From: Lee Revell <rlrevell@joe-job.com>
To: Edgar Toernig <froese@gmx.de>
Cc: linux-kernel@vger.kernel.org,
alsa-devel <alsa-devel@lists.sourceforge.net>
Subject: Re: 2.6.15 USB-Audio produces loud noise
Date: Thu, 05 Jan 2006 17:35:44 -0500 [thread overview]
Message-ID: <1136500545.847.61.camel@mindpipe> (raw)
In-Reply-To: <20060104205347.46f62718.froese@gmx.de>
[added alsa-devel to cc]
On Wed, 2006-01-04 at 20:53 +0100, Edgar Toernig wrote:
> Hi,
>
> my USB-speakers only work sporadical with 2.6.15. Sometimes everything's
> fine, sometimes they only produces loud noise as if the low and high bytes
> are swapped or the samples are not properly aligned. With 2.6.13 I never
> had this problem.
>
> This occures either with alsaplayer or with OSS apps using the kernel
> OSS emulation. Furthermore, it seems to be a startup problem. If
> playback starts correct it stays correct, if it starts wrong it stays
> wrong - at least as long as it keeps streaming. If playback is paused,
> the problem may trigger again.
>
> I tried UP, SMP (P4-HT), gcc-2.95, gcc-3.3.5 - no change. All drivers
> build in.
>
> [dmesg, lspci, and lsusb output below]
>
> Any fix known? I had a short look at the 2.6.13->15 diffs of usbaudio.c
> but they are rather big and I don't even know whether it's an USB or an
> Alsa problem...
>
> Ciao, ET.
>
>
> dmesg: (stripped)
>
> ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18
> ohci_hcd 0000:00:13.0: OHCI Host Controller
> drivers/usb/core/inode.c: creating file '002'
> ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:13.0: irq 18, io mem 0xec304000
> ohci_hcd 0000:00:13.0: resetting from state 'reset', control = 0x0
> ohci_hcd 0000:00:13.0: OHCI controller state
> ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
> ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
> ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
> ohci_hcd 0000:00:13.0: intrstatus 0x00000044 RHSC SF
> ohci_hcd 0000:00:13.0: intrenable 0x8000001a MIE UE RD WDH
> ohci_hcd 0000:00:13.0: hcca frame #0005
> ohci_hcd 0000:00:13.0: roothub.a 02000203 POTPGT=2 NPS NDP=3(3)
> ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
> ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
> ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
> ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00010100 CSC PPS
> ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS
> ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
> ohci_hcd 0000:00:13.0: created debug files
> usb usb2: default language 0x0409
> usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: OHCI Host Controller
> usb usb2: Manufacturer: Linux 2.6.15 ohci_hcd
> usb usb2: SerialNumber: 0000:00:13.0
> usb usb2: hotplug
> usb usb2: adding 2-0:1.0 (config #1, interface 0)
> usb 2-0:1.0: hotplug
> hub 2-0:1.0: usb_probe_interface
> hub 2-0:1.0: usb_probe_interface - got id
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> hub 2-0:1.0: standalone hub
> hub 2-0:1.0: no power switching (usb 1.0)
> hub 2-0:1.0: global over-current protection
> hub 2-0:1.0: power on to power good time: 4ms
> hub 2-0:1.0: local power source is good
> hub 2-0:1.0: no over-current condition exists
> hub 2-0:1.0: global over-current protection
> hub 2-0:1.0: power on to power good time: 4ms
> hub 2-0:1.0: local power source is good
> hub 2-0:1.0: no over-current condition exists
> hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PE
> S CCS
> usb 2-1: new full speed USB device using ohci_hcd and address 2
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PE
> S CCS
> usb 2-1: ep0 maxpacket = 8
> usb 2-1: skipped 4 descriptors after interface
> usb 2-1: skipped 2 descriptors after interface
> usb 2-1: skipped 1 descriptor after endpoint
> usb 2-1: default language 0x0409
> usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
> usb 2-1: Product: USB Audio
> usb 2-1: Manufacturer: C-Media INC.
> usb 2-1: hotplug
> usb 2-1: adding 2-1:1.0 (config #1, interface 0)
> usb 2-1:1.0: hotplug
> usb 2-1: adding 2-1:1.1 (config #1, interface 1)
> usb 2-1:1.1: hotplug
> drivers/usb/core/inode.c: creating file '002'
> Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21
> 2005 UTC).
> ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
> snd-usb-audio 2-1:1.0: usb_probe_interface
> snd-usb-audio 2-1:1.0: usb_probe_interface - got id
> usbcore: registered new driver snd-usb-audio
> ALSA device list:
> #0: ATI IXP rev 0 with ALC650F at 0xec305000, irq 17
> #1: C-Media INC. USB Audio at usb-0000:00:13.0-1, full speed
>
>
> lspci:
>
> 0000:00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01) (prog-if 10 [OHCI])
> Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device f362
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, cache line size 20
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at ec304000 (32-bit, non-prefetchable) [size=4K]
>
>
> lsusb:
>
> Bus 002 Device 002: ID 0d8c:0001 C-Media Electronics, Inc. USB Speaker
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 1.10
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 8
> idVendor 0x0d8c C-Media Electronics, Inc.
> idProduct 0x0001 USB Speaker
> bcdDevice 0.10
> iManufacturer 1 C-Media INC.
> iProduct 2 USB Audio
> iSerial 0
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 110
> bNumInterfaces 2
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0x80
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 0
> bInterfaceClass 1 Audio
> bInterfaceSubClass 1 Control Device
> bInterfaceProtocol 0
> iInterface 0
> AudioControl Interface Descriptor:
> bLength 9
> bDescriptorType 36
> bDescriptorSubtype 1 (HEADER)
> bcdADC 1.00
> wTotalLength 40
> bInCollection 1
> baInterfaceNr( 0) 1
> AudioControl Interface Descriptor:
> bLength 12
> bDescriptorType 36
> bDescriptorSubtype 2 (INPUT_TERMINAL)
> bTerminalID 1
> wTerminalType 0x0101 USB Streaming
> bAssocTerminal 0
> bNrChannels 2
> wChannelConfig 0x0003
> Left Front (L)
> Right Front (R)
> iChannelNames 0
> iTerminal 0
> AudioControl Interface Descriptor:
> bLength 10
> bDescriptorType 36
> bDescriptorSubtype 6 (FEATURE_UNIT)
> bUnitID 13
> bSourceID 1
> bControlSize 1
> bmaControls( 0) 0x03
> Mute
> Volume
> bmaControls( 1) 0x00
> bmaControls( 2) 0x00
> iFeature 0
> AudioControl Interface Descriptor:
> bLength 9
> bDescriptorType 36
> bDescriptorSubtype 3 (OUTPUT_TERMINAL)
> bTerminalID 3
> wTerminalType 0x0301 Speaker
> bAssocTerminal 0
> bSourceID 13
> iTerminal 0
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 1
> bAlternateSetting 0
> bNumEndpoints 0
> bInterfaceClass 1 Audio
> bInterfaceSubClass 2 Streaming
> bInterfaceProtocol 0
> iInterface 0
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 1
> bAlternateSetting 1
> bNumEndpoints 1
> bInterfaceClass 1 Audio
> bInterfaceSubClass 2 Streaming
> bInterfaceProtocol 0
> iInterface 0
> AudioStreaming Interface Descriptor:
> bLength 7
> bDescriptorType 36
> bDescriptorSubtype 1 (AS_GENERAL)
> bTerminalLink 1
> bDelay 1 frames
> wFormatTag 1 PCM
> AudioStreaming Interface Descriptor:
> bLength 11
> bDescriptorType 36
> bDescriptorSubtype 2 (FORMAT_TYPE)
> bFormatType 1 (FORMAT_TYPE_I)
> bNrChannels 2
> bSubframeSize 2
> bBitResolution 16
> bSamFreqType 1 Discrete
> tSamFreq[ 0] 48000
> Endpoint Descriptor:
> bLength 9
> bDescriptorType 5
> bEndpointAddress 0x06 EP 6 OUT
> bmAttributes 9
> Transfer Type Isochronous
> Synch Type Adaptive
> Usage Type Data
> wMaxPacketSize 0x00c0 1x 192 bytes
> bInterval 1
> bRefresh 0
> bSynchAddress 0
> AudioControl Endpoint Descriptor:
> bLength 7
> bDescriptorType 37
> bDescriptorSubtype 1 (EP_GENERAL)
> bmAttributes 0x00
> bLockDelayUnits 0 Undefined
> wLockDelay 0 Undefined
>
> EOF
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click
parent reply other threads:[~2006-01-05 22:35 UTC|newest]
Thread overview: expand[flat|nested] mbox.gz Atom feed
[parent not found: <20060104205347.46f62718.froese@gmx.de>]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1136500545.847.61.camel@mindpipe \
--to=rlrevell@joe-job.com \
--cc=alsa-devel@lists.sourceforge.net \
--cc=froese@gmx.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox