLPC_GPIO_ECSCI);
+}
+
 static int __devinit setup_power_button(struct platform_device *pdev)
 {
 	int r;
@@ -135,6 +252,37 @@ static void free_power_button(void)
 	input_free_device(power_button_idev);
 }
 
+static int __devinit setup_ebook_switch(struct platform_device *pdev)
+{
+	int r;
+
+	ebook_switch_idev = input_allocate_device();
+	if (!ebook_switch_idev)
+		return -ENOMEM;
+
+	ebook_switch_idev->name = "EBook Switch";
+	ebook_switch_idev->phys = DRV_NAME "/input1";
+	set_bit(EV_SW, ebook_switch_idev->evbit);
+	set_bit(SW_TABLET_MODE, ebook_switch_idev->swbit);
+
+	ebook_switch_idev->dev.parent = &pdev->dev;
+	device_set_wakeup_capable(&ebook_switch_idev->dev, true);
+
+	r = input_register_device(ebook_switch_idev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to register ebook switch: %d\n", r);
+		input_free_device(ebook_switch_idev);
+	}
+
+	return r;
+}
+
+static void free_ebook_switch(void)
+{
+	input_unregister_device(ebook_switch_idev);
+	input_free_device(ebook_switch_idev);
+}
+
 static int __devinit xo1_sci_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -159,10 +307,39 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 	if (r)
 		return r;
 
+	r = setup_ebook_switch(pdev);
+	if (r)
+		goto err_ebook;
+
+	r = setup_ec_sci();
+	if (r)
+		goto err_ecsci;
+
+	/* Enable PME generation for EC-generated events */
+	outl(CS5536_GPIOM7_PME_EN, acpi_base + CS5536_PM_GPE0_EN);
+
+	/* Clear pending events */
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
+	process_sci_queue(false);
+
+	/* Initial sync */
+	send_ebook_state();
+
 	r = setup_sci_interrupt(pdev);
 	if (r)
-		free_power_button();
+		goto err_sci;
 
+	/* Enable all EC events */
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	return r;
+
+err_sci:
+	free_ec_sci();
+err_ecsci:
+	free_ebook_switch();
+err_ebook:
+	free_power_button();
 	return r;
 }
 
@@ -170,6 +347,9 @@ static int __devexit xo1_sci_remove(struct platform_device *pdev)
 {
 	mfd_cell_disable(pdev);
 	free_irq(sci_irq, pdev);
+	cancel_work_sync(&sci_work);
+	free_ec_sci();
+	free_ebook_switch();
 	free_power_button();
 	acpi_base = 0;
 	return 0;
@@ -182,6 +362,7 @@ static struct platform_driver xo1_sci_driver = {
 	.probe = xo1_sci_probe,
 	.remove = __devexit_p(xo1_sci_remove),
 	.suspend = xo1_sci_suspend,
+	.resume = xo1_sci_resume,
 };
 
 static int __init xo1_sci_init(void)
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 6f78235..d7e9a7f 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -11,6 +11,8 @@
 #ifndef _CS5535_H
 #define _CS5535_H
 
+#include <asm/msr.h>
+
 /* MSRs */
 #define MSR_GLIU_P2D_RO0	0x10000029
 
@@ -43,6 +45,18 @@
 #define MSR_GX_GLD_MSR_CONFIG	0xC0002001
 #define MSR_GX_MSR_PADSEL	0xC0002011
 
+static inline int cs5535_pic_unreqz_select_high(unsigned int group,
+						unsigned int irq)
+{
+	uint32_t lo, hi;
+
+	rdmsr(MSR_PIC_ZSEL_HIGH, lo, hi);
+	lo &= ~(0xF << (group * 4));
+	lo |= (irq & 0xF) << (group * 4);
+	wrmsr(MSR_PIC_ZSEL_HIGH, lo, hi);
+	return 0;
+}
+
 /* PIC registers */
 #define CS5536_PIC_INT_SEL1	0x4d0
 #define CS5536_PIC_INT_SEL2	0x4d1
@@ -73,6 +87,7 @@
 #define CS5536_PM1_EN		0x02
 #define CS5536_PM1_CNT		0x08
 #define CS5536_PM_GPE0_STS	0x18
+#define CS5536_PM_GPE0_EN	0x1c
 
 /* CS5536_PM1_STS bits */
 #define CS5536_WAK_FLAG		(1 << 15)
@@ -81,6 +96,13 @@
 /* CS5536_PM1_EN bits */
 #define CS5536_PM_PWRBTN	(1 << 8)
 
+/* CS5536_PM_GPE0_STS bits */
+#define CS5536_GPIOM7_PME_FLAG	(1 << 31)
+#define CS5536_GPIOM6_PME_FLAG	(1 << 30)
+
+/* CS5536_PM_GPE0_EN bits */
+#define CS5536_GPIOM7_PME_EN	(1 << 31)
+
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
 #define VSA_VRC_DATA		0xAC1E
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc-xo1-sci: Add GPE handler and ebook switch functionality

[tip-bot for Daniel Drake]

Commit-ID:  7bc74b3df73776fe06f3df9fafd2d2698e6ca28a
Gitweb:     http://git.kernel.org/tip/7bc74b3df73776fe06f3df9fafd2d2698e6ca28a
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:14 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:38 -0700

x86, olpc-xo1-sci: Add GPE handler and ebook switch functionality

The EC in the OLPC XO-1 delivers GPE events to provide various
notifications. Add the basic code for GPE/EC event processing and
enable the ebook switch, which can be used as a wakeup source.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-8-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                      |    2 +
 arch/x86/include/asm/olpc.h           |    5 +-
 arch/x86/platform/olpc/olpc-xo1-sci.c |  183 ++++++++++++++++++++++++++++++++-
 include/linux/cs5535.h                |   22 ++++
 4 files changed, 209 insertions(+), 3 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 66b7b9d..8888910 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2087,7 +2087,9 @@ config OLPC_XO1_SCI
 	select MFD_CORE
 	---help---
 	  Add support for SCI-based features of the OLPC XO-1 laptop:
+	   - EC-driven system wakeups
 	   - Power button
+	   - Ebook switch
 
 endif # X86_32
 
diff --git a/arch/x86/include/asm/olpc.h b/arch/x86/include/asm/olpc.h
index 0e56d01..87bdbca 100644
--- a/arch/x86/include/asm/olpc.h
+++ b/arch/x86/include/asm/olpc.h
@@ -111,6 +111,7 @@ extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
 #define EC_WRITE_SCI_MASK		0x1b
 #define EC_WAKE_UP_WLAN			0x24
 #define EC_WLAN_LEAVE_RESET		0x25
+#define EC_READ_EB_MODE			0x2a
 #define EC_SET_SCI_INHIBIT		0x32
 #define EC_SET_SCI_INHIBIT_RELEASE	0x34
 #define EC_WLAN_ENTER_RESET		0x35
@@ -144,7 +145,7 @@ extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
 #define OLPC_GPIO_SMB_CLK      14
 #define OLPC_GPIO_SMB_DATA     15
 #define OLPC_GPIO_WORKAUX	geode_gpio(24)
-#define OLPC_GPIO_LID		geode_gpio(26)
-#define OLPC_GPIO_ECSCI		geode_gpio(27)
+#define OLPC_GPIO_LID		26
+#define OLPC_GPIO_ECSCI		27
 
 #endif /* _ASM_X86_OLPC_H */
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
index 8fbf961..63f5050 100644
--- a/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -12,12 +12,15 @@
  */
 
 #include <linux/cs5535.h>
+#include <linux/device.h>
+#include <linux/gpio.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
 #include <linux/suspend.h>
+#include <linux/workqueue.h>
 
 #include <asm/io.h>
 #include <asm/msr.h>
@@ -28,8 +31,60 @@
 
 static unsigned long acpi_base;
 static struct input_dev *power_button_idev;
+static struct input_dev *ebook_switch_idev;
+
 static int sci_irq;
 
+/* Report current ebook switch state through input layer */
+static void send_ebook_state(void)
+{
+	unsigned char state;
+
+	if (olpc_ec_cmd(EC_READ_EB_MODE, NULL, 0, &state, 1)) {
+		pr_err(PFX "failed to get ebook state\n");
+		return;
+	}
+
+	input_report_switch(ebook_switch_idev, SW_TABLET_MODE, state);
+	input_sync(ebook_switch_idev);
+}
+
+/*
+ * Process all items in the EC's SCI queue.
+ *
+ * This is handled in a workqueue because olpc_ec_cmd can be slow (and
+ * can even timeout).
+ *
+ * If propagate_events is false, the queue is drained without events being
+ * generated for the interrupts.
+ */
+static void process_sci_queue(bool propagate_events)
+{
+	int r;
+	u16 data;
+
+	do {
+		r = olpc_ec_sci_query(&data);
+		if (r || !data)
+			break;
+
+		pr_debug(PFX "SCI 0x%x received\n", data);
+
+		if (data == EC_SCI_SRC_EBOOK && propagate_events)
+			send_ebook_state();
+	} while (data);
+
+	if (r)
+		pr_err(PFX "Failed to clear SCI queue");
+}
+
+static void process_sci_queue_work(struct work_struct *work)
+{
+	process_sci_queue(true);
+}
+
+static DECLARE_WORK(sci_work, process_sci_queue_work);
+
 static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
 {
 	struct platform_device *pdev = dev_id;
@@ -51,6 +106,11 @@ static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
 		input_sync(power_button_idev);
 	}
 
+	if (gpe & CS5536_GPIOM7_PME_FLAG) { /* EC GPIO */
+		cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_NEGATIVE_EDGE_STS);
+		schedule_work(&sci_work);
+	}
+
 	return IRQ_HANDLED;
 }
 
@@ -60,6 +120,19 @@ static int xo1_sci_suspend(struct platform_device *pdev, pm_message_t state)
 		olpc_xo1_pm_wakeup_set(CS5536_PM_PWRBTN);
 	else
 		olpc_xo1_pm_wakeup_clear(CS5536_PM_PWRBTN);
+
+	if (device_may_wakeup(&ebook_switch_idev->dev))
+		olpc_ec_wakeup_set(EC_SCI_SRC_EBOOK);
+	else
+		olpc_ec_wakeup_clear(EC_SCI_SRC_EBOOK);
+
+	return 0;
+}
+
+static int xo1_sci_resume(struct platform_device *pdev)
+{
+	/* Enable all EC events */
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
 	return 0;
 }
 
@@ -104,6 +177,50 @@ static int __devinit setup_sci_interrupt(struct platform_device *pdev)
 	return r;
 }
 
+static int __devinit setup_ec_sci(void)
+{
+	int r;
+
+	r = gpio_request(OLPC_GPIO_ECSCI, "OLPC-ECSCI");
+	if (r)
+		return r;
+
+	gpio_direction_input(OLPC_GPIO_ECSCI);
+
+	/* Clear pending EC SCI events */
+	cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_NEGATIVE_EDGE_STS);
+	cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_POSITIVE_EDGE_STS);
+
+	/*
+	 * Enable EC SCI events, and map them to both a PME and the SCI
+	 * interrupt.
+	 *
+	 * Ordinarily, in addition to functioning as GPIOs, Geode GPIOs can
+	 * be mapped to regular interrupts *or* Geode-specific Power
+	 * Management Events (PMEs) - events that bring the system out of
+	 * suspend. In this case, we want both of those things - the system
+	 * wakeup, *and* the ability to get an interrupt when an event occurs.
+	 *
+	 * To achieve this, we map the GPIO to a PME, and then we use one
+	 * of the many generic knobs on the CS5535 PIC to additionally map the
+	 * PME to the regular SCI interrupt line.
+	 */
+	cs5535_gpio_set(OLPC_GPIO_ECSCI, GPIO_EVENTS_ENABLE);
+
+	/* Set the SCI to cause a PME event on group 7 */
+	cs5535_gpio_setup_event(OLPC_GPIO_ECSCI, 7, 1);
+
+	/* And have group 7 also fire the SCI interrupt */
+	cs5535_pic_unreqz_select_high(7, sci_irq);
+
+	return 0;
+}
+
+static void free_ec_sci(void)
+{
+	gpio_free(OLPC_GPIO_ECSCI);
+}
+
 static int __devinit setup_power_button(struct platform_device *pdev)
 {
 	int r;
@@ -135,6 +252,37 @@ static void free_power_button(void)
 	input_free_device(power_button_idev);
 }
 
+static int __devinit setup_ebook_switch(struct platform_device *pdev)
+{
+	int r;
+
+	ebook_switch_idev = input_allocate_device();
+	if (!ebook_switch_idev)
+		return -ENOMEM;
+
+	ebook_switch_idev->name = "EBook Switch";
+	ebook_switch_idev->phys = DRV_NAME "/input1";
+	set_bit(EV_SW, ebook_switch_idev->evbit);
+	set_bit(SW_TABLET_MODE, ebook_switch_idev->swbit);
+
+	ebook_switch_idev->dev.parent = &pdev->dev;
+	device_set_wakeup_capable(&ebook_switch_idev->dev, true);
+
+	r = input_register_device(ebook_switch_idev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to register ebook switch: %d\n", r);
+		input_free_device(ebook_switch_idev);
+	}
+
+	return r;
+}
+
+static void free_ebook_switch(void)
+{
+	input_unregister_device(ebook_switch_idev);
+	input_free_device(ebook_switch_idev);
+}
+
 static int __devinit xo1_sci_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -159,10 +307,39 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 	if (r)
 		return r;
 
+	r = setup_ebook_switch(pdev);
+	if (r)
+		goto err_ebook;
+
+	r = setup_ec_sci();
+	if (r)
+		goto err_ecsci;
+
+	/* Enable PME generation for EC-generated events */
+	outl(CS5536_GPIOM7_PME_EN, acpi_base + CS5536_PM_GPE0_EN);
+
+	/* Clear pending events */
+	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
+	process_sci_queue(false);
+
+	/* Initial sync */
+	send_ebook_state();
+
 	r = setup_sci_interrupt(pdev);
 	if (r)
-		free_power_button();
+		goto err_sci;
 
+	/* Enable all EC events */
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	return r;
+
+err_sci:
+	free_ec_sci();
+err_ecsci:
+	free_ebook_switch();
+err_ebook:
+	free_power_button();
 	return r;
 }
 
@@ -170,6 +347,9 @@ static int __devexit xo1_sci_remove(struct platform_device *pdev)
 {
 	mfd_cell_disable(pdev);
 	free_irq(sci_irq, pdev);
+	cancel_work_sync(&sci_work);
+	free_ec_sci();
+	free_ebook_switch();
 	free_power_button();
 	acpi_base = 0;
 	return 0;
@@ -182,6 +362,7 @@ static struct platform_driver xo1_sci_driver = {
 	.probe = xo1_sci_probe,
 	.remove = __devexit_p(xo1_sci_remove),
 	.suspend = xo1_sci_suspend,
+	.resume = xo1_sci_resume,
 };
 
 static int __init xo1_sci_init(void)
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 6f78235..d7e9a7f 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -11,6 +11,8 @@
 #ifndef _CS5535_H
 #define _CS5535_H
 
+#include <asm/msr.h>
+
 /* MSRs */
 #define MSR_GLIU_P2D_RO0	0x10000029
 
@@ -43,6 +45,18 @@
 #define MSR_GX_GLD_MSR_CONFIG	0xC0002001
 #define MSR_GX_MSR_PADSEL	0xC0002011
 
+static inline int cs5535_pic_unreqz_select_high(unsigned int group,
+						unsigned int irq)
+{
+	uint32_t lo, hi;
+
+	rdmsr(MSR_PIC_ZSEL_HIGH, lo, hi);
+	lo &= ~(0xF << (group * 4));
+	lo |= (irq & 0xF) << (group * 4);
+	wrmsr(MSR_PIC_ZSEL_HIGH, lo, hi);
+	return 0;
+}
+
 /* PIC registers */
 #define CS5536_PIC_INT_SEL1	0x4d0
 #define CS5536_PIC_INT_SEL2	0x4d1
@@ -73,6 +87,7 @@
 #define CS5536_PM1_EN		0x02
 #define CS5536_PM1_CNT		0x08
 #define CS5536_PM_GPE0_STS	0x18
+#define CS5536_PM_GPE0_EN	0x1c
 
 /* CS5536_PM1_STS bits */
 #define CS5536_WAK_FLAG		(1 << 15)
@@ -81,6 +96,13 @@
 /* CS5536_PM1_EN bits */
 #define CS5536_PM_PWRBTN	(1 << 8)
 
+/* CS5536_PM_GPE0_STS bits */
+#define CS5536_GPIOM7_PME_FLAG	(1 << 31)
+#define CS5536_GPIOM6_PME_FLAG	(1 << 30)
+
+/* CS5536_PM_GPE0_EN bits */
+#define CS5536_GPIOM7_PME_EN	(1 << 31)
+
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
 #define VSA_VRC_DATA		0xAC1E

[PATCH v3 08/11] x86, olpc-xo1-sci: Add lid switch functionality

[Daniel Drake]

Configure the XO-1's lid switch GPIO to trigger an SCI interrupt,
and correctly expose this input device which can be used as a wakeup
source.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                      |    1 +
 arch/x86/platform/olpc/olpc-xo1-sci.c |  207 ++++++++++++++++++++++++++++++++-
 include/linux/cs5535.h                |    1 +
 3 files changed, 208 insertions(+), 1 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index f527dfd..f5bc969 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2092,6 +2092,7 @@ config OLPC_XO1_SCI
 	   - EC-driven system wakeups
 	   - Power button
 	   - Ebook switch
+	   - Lid switch
 
 endif # X86_32
 
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
index 63f5050..ad0670b 100644
--- a/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -32,9 +32,26 @@
 static unsigned long acpi_base;
 static struct input_dev *power_button_idev;
 static struct input_dev *ebook_switch_idev;
+static struct input_dev *lid_switch_idev;
 
 static int sci_irq;
 
+static bool lid_open;
+static bool lid_inverted;
+static int lid_wake_mode;
+
+enum lid_wake_modes {
+	LID_WAKE_ALWAYS,
+	LID_WAKE_OPEN,
+	LID_WAKE_CLOSE,
+};
+
+static const char * const lid_wake_mode_names[] = {
+	[LID_WAKE_ALWAYS] = "always",
+	[LID_WAKE_OPEN] = "open",
+	[LID_WAKE_CLOSE] = "close",
+};
+
 /* Report current ebook switch state through input layer */
 static void send_ebook_state(void)
 {
@@ -49,6 +66,70 @@ static void send_ebook_state(void)
 	input_sync(ebook_switch_idev);
 }
 
+static void flip_lid_inverter(void)
+{
+	/* gpio is high; invert so we'll get l->h event interrupt */
+	if (lid_inverted)
+		cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_INPUT_INVERT);
+	else
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_INPUT_INVERT);
+	lid_inverted = !lid_inverted;
+}
+
+static void detect_lid_state(void)
+{
+	/*
+	 * the edge detector hookup on the gpio inputs on the geode is
+	 * odd, to say the least.  See http://dev.laptop.org/ticket/5703
+	 * for details, but in a nutshell:  we don't use the edge
+	 * detectors.  instead, we make use of an anomoly:  with the both
+	 * edge detectors turned off, we still get an edge event on a
+	 * positive edge transition.  to take advantage of this, we use the
+	 * front-end inverter to ensure that that's the edge we're always
+	 * going to see next.
+	 */
+
+	int state;
+
+	state = cs5535_gpio_isset(OLPC_GPIO_LID, GPIO_READ_BACK);
+	lid_open = !state ^ !lid_inverted; /* x ^^ y */
+	if (!state)
+		return;
+
+	flip_lid_inverter();
+}
+
+/* Report current lid switch state through input layer */
+static void send_lid_state(void)
+{
+	input_report_switch(lid_switch_idev, SW_LID, !lid_open);
+	input_sync(lid_switch_idev);
+}
+
+static ssize_t lid_wake_mode_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	const char *mode = lid_wake_mode_names[lid_wake_mode];
+	return sprintf(buf, "%s\n", mode);
+}
+static ssize_t lid_wake_mode_set(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	int i;
+	for (i = 0; i < ARRAY_SIZE(lid_wake_mode_names); i++) {
+		const char *mode = lid_wake_mode_names[i];
+		if (strlen(mode) != count || strncasecmp(mode, buf, count))
+			continue;
+
+		lid_wake_mode = i;
+		return count;
+	}
+	return -EINVAL;
+}
+static DEVICE_ATTR(lid_wake_mode, S_IWUSR | S_IRUGO, lid_wake_mode_show,
+		   lid_wake_mode_set);
+
 /*
  * Process all items in the EC's SCI queue.
  *
@@ -111,6 +192,11 @@ static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
 		schedule_work(&sci_work);
 	}
 
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_STS);
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_STS);
+	detect_lid_state();
+	send_lid_state();
+
 	return IRQ_HANDLED;
 }
 
@@ -126,11 +212,32 @@ static int xo1_sci_suspend(struct platform_device *pdev, pm_message_t state)
 	else
 		olpc_ec_wakeup_clear(EC_SCI_SRC_EBOOK);
 
+	if (!device_may_wakeup(&lid_switch_idev->dev)) {
+		cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+	} else if ((lid_open && lid_wake_mode == LID_WAKE_OPEN) ||
+		   (!lid_open && lid_wake_mode == LID_WAKE_CLOSE)) {
+		flip_lid_inverter();
+
+		/* we may have just caused an event */
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_STS);
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_STS);
+
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+	}
+
 	return 0;
 }
 
 static int xo1_sci_resume(struct platform_device *pdev)
 {
+	/*
+	 * We don't know what may have happened while we were asleep.
+	 * Reestablish our lid setup so we're sure to catch all transitions.
+	 */
+	detect_lid_state();
+	send_lid_state();
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+
 	/* Enable all EC events */
 	olpc_ec_mask_write(EC_SCI_SRC_ALL);
 	return 0;
@@ -221,6 +328,43 @@ static void free_ec_sci(void)
 	gpio_free(OLPC_GPIO_ECSCI);
 }
 
+static int __devinit setup_lid_events(void)
+{
+	int r;
+
+	r = gpio_request(OLPC_GPIO_LID, "OLPC-LID");
+	if (r)
+		return r;
+
+	gpio_direction_input(OLPC_GPIO_LID);
+
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_INPUT_INVERT);
+	lid_inverted = 0;
+
+	/* Clear edge detection and event enable for now */
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_EN);
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_EN);
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_STS);
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_STS);
+
+	/* Set the LID to cause an PME event on group 6 */
+	cs5535_gpio_setup_event(OLPC_GPIO_LID, 6, 1);
+
+	/* Set PME group 6 to fire the SCI interrupt */
+	cs5535_gpio_set_irq(6, sci_irq);
+
+	/* Enable the event */
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+
+	return 0;
+}
+
+static void free_lid_events(void)
+{
+	gpio_free(OLPC_GPIO_LID);
+}
+
 static int __devinit setup_power_button(struct platform_device *pdev)
 {
 	int r;
@@ -283,6 +427,50 @@ static void free_ebook_switch(void)
 	input_free_device(ebook_switch_idev);
 }
 
+static int __devinit setup_lid_switch(struct platform_device *pdev)
+{
+	int r;
+
+	lid_switch_idev = input_allocate_device();
+	if (!lid_switch_idev)
+		return -ENOMEM;
+
+	lid_switch_idev->name = "Lid Switch";
+	lid_switch_idev->phys = DRV_NAME "/input2";
+	set_bit(EV_SW, lid_switch_idev->evbit);
+	set_bit(SW_LID, lid_switch_idev->swbit);
+
+	lid_switch_idev->dev.parent = &pdev->dev;
+	device_set_wakeup_capable(&lid_switch_idev->dev, true);
+
+	r = input_register_device(lid_switch_idev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to register lid switch: %d\n", r);
+		goto err_register;
+	}
+
+	r = device_create_file(&lid_switch_idev->dev, &dev_attr_lid_wake_mode);
+	if (r) {
+		dev_err(&pdev->dev, "failed to create wake mode attr: %d\n", r);
+		goto err_create_attr;
+	}
+
+	return 0;
+
+err_create_attr:
+	input_unregister_device(lid_switch_idev);
+err_register:
+	input_free_device(lid_switch_idev);
+	return r;
+}
+
+static void free_lid_switch(void)
+{
+	device_remove_file(&lid_switch_idev->dev, &dev_attr_lid_wake_mode);
+	input_unregister_device(lid_switch_idev);
+	input_free_device(lid_switch_idev);
+}
+
 static int __devinit xo1_sci_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -311,12 +499,21 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 	if (r)
 		goto err_ebook;
 
+	r = setup_lid_switch(pdev);
+	if (r)
+		goto err_lid;
+
+	r = setup_lid_events();
+	if (r)
+		goto err_lidevt;
+
 	r = setup_ec_sci();
 	if (r)
 		goto err_ecsci;
 
 	/* Enable PME generation for EC-generated events */
-	outl(CS5536_GPIOM7_PME_EN, acpi_base + CS5536_PM_GPE0_EN);
+	outl(CS5536_GPIOM6_PME_EN | CS5536_GPIOM7_PME_EN,
+		acpi_base + CS5536_PM_GPE0_EN);
 
 	/* Clear pending events */
 	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
@@ -324,6 +521,8 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 
 	/* Initial sync */
 	send_ebook_state();
+	detect_lid_state();
+	send_lid_state();
 
 	r = setup_sci_interrupt(pdev);
 	if (r)
@@ -337,6 +536,10 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 err_sci:
 	free_ec_sci();
 err_ecsci:
+	free_lid_events();
+err_lidevt:
+	free_lid_switch();
+err_lid:
 	free_ebook_switch();
 err_ebook:
 	free_power_button();
@@ -349,6 +552,8 @@ static int __devexit xo1_sci_remove(struct platform_device *pdev)
 	free_irq(sci_irq, pdev);
 	cancel_work_sync(&sci_work);
 	free_ec_sci();
+	free_lid_events();
+	free_lid_switch();
 	free_ebook_switch();
 	free_power_button();
 	acpi_base = 0;
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index d7e9a7f..72954c6 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -102,6 +102,7 @@ static inline int cs5535_pic_unreqz_select_high(unsigned int group,
 
 /* CS5536_PM_GPE0_EN bits */
 #define CS5536_GPIOM7_PME_EN	(1 << 31)
+#define CS5536_GPIOM6_PME_EN	(1 << 30)
 
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc-xo1-sci: Add lid switch functionality

[tip-bot for Daniel Drake]

Commit-ID:  2cf2baea103f0a3d68b0f989d28df66f16dbc834
Gitweb:     http://git.kernel.org/tip/2cf2baea103f0a3d68b0f989d28df66f16dbc834
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:15 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:39 -0700

x86, olpc-xo1-sci: Add lid switch functionality

Configure the XO-1's lid switch GPIO to trigger an SCI interrupt,
and correctly expose this input device which can be used as a wakeup
source.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-9-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                      |    1 +
 arch/x86/platform/olpc/olpc-xo1-sci.c |  207 ++++++++++++++++++++++++++++++++-
 include/linux/cs5535.h                |    1 +
 3 files changed, 208 insertions(+), 1 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 8888910..350ccbb 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2090,6 +2090,7 @@ config OLPC_XO1_SCI
 	   - EC-driven system wakeups
 	   - Power button
 	   - Ebook switch
+	   - Lid switch
 
 endif # X86_32
 
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
index 63f5050..ad0670b 100644
--- a/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -32,9 +32,26 @@
 static unsigned long acpi_base;
 static struct input_dev *power_button_idev;
 static struct input_dev *ebook_switch_idev;
+static struct input_dev *lid_switch_idev;
 
 static int sci_irq;
 
+static bool lid_open;
+static bool lid_inverted;
+static int lid_wake_mode;
+
+enum lid_wake_modes {
+	LID_WAKE_ALWAYS,
+	LID_WAKE_OPEN,
+	LID_WAKE_CLOSE,
+};
+
+static const char * const lid_wake_mode_names[] = {
+	[LID_WAKE_ALWAYS] = "always",
+	[LID_WAKE_OPEN] = "open",
+	[LID_WAKE_CLOSE] = "close",
+};
+
 /* Report current ebook switch state through input layer */
 static void send_ebook_state(void)
 {
@@ -49,6 +66,70 @@ static void send_ebook_state(void)
 	input_sync(ebook_switch_idev);
 }
 
+static void flip_lid_inverter(void)
+{
+	/* gpio is high; invert so we'll get l->h event interrupt */
+	if (lid_inverted)
+		cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_INPUT_INVERT);
+	else
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_INPUT_INVERT);
+	lid_inverted = !lid_inverted;
+}
+
+static void detect_lid_state(void)
+{
+	/*
+	 * the edge detector hookup on the gpio inputs on the geode is
+	 * odd, to say the least.  See http://dev.laptop.org/ticket/5703
+	 * for details, but in a nutshell:  we don't use the edge
+	 * detectors.  instead, we make use of an anomoly:  with the both
+	 * edge detectors turned off, we still get an edge event on a
+	 * positive edge transition.  to take advantage of this, we use the
+	 * front-end inverter to ensure that that's the edge we're always
+	 * going to see next.
+	 */
+
+	int state;
+
+	state = cs5535_gpio_isset(OLPC_GPIO_LID, GPIO_READ_BACK);
+	lid_open = !state ^ !lid_inverted; /* x ^^ y */
+	if (!state)
+		return;
+
+	flip_lid_inverter();
+}
+
+/* Report current lid switch state through input layer */
+static void send_lid_state(void)
+{
+	input_report_switch(lid_switch_idev, SW_LID, !lid_open);
+	input_sync(lid_switch_idev);
+}
+
+static ssize_t lid_wake_mode_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	const char *mode = lid_wake_mode_names[lid_wake_mode];
+	return sprintf(buf, "%s\n", mode);
+}
+static ssize_t lid_wake_mode_set(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	int i;
+	for (i = 0; i < ARRAY_SIZE(lid_wake_mode_names); i++) {
+		const char *mode = lid_wake_mode_names[i];
+		if (strlen(mode) != count || strncasecmp(mode, buf, count))
+			continue;
+
+		lid_wake_mode = i;
+		return count;
+	}
+	return -EINVAL;
+}
+static DEVICE_ATTR(lid_wake_mode, S_IWUSR | S_IRUGO, lid_wake_mode_show,
+		   lid_wake_mode_set);
+
 /*
  * Process all items in the EC's SCI queue.
  *
@@ -111,6 +192,11 @@ static irqreturn_t xo1_sci_intr(int irq, void *dev_id)
 		schedule_work(&sci_work);
 	}
 
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_STS);
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_STS);
+	detect_lid_state();
+	send_lid_state();
+
 	return IRQ_HANDLED;
 }
 
@@ -126,11 +212,32 @@ static int xo1_sci_suspend(struct platform_device *pdev, pm_message_t state)
 	else
 		olpc_ec_wakeup_clear(EC_SCI_SRC_EBOOK);
 
+	if (!device_may_wakeup(&lid_switch_idev->dev)) {
+		cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+	} else if ((lid_open && lid_wake_mode == LID_WAKE_OPEN) ||
+		   (!lid_open && lid_wake_mode == LID_WAKE_CLOSE)) {
+		flip_lid_inverter();
+
+		/* we may have just caused an event */
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_STS);
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_STS);
+
+		cs5535_gpio_set(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+	}
+
 	return 0;
 }
 
 static int xo1_sci_resume(struct platform_device *pdev)
 {
+	/*
+	 * We don't know what may have happened while we were asleep.
+	 * Reestablish our lid setup so we're sure to catch all transitions.
+	 */
+	detect_lid_state();
+	send_lid_state();
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+
 	/* Enable all EC events */
 	olpc_ec_mask_write(EC_SCI_SRC_ALL);
 	return 0;
@@ -221,6 +328,43 @@ static void free_ec_sci(void)
 	gpio_free(OLPC_GPIO_ECSCI);
 }
 
+static int __devinit setup_lid_events(void)
+{
+	int r;
+
+	r = gpio_request(OLPC_GPIO_LID, "OLPC-LID");
+	if (r)
+		return r;
+
+	gpio_direction_input(OLPC_GPIO_LID);
+
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_INPUT_INVERT);
+	lid_inverted = 0;
+
+	/* Clear edge detection and event enable for now */
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_EN);
+	cs5535_gpio_clear(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_EN);
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_NEGATIVE_EDGE_STS);
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_POSITIVE_EDGE_STS);
+
+	/* Set the LID to cause an PME event on group 6 */
+	cs5535_gpio_setup_event(OLPC_GPIO_LID, 6, 1);
+
+	/* Set PME group 6 to fire the SCI interrupt */
+	cs5535_gpio_set_irq(6, sci_irq);
+
+	/* Enable the event */
+	cs5535_gpio_set(OLPC_GPIO_LID, GPIO_EVENTS_ENABLE);
+
+	return 0;
+}
+
+static void free_lid_events(void)
+{
+	gpio_free(OLPC_GPIO_LID);
+}
+
 static int __devinit setup_power_button(struct platform_device *pdev)
 {
 	int r;
@@ -283,6 +427,50 @@ static void free_ebook_switch(void)
 	input_free_device(ebook_switch_idev);
 }
 
+static int __devinit setup_lid_switch(struct platform_device *pdev)
+{
+	int r;
+
+	lid_switch_idev = input_allocate_device();
+	if (!lid_switch_idev)
+		return -ENOMEM;
+
+	lid_switch_idev->name = "Lid Switch";
+	lid_switch_idev->phys = DRV_NAME "/input2";
+	set_bit(EV_SW, lid_switch_idev->evbit);
+	set_bit(SW_LID, lid_switch_idev->swbit);
+
+	lid_switch_idev->dev.parent = &pdev->dev;
+	device_set_wakeup_capable(&lid_switch_idev->dev, true);
+
+	r = input_register_device(lid_switch_idev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to register lid switch: %d\n", r);
+		goto err_register;
+	}
+
+	r = device_create_file(&lid_switch_idev->dev, &dev_attr_lid_wake_mode);
+	if (r) {
+		dev_err(&pdev->dev, "failed to create wake mode attr: %d\n", r);
+		goto err_create_attr;
+	}
+
+	return 0;
+
+err_create_attr:
+	input_unregister_device(lid_switch_idev);
+err_register:
+	input_free_device(lid_switch_idev);
+	return r;
+}
+
+static void free_lid_switch(void)
+{
+	device_remove_file(&lid_switch_idev->dev, &dev_attr_lid_wake_mode);
+	input_unregister_device(lid_switch_idev);
+	input_free_device(lid_switch_idev);
+}
+
 static int __devinit xo1_sci_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -311,12 +499,21 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 	if (r)
 		goto err_ebook;
 
+	r = setup_lid_switch(pdev);
+	if (r)
+		goto err_lid;
+
+	r = setup_lid_events();
+	if (r)
+		goto err_lidevt;
+
 	r = setup_ec_sci();
 	if (r)
 		goto err_ecsci;
 
 	/* Enable PME generation for EC-generated events */
-	outl(CS5536_GPIOM7_PME_EN, acpi_base + CS5536_PM_GPE0_EN);
+	outl(CS5536_GPIOM6_PME_EN | CS5536_GPIOM7_PME_EN,
+		acpi_base + CS5536_PM_GPE0_EN);
 
 	/* Clear pending events */
 	outl(0xffffffff, acpi_base + CS5536_PM_GPE0_STS);
@@ -324,6 +521,8 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 
 	/* Initial sync */
 	send_ebook_state();
+	detect_lid_state();
+	send_lid_state();
 
 	r = setup_sci_interrupt(pdev);
 	if (r)
@@ -337,6 +536,10 @@ static int __devinit xo1_sci_probe(struct platform_device *pdev)
 err_sci:
 	free_ec_sci();
 err_ecsci:
+	free_lid_events();
+err_lidevt:
+	free_lid_switch();
+err_lid:
 	free_ebook_switch();
 err_ebook:
 	free_power_button();
@@ -349,6 +552,8 @@ static int __devexit xo1_sci_remove(struct platform_device *pdev)
 	free_irq(sci_irq, pdev);
 	cancel_work_sync(&sci_work);
 	free_ec_sci();
+	free_lid_events();
+	free_lid_switch();
 	free_ebook_switch();
 	free_power_button();
 	acpi_base = 0;
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index d7e9a7f..72954c6 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -102,6 +102,7 @@ static inline int cs5535_pic_unreqz_select_high(unsigned int group,
 
 /* CS5536_PM_GPE0_EN bits */
 #define CS5536_GPIOM7_PME_EN	(1 << 31)
+#define CS5536_GPIOM6_PME_EN	(1 << 30)
 
 /* VSA2 magic values */
 #define VSA_VRC_INDEX		0xAC1C

[PATCH v3 09/11] x86, olpc-xo1-sci: Propagate power supply/battery events

[Daniel Drake]

EC events indicate change in AC power connectivity, battery state of
charge, battery error, battery presence, etc. Send notifications to
the power supply subsystem when changes are detected.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                      |    4 ++-
 arch/x86/platform/olpc/olpc-xo1-sci.c |   37 +++++++++++++++++++++++++++++++++
 2 files changed, 40 insertions(+), 1 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index f5bc969..38af371 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2084,7 +2084,7 @@ config OLPC_XO1_PM
 
 config OLPC_XO1_SCI
 	bool "OLPC XO-1 SCI extras"
-	depends on OLPC && OLPC_XO1_PM
+	depends on OLPC && OLPC_XO1_PM && POWER_SUPPLY
 	select GPIO_CS5535
 	select MFD_CORE
 	---help---
@@ -2093,6 +2093,8 @@ config OLPC_XO1_SCI
 	   - Power button
 	   - Ebook switch
 	   - Lid switch
+	   - AC adapter status updates
+	   - Battery status updates
 
 endif # X86_32
 
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
index ad0670b..1d4c783 100644
--- a/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -19,6 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
+#include <linux/power_supply.h>
 #include <linux/suspend.h>
 #include <linux/workqueue.h>
 
@@ -52,6 +53,26 @@ static const char * const lid_wake_mode_names[] = {
 	[LID_WAKE_CLOSE] = "close",
 };
 
+static void battery_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-battery");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
+static void ac_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-ac");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
 /* Report current ebook switch state through input layer */
 static void send_ebook_state(void)
 {
@@ -151,6 +172,18 @@ static void process_sci_queue(bool propagate_events)
 
 		pr_debug(PFX "SCI 0x%x received\n", data);
 
+		switch (data) {
+		case EC_SCI_SRC_BATERR:
+		case EC_SCI_SRC_BATSOC:
+		case EC_SCI_SRC_BATTERY:
+		case EC_SCI_SRC_BATCRIT:
+			battery_status_changed();
+			break;
+		case EC_SCI_SRC_ACPWR:
+			ac_status_changed();
+			break;
+		}
+
 		if (data == EC_SCI_SRC_EBOOK && propagate_events)
 			send_ebook_state();
 	} while (data);
@@ -240,6 +273,10 @@ static int xo1_sci_resume(struct platform_device *pdev)
 
 	/* Enable all EC events */
 	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	/* Power/battery status might have changed too */
+	battery_status_changed();
+	ac_status_changed();
 	return 0;
 }
 
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc-xo1-sci: Propagate power supply/battery events

[tip-bot for Daniel Drake]

Commit-ID:  e1040ac693bac19eaeafbd6c5fd24d9429b5eeb8
Gitweb:     http://git.kernel.org/tip/e1040ac693bac19eaeafbd6c5fd24d9429b5eeb8
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:16 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:40 -0700

x86, olpc-xo1-sci: Propagate power supply/battery events

EC events indicate change in AC power connectivity, battery state of
charge, battery error, battery presence, etc. Send notifications to
the power supply subsystem when changes are detected.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-10-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                      |    4 ++-
 arch/x86/platform/olpc/olpc-xo1-sci.c |   37 +++++++++++++++++++++++++++++++++
 2 files changed, 40 insertions(+), 1 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 350ccbb..a6aefbb 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2082,7 +2082,7 @@ config OLPC_XO1_PM
 
 config OLPC_XO1_SCI
 	bool "OLPC XO-1 SCI extras"
-	depends on OLPC && OLPC_XO1_PM
+	depends on OLPC && OLPC_XO1_PM && POWER_SUPPLY
 	select GPIO_CS5535
 	select MFD_CORE
 	---help---
@@ -2091,6 +2091,8 @@ config OLPC_XO1_SCI
 	   - Power button
 	   - Ebook switch
 	   - Lid switch
+	   - AC adapter status updates
+	   - Battery status updates
 
 endif # X86_32
 
diff --git a/arch/x86/platform/olpc/olpc-xo1-sci.c b/arch/x86/platform/olpc/olpc-xo1-sci.c
index ad0670b..1d4c783 100644
--- a/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ b/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -19,6 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/mfd/core.h>
+#include <linux/power_supply.h>
 #include <linux/suspend.h>
 #include <linux/workqueue.h>
 
@@ -52,6 +53,26 @@ static const char * const lid_wake_mode_names[] = {
 	[LID_WAKE_CLOSE] = "close",
 };
 
+static void battery_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-battery");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
+static void ac_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-ac");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
 /* Report current ebook switch state through input layer */
 static void send_ebook_state(void)
 {
@@ -151,6 +172,18 @@ static void process_sci_queue(bool propagate_events)
 
 		pr_debug(PFX "SCI 0x%x received\n", data);
 
+		switch (data) {
+		case EC_SCI_SRC_BATERR:
+		case EC_SCI_SRC_BATSOC:
+		case EC_SCI_SRC_BATTERY:
+		case EC_SCI_SRC_BATCRIT:
+			battery_status_changed();
+			break;
+		case EC_SCI_SRC_ACPWR:
+			ac_status_changed();
+			break;
+		}
+
 		if (data == EC_SCI_SRC_EBOOK && propagate_events)
 			send_ebook_state();
 	} while (data);
@@ -240,6 +273,10 @@ static int xo1_sci_resume(struct platform_device *pdev)
 
 	/* Enable all EC events */
 	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	/* Power/battery status might have changed too */
+	battery_status_changed();
+	ac_status_changed();
 	return 0;
 }
 

[PATCH v3 10/11] x86, olpc: Add XO-1 RTC driver

[Daniel Drake]

Add a driver to configure the XO-1 RTC via CS5536 MSRs, to be used as a
system wakeup source via olpc-xo1-pm.

Device detection is based on finding the relevant device tree node.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devicetree-discuss@lists.ozlabs.org
---
 .../devicetree/bindings/rtc/olpc-xo1-rtc.txt       |    5 +
 arch/x86/Kconfig                                   |    7 ++
 arch/x86/platform/olpc/Makefile                    |    1 +
 arch/x86/platform/olpc/olpc-xo1-rtc.c              |   82 ++++++++++++++++++++
 include/linux/cs5535.h                             |    5 +
 5 files changed, 100 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt
 create mode 100644 arch/x86/platform/olpc/olpc-xo1-rtc.c

diff --git a/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt b/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt
new file mode 100644
index 0000000..a2891ce
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt
@@ -0,0 +1,5 @@
+OLPC XO-1 RTC
+~~~~~~~~~~~~~
+
+Required properties:
+ - compatible : "olpc,xo1-rtc"
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 38af371..de81496 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2082,6 +2082,13 @@ config OLPC_XO1_PM
 	---help---
 	  Add support for poweroff and suspend of the OLPC XO-1 laptop.
 
+config OLPC_XO1_RTC
+	bool "OLPC XO-1 Real Time Clock"
+	depends on OLPC_XO1_PM && RTC_DRV_CMOS
+	---help---
+	  Add support for the XO-1 real time clock, which can be used as a
+	  programmable wakeup source.
+
 config OLPC_XO1_SCI
 	bool "OLPC XO-1 SCI extras"
 	depends on OLPC && OLPC_XO1_PM && POWER_SUPPLY
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 1ec5ade..8922b9b 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,3 +1,4 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
 obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
+obj-$(CONFIG_OLPC_XO1_RTC)	+= olpc-xo1-rtc.o
 obj-$(CONFIG_OLPC_XO1_SCI)	+= olpc-xo1-sci.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-rtc.c b/arch/x86/platform/olpc/olpc-xo1-rtc.c
new file mode 100644
index 0000000..476cc98
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo1-rtc.c
@@ -0,0 +1,82 @@
+/*
+ * Support for OLPC XO-1 Real Time Clock (RTC)
+ *
+ * Copyright (C) 2011 One Laptop per Child
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/mc146818rtc.h>
+#include <linux/platform_device.h>
+#include <linux/rtc.h>
+#include <linux/of.h>
+
+#include <asm/msr.h>
+#include <asm/olpc.h>
+
+static void rtc_wake_on(struct device *dev)
+{
+	olpc_xo1_pm_wakeup_set(CS5536_PM_RTC);
+}
+
+static void rtc_wake_off(struct device *dev)
+{
+	olpc_xo1_pm_wakeup_clear(CS5536_PM_RTC);
+}
+
+static struct resource rtc_platform_resource[] = {
+	[0] = {
+		.start	= RTC_PORT(0),
+		.end	= RTC_PORT(1),
+		.flags	= IORESOURCE_IO,
+	},
+	[1] = {
+		.start	= RTC_IRQ,
+		.end	= RTC_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct cmos_rtc_board_info rtc_info = {
+	.rtc_day_alarm = 0,
+	.rtc_mon_alarm = 0,
+	.rtc_century = 0,
+	.wake_on = rtc_wake_on,
+	.wake_off = rtc_wake_off,
+};
+
+static struct platform_device xo1_rtc_device = {
+	.name = "rtc_cmos",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(rtc_platform_resource),
+	.dev.platform_data = &rtc_info,
+	.resource = rtc_platform_resource,
+};
+
+static int __init xo1_rtc_init(void)
+{
+	int r;
+	struct device_node *node;
+
+	node = of_find_compatible_node(NULL, NULL, "olpc,xo1-rtc");
+	if (!node)
+		return 0;
+	of_node_put(node);
+
+	pr_info("olpc-xo1-rtc: Initializing OLPC XO-1 RTC\n");
+	rdmsrl(MSR_RTC_DOMA_OFFSET, rtc_info.rtc_day_alarm);
+	rdmsrl(MSR_RTC_MONA_OFFSET, rtc_info.rtc_mon_alarm);
+	rdmsrl(MSR_RTC_CEN_OFFSET, rtc_info.rtc_century);
+
+	r = platform_device_register(&xo1_rtc_device);
+	if (r)
+		return r;
+
+	device_init_wakeup(&xo1_rtc_device.dev, 1);
+	return 0;
+}
+arch_initcall(xo1_rtc_init);
+
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 72954c6..c077aec 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -40,6 +40,10 @@
 #define MSR_MFGPT_NR		0x51400029
 #define MSR_MFGPT_SETUP		0x5140002B
 
+#define MSR_RTC_DOMA_OFFSET	0x51400055
+#define MSR_RTC_MONA_OFFSET	0x51400056
+#define MSR_RTC_CEN_OFFSET	0x51400057
+
 #define MSR_LX_SPARE_MSR	0x80000011	/* DC-specific */
 
 #define MSR_GX_GLD_MSR_CONFIG	0xC0002001
@@ -95,6 +99,7 @@ static inline int cs5535_pic_unreqz_select_high(unsigned int group,
 
 /* CS5536_PM1_EN bits */
 #define CS5536_PM_PWRBTN	(1 << 8)
+#define CS5536_PM_RTC		(1 << 10)
 
 /* CS5536_PM_GPE0_STS bits */
 #define CS5536_GPIOM7_PME_FLAG	(1 << 31)
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Add XO-1 RTC driver

[tip-bot for Daniel Drake]

Commit-ID:  cfee95977bea090ae5ec4fd442ebd381792d46c4
Gitweb:     http://git.kernel.org/tip/cfee95977bea090ae5ec4fd442ebd381792d46c4
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:17 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:42 -0700

x86, olpc: Add XO-1 RTC driver

Add a driver to configure the XO-1 RTC via CS5536 MSRs, to be used as a
system wakeup source via olpc-xo1-pm.

Device detection is based on finding the relevant device tree node.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-11-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 .../devicetree/bindings/rtc/olpc-xo1-rtc.txt       |    5 +
 arch/x86/Kconfig                                   |    7 ++
 arch/x86/platform/olpc/Makefile                    |    1 +
 arch/x86/platform/olpc/olpc-xo1-rtc.c              |   81 ++++++++++++++++++++
 include/linux/cs5535.h                             |    5 +
 5 files changed, 99 insertions(+), 0 deletions(-)

diff --git a/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt b/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt
new file mode 100644
index 0000000..a2891ce
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt
@@ -0,0 +1,5 @@
+OLPC XO-1 RTC
+~~~~~~~~~~~~~
+
+Required properties:
+ - compatible : "olpc,xo1-rtc"
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index a6aefbb..0a9d573 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2080,6 +2080,13 @@ config OLPC_XO1_PM
 	---help---
 	  Add support for poweroff and suspend of the OLPC XO-1 laptop.
 
+config OLPC_XO1_RTC
+	bool "OLPC XO-1 Real Time Clock"
+	depends on OLPC_XO1_PM && RTC_DRV_CMOS
+	---help---
+	  Add support for the XO-1 real time clock, which can be used as a
+	  programmable wakeup source.
+
 config OLPC_XO1_SCI
 	bool "OLPC XO-1 SCI extras"
 	depends on OLPC && OLPC_XO1_PM && POWER_SUPPLY
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 1ec5ade..8922b9b 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -1,3 +1,4 @@
 obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
 obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
+obj-$(CONFIG_OLPC_XO1_RTC)	+= olpc-xo1-rtc.o
 obj-$(CONFIG_OLPC_XO1_SCI)	+= olpc-xo1-sci.o
diff --git a/arch/x86/platform/olpc/olpc-xo1-rtc.c b/arch/x86/platform/olpc/olpc-xo1-rtc.c
new file mode 100644
index 0000000..a2b4efd
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo1-rtc.c
@@ -0,0 +1,81 @@
+/*
+ * Support for OLPC XO-1 Real Time Clock (RTC)
+ *
+ * Copyright (C) 2011 One Laptop per Child
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/mc146818rtc.h>
+#include <linux/platform_device.h>
+#include <linux/rtc.h>
+#include <linux/of.h>
+
+#include <asm/msr.h>
+#include <asm/olpc.h>
+
+static void rtc_wake_on(struct device *dev)
+{
+	olpc_xo1_pm_wakeup_set(CS5536_PM_RTC);
+}
+
+static void rtc_wake_off(struct device *dev)
+{
+	olpc_xo1_pm_wakeup_clear(CS5536_PM_RTC);
+}
+
+static struct resource rtc_platform_resource[] = {
+	[0] = {
+		.start	= RTC_PORT(0),
+		.end	= RTC_PORT(1),
+		.flags	= IORESOURCE_IO,
+	},
+	[1] = {
+		.start	= RTC_IRQ,
+		.end	= RTC_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct cmos_rtc_board_info rtc_info = {
+	.rtc_day_alarm = 0,
+	.rtc_mon_alarm = 0,
+	.rtc_century = 0,
+	.wake_on = rtc_wake_on,
+	.wake_off = rtc_wake_off,
+};
+
+static struct platform_device xo1_rtc_device = {
+	.name = "rtc_cmos",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(rtc_platform_resource),
+	.dev.platform_data = &rtc_info,
+	.resource = rtc_platform_resource,
+};
+
+static int __init xo1_rtc_init(void)
+{
+	int r;
+	struct device_node *node;
+
+	node = of_find_compatible_node(NULL, NULL, "olpc,xo1-rtc");
+	if (!node)
+		return 0;
+	of_node_put(node);
+
+	pr_info("olpc-xo1-rtc: Initializing OLPC XO-1 RTC\n");
+	rdmsrl(MSR_RTC_DOMA_OFFSET, rtc_info.rtc_day_alarm);
+	rdmsrl(MSR_RTC_MONA_OFFSET, rtc_info.rtc_mon_alarm);
+	rdmsrl(MSR_RTC_CEN_OFFSET, rtc_info.rtc_century);
+
+	r = platform_device_register(&xo1_rtc_device);
+	if (r)
+		return r;
+
+	device_init_wakeup(&xo1_rtc_device.dev, 1);
+	return 0;
+}
+arch_initcall(xo1_rtc_init);
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
index 72954c6..c077aec 100644
--- a/include/linux/cs5535.h
+++ b/include/linux/cs5535.h
@@ -40,6 +40,10 @@
 #define MSR_MFGPT_NR		0x51400029
 #define MSR_MFGPT_SETUP		0x5140002B
 
+#define MSR_RTC_DOMA_OFFSET	0x51400055
+#define MSR_RTC_MONA_OFFSET	0x51400056
+#define MSR_RTC_CEN_OFFSET	0x51400057
+
 #define MSR_LX_SPARE_MSR	0x80000011	/* DC-specific */
 
 #define MSR_GX_GLD_MSR_CONFIG	0xC0002001
@@ -95,6 +99,7 @@ static inline int cs5535_pic_unreqz_select_high(unsigned int group,
 
 /* CS5536_PM1_EN bits */
 #define CS5536_PM_PWRBTN	(1 << 8)
+#define CS5536_PM_RTC		(1 << 10)
 
 /* CS5536_PM_GPE0_STS bits */
 #define CS5536_GPIOM7_PME_FLAG	(1 << 31)

[PATCH v3 11/11] x86, olpc: Add XO-1.5 SCI driver

[Daniel Drake]

Add a driver for the ACPI-based EC event interface found on the
OLPC XO-1.5 laptop. This enables notification of battery/AC power events,
and enables various devices to be used as wakeup sources through regular
ACPI mechanisms.

This driver can't be built as a module, because some drivers need to know
at boot-time if SCI-based functionality is available via
olpc_ec_wakeup_available().

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
---
 arch/x86/Kconfig                       |    9 ++
 arch/x86/platform/olpc/Makefile        |    1 +
 arch/x86/platform/olpc/olpc-xo15-sci.c |  168 ++++++++++++++++++++++++++++++++
 arch/x86/platform/olpc/olpc.c          |    9 ++
 4 files changed, 187 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/platform/olpc/olpc-xo15-sci.c

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index de81496..1ed7d32 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2103,6 +2103,15 @@ config OLPC_XO1_SCI
 	   - AC adapter status updates
 	   - Battery status updates
 
+config OLPC_XO15_SCI
+	bool "OLPC XO-1.5 SCI extras"
+	depends on OLPC && ACPI && POWER_SUPPLY
+	---help---
+	  Add support for SCI-based features of the OLPC XO-1.5 laptop:
+	   - EC-driven system wakeups
+	   - AC adapter status updates
+	   - Battery status updates
+
 endif # X86_32
 
 config AMD_NB
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 8922b9b..fd332c5 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -2,3 +2,4 @@ obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
 obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
 obj-$(CONFIG_OLPC_XO1_RTC)	+= olpc-xo1-rtc.o
 obj-$(CONFIG_OLPC_XO1_SCI)	+= olpc-xo1-sci.o
+obj-$(CONFIG_OLPC_XO15_SCI)	+= olpc-xo15-sci.o
diff --git a/arch/x86/platform/olpc/olpc-xo15-sci.c b/arch/x86/platform/olpc/olpc-xo15-sci.c
new file mode 100644
index 0000000..a5990eb
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo15-sci.c
@@ -0,0 +1,168 @@
+/*
+ * Support for OLPC XO-1.5 System Control Interrupts (SCI)
+ *
+ * Copyright (C) 2009-2010 One Laptop per Child
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+#include <linux/power_supply.h>
+
+#include <acpi/acpi_bus.h>
+#include <acpi/acpi_drivers.h>
+#include <asm/olpc.h>
+
+#define DRV_NAME			"olpc-xo15-sci"
+#define PFX				DRV_NAME ": "
+#define XO15_SCI_CLASS			DRV_NAME
+#define XO15_SCI_DEVICE_NAME		"OLPC XO-1.5 SCI"
+
+static unsigned long xo15_sci_gpe;
+
+static void battery_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-battery");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
+static void ac_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-ac");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
+static void process_sci_queue(void)
+{
+	u16 data;
+	int r;
+
+	do {
+		r = olpc_ec_sci_query(&data);
+		if (r || !data)
+			break;
+
+		pr_debug(PFX "SCI 0x%x received\n", data);
+
+		switch (data) {
+		case EC_SCI_SRC_BATERR:
+		case EC_SCI_SRC_BATSOC:
+		case EC_SCI_SRC_BATTERY:
+		case EC_SCI_SRC_BATCRIT:
+			battery_status_changed();
+			break;
+		case EC_SCI_SRC_ACPWR:
+			ac_status_changed();
+			break;
+		}
+	} while (data);
+
+	if (r)
+		pr_err(PFX "Failed to clear SCI queue");
+}
+
+static void process_sci_queue_work(struct work_struct *work)
+{
+	process_sci_queue();
+}
+
+static DECLARE_WORK(sci_work, process_sci_queue_work);
+
+static u32 xo15_sci_gpe_handler(acpi_handle gpe_device, u32 gpe, void *context)
+{
+	schedule_work(&sci_work);
+	return ACPI_INTERRUPT_HANDLED | ACPI_REENABLE_GPE;
+}
+
+static int xo15_sci_add(struct acpi_device *device)
+{
+	unsigned long long tmp;
+	acpi_status status;
+
+	if (!device)
+		return -EINVAL;
+
+	strcpy(acpi_device_name(device), XO15_SCI_DEVICE_NAME);
+	strcpy(acpi_device_class(device), XO15_SCI_CLASS);
+
+	/* Get GPE bit assignment (EC events). */
+	status = acpi_evaluate_integer(device->handle, "_GPE", NULL, &tmp);
+	if (ACPI_FAILURE(status))
+		return -EINVAL;
+
+	xo15_sci_gpe = tmp;
+	status = acpi_install_gpe_handler(NULL, xo15_sci_gpe,
+					  ACPI_GPE_EDGE_TRIGGERED,
+					  xo15_sci_gpe_handler, device);
+	if (ACPI_FAILURE(status))
+		return -ENODEV;
+
+	dev_info(&device->dev, "Initialized, GPE = 0x%lx\n", xo15_sci_gpe);
+
+	/* Flush queue, and enable all SCI events */
+	process_sci_queue();
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	acpi_enable_gpe(NULL, xo15_sci_gpe);
+
+	/* Enable wake-on-EC */
+	if (device->wakeup.flags.valid)
+		device_set_wakeup_enable(&device->dev, true);
+
+	return 0;
+}
+
+static int xo15_sci_remove(struct acpi_device *device, int type)
+{
+	acpi_disable_gpe(NULL, xo15_sci_gpe);
+	acpi_remove_gpe_handler(NULL, xo15_sci_gpe, xo15_sci_gpe_handler);
+	cancel_work_sync(&sci_work);
+	return 0;
+}
+
+static int xo15_sci_resume(struct acpi_device *device)
+{
+	/* Enable all EC events */
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	/* Power/battery status might have changed */
+	battery_status_changed();
+	ac_status_changed();
+
+	return 0;
+}
+
+static const struct acpi_device_id xo15_sci_device_ids[] = {
+	{"XO15EC", 0},
+	{"", 0},
+};
+
+static struct acpi_driver xo15_sci_drv = {
+	.name = DRV_NAME,
+	.class = XO15_SCI_CLASS,
+	.ids = xo15_sci_device_ids,
+	.ops = {
+		.add = xo15_sci_add,
+		.remove = xo15_sci_remove,
+		.resume = xo15_sci_resume,
+	},
+};
+
+static int __init xo15_sci_init(void)
+{
+	return acpi_bus_register_driver(&xo15_sci_drv);
+}
+device_initcall(xo15_sci_init);
diff --git a/arch/x86/platform/olpc/olpc.c b/arch/x86/platform/olpc/olpc.c
index 72fd041..8b9940e 100644
--- a/arch/x86/platform/olpc/olpc.c
+++ b/arch/x86/platform/olpc/olpc.c
@@ -222,6 +222,15 @@ bool olpc_ec_wakeup_available(void)
 		return true;
 #endif
 
+	/*
+	 * XO-1.5 EC wakeups are available when olpc-xo15-sci driver is
+	 * compiled in
+	 */
+#ifdef CONFIG_OLPC_XO15_SCI
+	if (olpc_platform_info.boardrev >= olpc_board_pre(0xd0)) /* XO-1.5 */
+		return true;
+#endif
+
 	return false;
 }
 EXPORT_SYMBOL_GPL(olpc_ec_wakeup_available);
-- 
1.7.5.4

[tip:x86/olpc] x86, olpc: Add XO-1.5 SCI driver

[tip-bot for Daniel Drake]

Commit-ID:  a0f30f592d2d81e28f3ed7fea7f03246b0d55b75
Gitweb:     http://git.kernel.org/tip/a0f30f592d2d81e28f3ed7fea7f03246b0d55b75
Author:     Daniel Drake <dsd@laptop.org>
AuthorDate: Sat, 25 Jun 2011 17:34:18 +0100
Committer:  H. Peter Anvin <hpa@linux.intel.com>
CommitDate: Wed, 6 Jul 2011 14:44:43 -0700

x86, olpc: Add XO-1.5 SCI driver

Add a driver for the ACPI-based EC event interface found on the
OLPC XO-1.5 laptop. This enables notification of battery/AC power events,
and enables various devices to be used as wakeup sources through regular
ACPI mechanisms.

This driver can't be built as a module, because some drivers need to know
at boot-time if SCI-based functionality is available via
olpc_ec_wakeup_available().

Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-12-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
---
 arch/x86/Kconfig                       |    9 ++
 arch/x86/platform/olpc/Makefile        |    1 +
 arch/x86/platform/olpc/olpc-xo15-sci.c |  168 ++++++++++++++++++++++++++++++++
 arch/x86/platform/olpc/olpc.c          |    9 ++
 4 files changed, 187 insertions(+), 0 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 0a9d573..8af5ba8 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -2101,6 +2101,15 @@ config OLPC_XO1_SCI
 	   - AC adapter status updates
 	   - Battery status updates
 
+config OLPC_XO15_SCI
+	bool "OLPC XO-1.5 SCI extras"
+	depends on OLPC && ACPI && POWER_SUPPLY
+	---help---
+	  Add support for SCI-based features of the OLPC XO-1.5 laptop:
+	   - EC-driven system wakeups
+	   - AC adapter status updates
+	   - Battery status updates
+
 endif # X86_32
 
 config AMD_NB
diff --git a/arch/x86/platform/olpc/Makefile b/arch/x86/platform/olpc/Makefile
index 8922b9b..fd332c5 100644
--- a/arch/x86/platform/olpc/Makefile
+++ b/arch/x86/platform/olpc/Makefile
@@ -2,3 +2,4 @@ obj-$(CONFIG_OLPC)		+= olpc.o olpc_ofw.o olpc_dt.o
 obj-$(CONFIG_OLPC_XO1_PM)		+= olpc-xo1-pm.o xo1-wakeup.o
 obj-$(CONFIG_OLPC_XO1_RTC)	+= olpc-xo1-rtc.o
 obj-$(CONFIG_OLPC_XO1_SCI)	+= olpc-xo1-sci.o
+obj-$(CONFIG_OLPC_XO15_SCI)	+= olpc-xo15-sci.o
diff --git a/arch/x86/platform/olpc/olpc-xo15-sci.c b/arch/x86/platform/olpc/olpc-xo15-sci.c
new file mode 100644
index 0000000..a5990eb
--- /dev/null
+++ b/arch/x86/platform/olpc/olpc-xo15-sci.c
@@ -0,0 +1,168 @@
+/*
+ * Support for OLPC XO-1.5 System Control Interrupts (SCI)
+ *
+ * Copyright (C) 2009-2010 One Laptop per Child
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+#include <linux/power_supply.h>
+
+#include <acpi/acpi_bus.h>
+#include <acpi/acpi_drivers.h>
+#include <asm/olpc.h>
+
+#define DRV_NAME			"olpc-xo15-sci"
+#define PFX				DRV_NAME ": "
+#define XO15_SCI_CLASS			DRV_NAME
+#define XO15_SCI_DEVICE_NAME		"OLPC XO-1.5 SCI"
+
+static unsigned long xo15_sci_gpe;
+
+static void battery_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-battery");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
+static void ac_status_changed(void)
+{
+	struct power_supply *psy = power_supply_get_by_name("olpc-ac");
+
+	if (psy) {
+		power_supply_changed(psy);
+		put_device(psy->dev);
+	}
+}
+
+static void process_sci_queue(void)
+{
+	u16 data;
+	int r;
+
+	do {
+		r = olpc_ec_sci_query(&data);
+		if (r || !data)
+			break;
+
+		pr_debug(PFX "SCI 0x%x received\n", data);
+
+		switch (data) {
+		case EC_SCI_SRC_BATERR:
+		case EC_SCI_SRC_BATSOC:
+		case EC_SCI_SRC_BATTERY:
+		case EC_SCI_SRC_BATCRIT:
+			battery_status_changed();
+			break;
+		case EC_SCI_SRC_ACPWR:
+			ac_status_changed();
+			break;
+		}
+	} while (data);
+
+	if (r)
+		pr_err(PFX "Failed to clear SCI queue");
+}
+
+static void process_sci_queue_work(struct work_struct *work)
+{
+	process_sci_queue();
+}
+
+static DECLARE_WORK(sci_work, process_sci_queue_work);
+
+static u32 xo15_sci_gpe_handler(acpi_handle gpe_device, u32 gpe, void *context)
+{
+	schedule_work(&sci_work);
+	return ACPI_INTERRUPT_HANDLED | ACPI_REENABLE_GPE;
+}
+
+static int xo15_sci_add(struct acpi_device *device)
+{
+	unsigned long long tmp;
+	acpi_status status;
+
+	if (!device)
+		return -EINVAL;
+
+	strcpy(acpi_device_name(device), XO15_SCI_DEVICE_NAME);
+	strcpy(acpi_device_class(device), XO15_SCI_CLASS);
+
+	/* Get GPE bit assignment (EC events). */
+	status = acpi_evaluate_integer(device->handle, "_GPE", NULL, &tmp);
+	if (ACPI_FAILURE(status))
+		return -EINVAL;
+
+	xo15_sci_gpe = tmp;
+	status = acpi_install_gpe_handler(NULL, xo15_sci_gpe,
+					  ACPI_GPE_EDGE_TRIGGERED,
+					  xo15_sci_gpe_handler, device);
+	if (ACPI_FAILURE(status))
+		return -ENODEV;
+
+	dev_info(&device->dev, "Initialized, GPE = 0x%lx\n", xo15_sci_gpe);
+
+	/* Flush queue, and enable all SCI events */
+	process_sci_queue();
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	acpi_enable_gpe(NULL, xo15_sci_gpe);
+
+	/* Enable wake-on-EC */
+	if (device->wakeup.flags.valid)
+		device_set_wakeup_enable(&device->dev, true);
+
+	return 0;
+}
+
+static int xo15_sci_remove(struct acpi_device *device, int type)
+{
+	acpi_disable_gpe(NULL, xo15_sci_gpe);
+	acpi_remove_gpe_handler(NULL, xo15_sci_gpe, xo15_sci_gpe_handler);
+	cancel_work_sync(&sci_work);
+	return 0;
+}
+
+static int xo15_sci_resume(struct acpi_device *device)
+{
+	/* Enable all EC events */
+	olpc_ec_mask_write(EC_SCI_SRC_ALL);
+
+	/* Power/battery status might have changed */
+	battery_status_changed();
+	ac_status_changed();
+
+	return 0;
+}
+
+static const struct acpi_device_id xo15_sci_device_ids[] = {
+	{"XO15EC", 0},
+	{"", 0},
+};
+
+static struct acpi_driver xo15_sci_drv = {
+	.name = DRV_NAME,
+	.class = XO15_SCI_CLASS,
+	.ids = xo15_sci_device_ids,
+	.ops = {
+		.add = xo15_sci_add,
+		.remove = xo15_sci_remove,
+		.resume = xo15_sci_resume,
+	},
+};
+
+static int __init xo15_sci_init(void)
+{
+	return acpi_bus_register_driver(&xo15_sci_drv);
+}
+device_initcall(xo15_sci_init);
diff --git a/arch/x86/platform/olpc/olpc.c b/arch/x86/platform/olpc/olpc.c
index 72fd041..8b9940e 100644
--- a/arch/x86/platform/olpc/olpc.c
+++ b/arch/x86/platform/olpc/olpc.c
@@ -222,6 +222,15 @@ bool olpc_ec_wakeup_available(void)
 		return true;
 #endif
 
+	/*
+	 * XO-1.5 EC wakeups are available when olpc-xo15-sci driver is
+	 * compiled in
+	 */
+#ifdef CONFIG_OLPC_XO15_SCI
+	if (olpc_platform_info.boardrev >= olpc_board_pre(0xd0)) /* XO-1.5 */
+		return true;
+#endif
+
 	return false;
 }
 EXPORT_SYMBOL_GPL(olpc_ec_wakeup_available);