From: "Jernej Škrabec" <jernej.skrabec@gmail.com>
To: Linus Walleij <linusw@kernel.org>, linux-sunxi@lists.linux.dev
Cc: Chen-Yu Tsai <wens@kernel.org>,
Samuel Holland <samuel@sholland.org>,
linux-gpio@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
Yang Siyuan <hsyysy@163.com>
Subject: Re: [PATCH v3 RESEND] pinctrl: sunxi: request the per-bank supply optionally
Date: Tue, 17 Nov 2026 17:17:25 +0100 [thread overview]
Message-ID: <uNcaWoiORlCb9uOBOQgmvw@gmail.com> (raw)
In-Reply-To: <20261117091944.12082-1-hsyysy@163.com>
Dne torek, 17. november 2026 ob 10:19:44 Srednjeevropski standardni čas je Yang Siyuan napisal(a):
> The per-bank "vcc-pX" supplies are optional in the device tree: the
> binding documents them, but notes that many boards do not describe them.
> sunxi_pmx_request() uses regulator_get() anyway, so the regulator core
> falls back to a dummy regulator and warns for every bank that has no
> supply:
>
> sun50i-h616-r-pinctrl 7022000.pinctrl: supply vcc-pl not found, using
> dummy regulator
>
> The H616 R_PIO is such a controller, and its PL0/PL1 pins drive the
> R_I2C bus, so every H616 board hits the warning during boot.
>
> Use of_regulator_get_optional() instead. A bank supply that is described
> in the device tree is still acquired and enabled, as it powers the
> physical VCC-Px rail, but one that is absent is skipped without a
> warning.
>
> The OF-only lookup matters here: regulator_get_optional() also falls back
> to a global regulator-name lookup. If a regulator with the same name as
> an absent bank supply is registered later, a subsequent pin request in
> that bank could acquire it and start the per-bank refcount at one, after
> earlier pins in the bank had already been requested without a regulator.
> Freeing any of those pins would then disable the supply while other pins
> in the bank are still active. Restricting the lookup to the pinctrl node
> makes an absent supply permanent; record that state so later pin requests
> do not retry the lookup. The refcount therefore stays balanced.
>
> Signed-off-by: Yang Siyuan <hsyysy@163.com>
> ---
>
> Changes in v3:
> - Use of_regulator_get_optional() instead of regulator_get_optional().
> The latter still performs a global regulator-name lookup, which can
> bind an unrelated regulator that appears after some pins were already
> requested and unbalance the per-bank refcount.
> - Remember that a bank has no supply so later pin requests skip the
> lookup, and keep the existing no-regulator check in sunxi_pmx_free().
Remembering IMO isn't worth it. It complicates the code which runs only
at probe time.
Best regards,
Jernej
> - Link to v2: https://lore.kernel.org/linux-gpio/20261026152027.1417178-1-hsyysy@163.com/
> - Link to v1: https://lore.kernel.org/linux-gpio/20261026144751.1392715-1-hsyysy@163.com/
> ---
> ---
> drivers/pinctrl/sunxi/pinctrl-sunxi.c | 29 +++++++++++++++++++++++++--
> drivers/pinctrl/sunxi/pinctrl-sunxi.h | 1 +
> 2 files changed, 28 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
> index 70099052d..d2345a85a 100644
> --- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c
> +++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
> @@ -913,23 +913,44 @@ static int sunxi_pmx_request(struct pinctrl_dev *pctldev, unsigned offset)
> PINS_PER_BANK;
> struct sunxi_pinctrl_regulator *s_reg = &pctl->regulators[bank_offset];
> struct regulator *reg = s_reg->regulator;
> + struct device_node *np = dev_of_node(pctl->dev);
> char supply[16];
> int ret;
>
> if (WARN_ON_ONCE(bank_offset >= ARRAY_SIZE(pctl->regulators)))
> return -EINVAL;
>
> + if (s_reg->supply_absent)
> + return 0;
> +
> if (reg) {
> refcount_inc(&s_reg->refcount);
> return 0;
> }
>
> + if (!np) {
> + s_reg->supply_absent = true;
> + return 0;
> + }
> +
> snprintf(supply, sizeof(supply), "vcc-p%c", 'a' + bank);
> - reg = regulator_get(pctl->dev, supply);
> - if (IS_ERR(reg))
> + /*
> + * Use the OF-only lookup: regulator_get_optional() would also match
> + * a same-named regulator from another device. Such a regulator can
> + * appear after some pins in this bank have already been requested,
> + * which would unbalance the per-bank refcount.
> + */
> + reg = of_regulator_get_optional(pctl->dev, np, supply);
> + if (IS_ERR(reg)) {
> + if (PTR_ERR(reg) == -ENODEV) {
> + s_reg->supply_absent = true;
> + return 0;
> + }
> +
> return dev_err_probe(pctl->dev, PTR_ERR(reg),
> "Couldn't get bank P%c regulator\n",
> 'A' + bank);
> + }
>
> ret = regulator_enable(reg);
> if (ret) {
> @@ -959,6 +980,10 @@ static int sunxi_pmx_free(struct pinctrl_dev *pctldev, unsigned offset)
> PINS_PER_BANK;
> struct sunxi_pinctrl_regulator *s_reg = &pctl->regulators[bank_offset];
>
> + /* The per-bank supply is optional, so this bank may not have one. */
> + if (!s_reg->regulator)
> + return 0;
> +
> if (!refcount_dec_and_test(&s_reg->refcount))
> return 0;
>
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.h b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
> index 8bd00c6ff..651249b23 100644
> --- a/drivers/pinctrl/sunxi/pinctrl-sunxi.h
> +++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
> @@ -162,6 +162,7 @@ struct sunxi_pinctrl_group {
> struct sunxi_pinctrl_regulator {
> struct regulator *regulator;
> refcount_t refcount;
> + bool supply_absent;
> };
>
> struct sunxi_pinctrl {
> base-commit: 091b06388b117fefdcb63336ac09956a4914b961
>
next prev parent reply other threads:[~2026-11-17 16:17 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-17 9:19 [PATCH v3 RESEND] pinctrl: sunxi: request the per-bank supply optionally Yang Siyuan
2026-11-17 16:17 ` Jernej Škrabec [this message]
2026-11-17 23:18 ` [PATCH v4] " Yang Siyuan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=uNcaWoiORlCb9uOBOQgmvw@gmail.com \
--to=jernej.skrabec@gmail.com \
--cc=hsyysy@163.com \
--cc=linusw@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=samuel@sholland.org \
--cc=wens@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.