From: Mark Eichin <eichin@thok.org>
To: Russell King <rmk@arm.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Subject: Re: CONFIG_BLK_DEV_SL82C105 should not be PPC/ARM specific
Date: 09 Sep 2001 02:49:20 -0400 [thread overview]
Message-ID: <xe1pu90svtb.fsf@swat.thok.org> (raw)
In-Reply-To: <20010906223001.A63F613DC7@kuroneko> <20010907000817.G23583@flint.arm.linux.org.uk>
In-Reply-To: Russell King's message of "Fri, 7 Sep 2001 00:08:17 +0100"
That patch (plus bludgeoning the config) certainly *works* on this
chipset, but it doesn't get DMA support; logs follow. If I run hdparm
to put it into using_dma mode, and then try to access it, using_dma
mode gets turned off after some delay...
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
W82C105: IDE controller on PCI bus 00 dev 10
PCI: No IRQ known for interrupt pin A of device 00:02.0. Probably
buggy MP table.
W82C105: chipset revision 6
W82C105: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 4W100H6, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 195711264 sectors (100204 MB) w/2048KiB Cache, CHS=194158/16/63,
(U)DMA
hda:hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
LDM: DEBUG (ldm.c, 876): validate_partition_table: Found basic MS-DOS
partition, not a
dynamic disk.
hda1 hda2
# hdparm -v /dev/hda
/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 63086/16/63, sectors = 195711264, start = 0
# hdparm -t /dev/hda
/dev/hda:
Timing buffered disk reads: 64 MB in 57.65 seconds = 1.11 MB/sec
# hdparm -v /dev/hda
/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 1 (on)
using_dma = 0 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 63086/16/63, sectors = 195711264, start = 0
prev parent reply other threads:[~2001-09-09 6:49 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-09-06 22:30 CONFIG_BLK_DEV_SL82C105 should not be PPC/ARM specific Mark W. Eichin
2001-09-06 23:08 ` Russell King
2001-09-09 6:49 ` Mark Eichin [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=xe1pu90svtb.fsf@swat.thok.org \
--to=eichin@thok.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rmk@arm.linux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.