From: Alexey Fisher <bug-track@fisher-privat.net>
To: Takashi Iwai <tiwai@suse.de>
Cc: alsa-devel@alsa-project.org
Subject: Re: line-in on Intel DG45ID
Date: Wed, 02 Dec 2009 11:30:50 +0100 [thread overview]
Message-ID: <1259749850.3195.22.camel@mini> (raw)
In-Reply-To: <s5h638qzobx.wl%tiwai@suse.de>
Am Dienstag, den 01.12.2009, 16:49 +0100 schrieb Takashi Iwai:
> At Tue, 01 Dec 2009 16:45:35 +0100,
> Alexey Fisher wrote:
> >
> > Am Dienstag, den 01.12.2009, 16:03 +0100 schrieb Takashi Iwai:
> > > At Mon, 30 Nov 2009 09:06:40 +0100,
> > > Alexey Fisher wrote:
> > > >
> > > > Hi,
> > > > i recently tried to digitalise some tapes and found line-in not enabled
> > > > on my board (Intel DG45ID). (Codec: IDT 92HD73E1X5)
> > > > >From the board documentation i know blue jack used for line-in or side
> > > > surround. Even i use normal stereo i can't enable line-in.
> > > >
> > > > So my question, is it really to make a switch between surround and
> > > > stereo with line-in? I know it should be possible. Or to have this
> > > > switch for mic input?
> > >
> > > Which ALSA driver version are you using?
> > >
> > > The very latest one should have a "Line Jack Mode", with which you
> > > can change the input/output via enum control.
> >
> > i use recent alsa-kernel.git, i found this switch.
>
> Check sound GIT tree, to be sure:
> git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git
>
> A snapshot tarball for external builds is:
> ftp://ftp.kernel.org/pub/linux/kernel/people/tiwai/snapshot/alsa-driver-snapshot.tar.gz
>
> > Currently i trying to
> > dig deeper in the code. Seems like this board is not really supported...
> > for normal tasks like stereo in / stereo out - is ok, but surround seems
> > to be messed up, mixer map too.
> > For example: "speaker-test -c 6" will produce "Front L/R" on all jacks.
>
> You have to pass -Dsurround51, too.
Tank you for the tip, speaker-test worked for my Hercules so i thout
should work for intel too. So with tiwai.git and -Dsurround51 or
surrounf71 outputs are working. Bad the mixer map is in really bad
state. Here is my current investigation, here are the controls i tested:
[jack] [surround]; [mixers;...]
green - front r/l;Master; PCM; Speeker 0;
blue - side r/l ------- PCM; Speaker 3;
black - rear r/l; Master; PCM; Speaker 1;
orange - cenrat f/r; Master; PCM; ------; swap;
('Swap Center/LFE Playback Switch' (change front and reare outputs))
You can see - master control not all jacks and most (not all) jacks have
own mixer.
'Master Playback Switch' <- master but not for all (blue jack not
contr)
'Master Playback Volume' <- master but not for all (blue jack not contr)
'PCM Playback Volume' <- bad sound if too lo
'Center Playback Switch' <- not working?
'Center Playback Volume' <- not working?
'LFE Playback Switch' <- not working?
'LFE Playback Volume' <- not working ?
'Speaker Playback Switch' <- Front Playback
'Speaker Playback Switch',inx=1 <- Rear Playback
'Speaker Playback Switch',inx=3 <- Side Playback
'Speaker Playback Volume' <- Front Playback
'Speaker Playback Volume',inx=1 <- Rear Playback
'Speaker Playback Volume',inx=3 <- Side Playback
'Swap Center/LFE Playback Switch'<- order switch ?or route?
I will continue to investigate this board.
next prev parent reply other threads:[~2009-12-02 10:30 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-11-30 8:06 line-in on Intel DG45ID Alexey Fisher
2009-12-01 15:03 ` Takashi Iwai
2009-12-01 15:45 ` Alexey Fisher
2009-12-01 15:49 ` Takashi Iwai
2009-12-02 10:30 ` Alexey Fisher [this message]
2009-12-05 22:14 ` Alexey Fisher
2009-12-06 3:47 ` Paulo Cavalcanti
2009-12-06 10:01 ` Alexey Fisher
2009-12-06 10:14 ` [PATCH] Introduce config for intel dg45id board Alexey Fisher
2009-12-06 10:29 ` [PATCH v2] " Alexey Fisher
2009-12-08 11:04 ` Takashi Iwai
2009-12-08 13:02 ` Alexey Fisher
2009-12-08 13:15 ` Takashi Iwai
[not found] ` <1260289818.5210.59.camel@mini>
2009-12-08 16:39 ` Takashi Iwai
2009-12-08 20:12 ` Alexey Fisher
2009-12-08 20:38 ` Takashi Iwai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1259749850.3195.22.camel@mini \
--to=bug-track@fisher-privat.net \
--cc=alsa-devel@alsa-project.org \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox