* [PATCH v6 1/9] davinci: EMAC support for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-10-29 15:10 ` [PATCH v6 2/9] davinci: EDMA " vm.rod25
` (7 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch adds EMAC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
arch/arm/mach-davinci/board-omapl138-hawk.c | 43 +++++++++++++++++++++++++++
1 files changed, 43 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index c472dd8..62d35f0 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -19,6 +19,47 @@
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
+#include <mach/mux.h>
+
+#define HAWKBOARD_PHY_ID "0:07"
+
+static short omapl138_hawk_mii_pins[] __initdata = {
+ DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
+ DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
+ DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
+ DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
+ DA850_MDIO_D,
+ -1
+};
+
+static __init void omapl138_hawk_config_emac(void)
+{
+ void __iomem *cfgchip3 = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
+ int ret;
+ u32 val;
+ struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+ val = __raw_readl(cfgchip3);
+ val &= ~BIT(8);
+ ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins);
+ if (ret) {
+ pr_warning("%s: cpgmac/mii mux setup failed: %d\n",
+ __func__, ret);
+ return;
+ }
+
+ /* configure the CFGCHIP3 register for MII */
+ __raw_writel(val, cfgchip3);
+ pr_info("EMAC: MII PHY configured\n");
+
+ soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID;
+
+ ret = da8xx_register_emac();
+ if (ret)
+ pr_warning("%s: emac registration failed: %d\n",
+ __func__, ret);
+}
+
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
@@ -30,6 +71,8 @@ static __init void omapl138_hawk_init(void)
davinci_serial_init(&omapl138_hawk_uart_config);
+ omapl138_hawk_config_emac();
+
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v6 2/9] davinci: EDMA support for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
2010-10-29 15:10 ` [PATCH v6 1/9] davinci: EMAC support for Omapl138-Hawkboard vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-10-29 15:10 ` [PATCH v6 3/9] davinci: ASoC " vm.rod25
` (6 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch adds EDMA support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
arch/arm/mach-davinci/board-omapl138-hawk.c | 54 +++++++++++++++++++++++++++
1 files changed, 54 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 62d35f0..114fc9b 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -60,6 +60,55 @@ static __init void omapl138_hawk_config_emac(void)
__func__, ret);
}
+/*
+ * The following EDMA channels/slots are not being used by drivers (for
+ * example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM/Hawkboard,
+ * hence they are being reserved for codecs on the DSP side.
+ */
+static const s16 da850_dma0_rsv_chans[][2] = {
+ /* (offset, number) */
+ { 8, 6},
+ {24, 4},
+ {30, 2},
+ {-1, -1}
+};
+
+static const s16 da850_dma0_rsv_slots[][2] = {
+ /* (offset, number) */
+ { 8, 6},
+ {24, 4},
+ {30, 50},
+ {-1, -1}
+};
+
+static const s16 da850_dma1_rsv_chans[][2] = {
+ /* (offset, number) */
+ { 0, 28},
+ {30, 2},
+ {-1, -1}
+};
+
+static const s16 da850_dma1_rsv_slots[][2] = {
+ /* (offset, number) */
+ { 0, 28},
+ {30, 90},
+ {-1, -1}
+};
+
+static struct edma_rsv_info da850_edma_cc0_rsv = {
+ .rsv_chans = da850_dma0_rsv_chans,
+ .rsv_slots = da850_dma0_rsv_slots,
+};
+
+static struct edma_rsv_info da850_edma_cc1_rsv = {
+ .rsv_chans = da850_dma1_rsv_chans,
+ .rsv_slots = da850_dma1_rsv_slots,
+};
+
+static struct edma_rsv_info *da850_edma_rsv[2] = {
+ &da850_edma_cc0_rsv,
+ &da850_edma_cc1_rsv,
+};
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
@@ -73,6 +122,11 @@ static __init void omapl138_hawk_init(void)
omapl138_hawk_config_emac();
+ ret = da850_register_edma(da850_edma_rsv);
+ if (ret)
+ pr_warning("%s: EDMA registration failed: %d\n",
+ __func__, ret);
+
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v6 3/9] davinci: ASoC support for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
2010-10-29 15:10 ` [PATCH v6 1/9] davinci: EMAC support for Omapl138-Hawkboard vm.rod25
2010-10-29 15:10 ` [PATCH v6 2/9] davinci: EDMA " vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-11-01 13:23 ` Mark Brown
2010-10-29 15:10 ` [PATCH v6 4/9] davinci: McASP configuration " vm.rod25
` (5 subsequent siblings)
8 siblings, 1 reply; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch adds ASoC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
sound/soc/davinci/Kconfig | 5 +++--
sound/soc/davinci/davinci-evm.c | 6 ++++--
2 files changed, 7 insertions(+), 4 deletions(-)
diff --git a/sound/soc/davinci/Kconfig b/sound/soc/davinci/Kconfig
index 6bbf001..72c6752 100644
--- a/sound/soc/davinci/Kconfig
+++ b/sound/soc/davinci/Kconfig
@@ -76,8 +76,9 @@ config SND_DA830_SOC_EVM
DA830/OMAP-L137 EVM
config SND_DA850_SOC_EVM
- tristate "SoC Audio support for DA850/OMAP-L138 EVM"
- depends on SND_DAVINCI_SOC && MACH_DAVINCI_DA850_EVM
+ tristate "SoC Audio support for DA850/OMAP-L138 EVM/Hawkboard"
+ depends on SND_DAVINCI_SOC && (MACH_DAVINCI_DA850_EVM || \
+ MACH_OMAPL138_HAWKBOARD)
select SND_DAVINCI_SOC_MCASP
select SND_SOC_TLV320AIC3X
help
diff --git a/sound/soc/davinci/davinci-evm.c b/sound/soc/davinci/davinci-evm.c
index 97f74d6..73093eb 100644
--- a/sound/soc/davinci/davinci-evm.c
+++ b/sound/soc/davinci/davinci-evm.c
@@ -59,7 +59,8 @@ static int evm_hw_params(struct snd_pcm_substream *substream,
sysclk = 12288000;
else if (machine_is_davinci_da830_evm() ||
- machine_is_davinci_da850_evm())
+ machine_is_davinci_da850_evm() ||
+ machine_is_omapl138_hawkboard())
sysclk = 24576000;
else
@@ -311,7 +312,8 @@ static int __init evm_init(void)
} else if (machine_is_davinci_da830_evm()) {
evm_snd_dev_data = &da830_evm_snd_devdata;
index = 1;
- } else if (machine_is_davinci_da850_evm()) {
+ } else if (machine_is_davinci_da850_evm() ||
+ machine_is_omapl138_hawkboard()) {
evm_snd_dev_data = &da850_evm_snd_devdata;
index = 0;
} else
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v6 3/9] davinci: ASoC support for Omapl138-Hawkboard
2010-10-29 15:10 ` [PATCH v6 3/9] davinci: ASoC " vm.rod25
@ 2010-11-01 13:23 ` Mark Brown
0 siblings, 0 replies; 14+ messages in thread
From: Mark Brown @ 2010-11-01 13:23 UTC (permalink / raw)
To: vm.rod25
Cc: davinci-linux-open-source, sshtylyov, khilman, nsekhar,
alsa-devel, khasim, caglarakyuz, lrg
On Fri, Oct 29, 2010 at 10:10:39AM -0500, vm.rod25@gmail.com wrote:
> From: Victor Rodriguez <victor.rodriguez@sasken.com>
>
> This patch adds ASoC support for the Hawkboard-L138 system
>
> Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v6 4/9] davinci: McASP configuration for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
` (2 preceding siblings ...)
2010-10-29 15:10 ` [PATCH v6 3/9] davinci: ASoC " vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-10-29 15:10 ` [PATCH v6 5/9] davinci: Audio support " vm.rod25
` (4 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch defines Pin Mux configuration for MacASP
used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
arch/arm/mach-davinci/da850.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 63916b9..f033a0a 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {
const short da850_mcasp_pins[] __initdata = {
DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
- DA850_AXR_11, DA850_AXR_12,
+ DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,
-1
};
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v6 5/9] davinci: Audio support for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
` (3 preceding siblings ...)
2010-10-29 15:10 ` [PATCH v6 4/9] davinci: McASP configuration " vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-10-29 15:10 ` [PATCH v6 6/9] davinci: MMC/SD and USB-OHCI configuration " vm.rod25
` (3 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch adds sound support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
Notes:
This patch works with da8xx_omapl_defconfig
In order to test ALSA utils select in menuconfig like insmodule:
Sound card support --->
Advanced Linux Sound Architecture --->
ALSA for SoC audio support --->
SoC Audio for the TI DAVINCI chip
SoC Audio support for DA850/OMAP-L138 EVM/Hawkboard
arch/arm/mach-davinci/board-omapl138-hawk.c | 46 +++++++++++++++++++++++++++
1 files changed, 46 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 114fc9b..115dac0 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -13,6 +13,7 @@
#include <linux/init.h>
#include <linux/console.h>
#include <linux/gpio.h>
+#include <linux/i2c.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -110,6 +111,38 @@ static struct edma_rsv_info *da850_edma_rsv[2] = {
&da850_edma_cc1_rsv,
};
+static struct i2c_board_info __initdata omapl138_hawk_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("tlv320aic3x", 0x18),
+ },
+};
+
+static struct davinci_i2c_platform_data omapl138_hawk_i2c_0_pdata = {
+ .bus_freq = 100, /* kHz */
+ .bus_delay = 0, /* usec */
+};
+
+/* davinci Hawkboard audio machine driver */
+static u8 da850_iis_serializer_direction[] = {
+ INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
+ INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
+ INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
+ INACTIVE_MODE, TX_MODE, RX_MODE, INACTIVE_MODE,
+};
+
+static struct snd_platform_data omapl138_hawk_snd_data = {
+ .tx_dma_offset = 0x2000,
+ .rx_dma_offset = 0x2000,
+ .op_mode = DAVINCI_MCASP_IIS_MODE,
+ .num_serializer = ARRAY_SIZE(da850_iis_serializer_direction),
+ .tdm_slots = 2,
+ .serial_dir = da850_iis_serializer_direction,
+ .asp_chan_q = EVENTQ_1,
+ .version = MCASP_VERSION_2,
+ .txnumevt = 1,
+ .rxnumevt = 1,
+};
+
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
};
@@ -127,6 +160,19 @@ static __init void omapl138_hawk_init(void)
pr_warning("%s: EDMA registration failed: %d\n",
__func__, ret);
+ i2c_register_board_info(1, omapl138_hawk_i2c_devices,
+ ARRAY_SIZE(omapl138_hawk_i2c_devices));
+
+ ret = da8xx_register_i2c(0, &omapl138_hawk_i2c_0_pdata);
+ if (ret)
+ pr_warning("%s: i2c0 registration failed: %d\n",
+ __func__, ret);
+
+ ret = davinci_cfg_reg_list(da850_mcasp_pins);
+ if (ret)
+ pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);
+ da8xx_register_mcasp(0, &omapl138_hawk_snd_data);
+
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v6 6/9] davinci: MMC/SD and USB-OHCI configuration for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
` (4 preceding siblings ...)
2010-10-29 15:10 ` [PATCH v6 5/9] davinci: Audio support " vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-10-29 15:10 ` [PATCH v6 7/9] davinci: MMC/SD support for Omapl138-Hawkboar vm.rod25
` (2 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch defines Pin Mux configuration to enable MMC/SD
and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
arch/arm/mach-davinci/da850.c | 4 ++++
arch/arm/mach-davinci/include/mach/mux.h | 4 ++++
2 files changed, 8 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index f033a0a..4458bff 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -543,11 +543,15 @@ static const struct mux_config da850_pins[] = {
MUX_CFG(DA850, EMA_WAIT_1, 6, 24, 15, 1, false)
MUX_CFG(DA850, NEMA_CS_2, 7, 0, 15, 1, false)
/* GPIO function */
+ MUX_CFG(DA850, GPIO2_4, 6, 12, 15, 8, false)
MUX_CFG(DA850, GPIO2_6, 6, 4, 15, 8, false)
MUX_CFG(DA850, GPIO2_8, 5, 28, 15, 8, false)
MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false)
+ MUX_CFG(DA850, GPIO3_12, 7, 12, 15, 8, false)
+ MUX_CFG(DA850, GPIO3_13, 7, 8, 15, 8, false)
MUX_CFG(DA850, GPIO4_0, 10, 28, 15, 8, false)
MUX_CFG(DA850, GPIO4_1, 10, 24, 15, 8, false)
+ MUX_CFG(DA850, GPIO6_13, 13, 8, 15, 8, false)
MUX_CFG(DA850, RTC_ALARM, 0, 28, 15, 2, false)
#endif
};
diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h
index de11aac..5d4e0fe 100644
--- a/arch/arm/mach-davinci/include/mach/mux.h
+++ b/arch/arm/mach-davinci/include/mach/mux.h
@@ -908,11 +908,15 @@ enum davinci_da850_index {
DA850_NEMA_CS_2,
/* GPIO function */
+ DA850_GPIO2_4,
DA850_GPIO2_6,
DA850_GPIO2_8,
DA850_GPIO2_15,
+ DA850_GPIO3_12,
+ DA850_GPIO3_13,
DA850_GPIO4_0,
DA850_GPIO4_1,
+ DA850_GPIO6_13,
DA850_RTC_ALARM,
};
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v6 7/9] davinci: MMC/SD support for Omapl138-Hawkboar
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
` (5 preceding siblings ...)
2010-10-29 15:10 ` [PATCH v6 6/9] davinci: MMC/SD and USB-OHCI configuration " vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
2010-10-29 15:10 ` [PATCH v6 8/9] davinci: USB clocks for Omapl138-Hawkboard vm.rod25
[not found] ` <1288365045-2709-1-git-send-email-vm.rod25-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch adds MMC/SD support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
Notes:
This patch works with da8xx_omapl_defconfig
In order to test it select in menuconfig like insmodule
MMC/SD/SDIO card support --->
MMC block device driver
Use bounce buffer for simple hosts
TI DAVINCI Multimedia Card Interface support
arch/arm/mach-davinci/board-omapl138-hawk.c | 63 +++++++++++++++++++++++++++
1 files changed, 63 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 115dac0..02e54fa 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -23,6 +23,8 @@
#include <mach/mux.h>
#define HAWKBOARD_PHY_ID "0:07"
+#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12)
+#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13)
static short omapl138_hawk_mii_pins[] __initdata = {
DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
@@ -143,6 +145,65 @@ static struct snd_platform_data omapl138_hawk_snd_data = {
.rxnumevt = 1,
};
+static const short hawk_mmcsd0_pins[] = {
+ DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2,
+ DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD,
+ DA850_GPIO3_12, DA850_GPIO3_13,
+ -1
+};
+
+static int da850_hawk_mmc_get_ro(int index)
+{
+ return gpio_get_value(DA850_HAWK_MMCSD_WP_PIN);
+}
+
+static int da850_hawk_mmc_get_cd(int index)
+{
+ return !gpio_get_value(DA850_HAWK_MMCSD_CD_PIN);
+}
+
+static struct davinci_mmc_config da850_mmc_config = {
+ .get_ro = da850_hawk_mmc_get_ro,
+ .get_cd = da850_hawk_mmc_get_cd,
+ .wires = 4,
+ .max_freq = 50000000,
+ .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
+ .version = MMC_CTLR_VERSION_2,
+};
+
+static __init void omapl138_hawk_mmc_init(void)
+{
+ int ret;
+
+ ret = davinci_cfg_reg_list(hawk_mmcsd0_pins);
+ if (ret) {
+ pr_warning("%s: MMC/SD0 mux setup failed: %d\n",
+ __func__, ret);
+ return;
+ }
+
+ ret = gpio_request_one(DA850_HAWK_MMCSD_CD_PIN,
+ GPIOF_DIR_IN, "MMC CD");
+ if (ret < 0) {
+ pr_warning("%s: can not open GPIO %d\n",
+ __func__, DA850_HAWK_MMCSD_CD_PIN);
+ return;
+ }
+
+ ret = gpio_request_one(DA850_HAWK_MMCSD_WP_PIN,
+ GPIOF_DIR_IN, "MMC WP");
+ if (ret < 0) {
+ pr_warning("%s: can not open GPIO %d\n",
+ __func__, DA850_HAWK_MMCSD_WP_PIN);
+ return;
+ }
+
+ ret = da8xx_register_mmcsd0(&da850_mmc_config);
+ if (ret)
+ pr_warning("%s: MMC/SD0 registration failed: %d\n",
+ __func__, ret);
+}
+
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
};
@@ -173,6 +234,8 @@ static __init void omapl138_hawk_init(void)
pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);
da8xx_register_mcasp(0, &omapl138_hawk_snd_data);
+ omapl138_hawk_mmc_init();
+
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v6 8/9] davinci: USB clocks for Omapl138-Hawkboard
2010-10-29 15:10 [PATCH v6 0/9] Add Omapl138-Hawkboard support vm.rod25
` (6 preceding siblings ...)
2010-10-29 15:10 ` [PATCH v6 7/9] davinci: MMC/SD support for Omapl138-Hawkboar vm.rod25
@ 2010-10-29 15:10 ` vm.rod25
[not found] ` <1288365045-2709-1-git-send-email-vm.rod25-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
8 siblings, 0 replies; 14+ messages in thread
From: vm.rod25 @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source
Cc: alsa-devel, sshtylyov, khilman, broonie, nsekhar, khasim,
caglarakyuz, lrg
From: Victor Rodriguez <victor.rodriguez@sasken.com>
This patch adds USB1.1 and USB2.0 clocks for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
---
arch/arm/mach-davinci/da850.c | 16 ++++++++++++++++
1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 4458bff..b3b1adb 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -345,6 +345,20 @@ static struct clk aemif_clk = {
.flags = ALWAYS_ENABLED,
};
+static struct clk usb11_clk = {
+ .name = "usb11",
+ .parent = &pll0_sysclk4,
+ .lpsc = DA8XX_LPSC1_USB11,
+ .gpsc = 1,
+};
+
+static struct clk usb20_clk = {
+ .name = "usb20",
+ .parent = &pll0_sysclk2,
+ .lpsc = DA8XX_LPSC1_USB20,
+ .gpsc = 1,
+};
+
static struct clk_lookup da850_clks[] = {
CLK(NULL, "ref", &ref_clk),
CLK(NULL, "pll0", &pll0_clk),
@@ -387,6 +401,8 @@ static struct clk_lookup da850_clks[] = {
CLK("davinci_mmc.0", NULL, &mmcsd0_clk),
CLK("davinci_mmc.1", NULL, &mmcsd1_clk),
CLK(NULL, "aemif", &aemif_clk),
+ CLK(NULL, "usb11", &usb11_clk),
+ CLK(NULL, "usb20", &usb20_clk),
CLK(NULL, NULL, NULL),
};
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread[parent not found: <1288365045-2709-1-git-send-email-vm.rod25-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]
* [PATCH v6 9/9] davinci: USB1.1 support for Omapl138-Hawkboard
[not found] ` <1288365045-2709-1-git-send-email-vm.rod25-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
@ 2010-10-29 15:10 ` vm.rod25-Re5JQEeQqe8AvxtiuMwx3w
[not found] ` <1288365045-2709-10-git-send-email-vm.rod25-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
0 siblings, 1 reply; 14+ messages in thread
From: vm.rod25-Re5JQEeQqe8AvxtiuMwx3w @ 2010-10-29 15:10 UTC (permalink / raw)
To: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/
Cc: alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
sshtylyov-Igf4POYTYCDQT0dZR+AlfA,
broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E,
lrg-kDsPt+C1G03kYMGBc/C6ZA
From: Victor Rodriguez <victor.rodriguez-Ut8ZLSGP1ULQT0dZR+AlfA@public.gmane.org>
This patch adds USB1.1 support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <victor.rodriguez-Ut8ZLSGP1ULQT0dZR+AlfA@public.gmane.org>
---
Notes:
This patch works with da8xx_omapl_defconfig
In order to test it select in menuconfig like insmodule
Device Drivers --->
SCSI device support --->
SCSI device support
legacy /proc/scsi/ support
SCSI disk support
SCSI low-level drivers
USB support --->
Support for Host-side US
OHCI HCD support (NEW)
USB Mass Storage support (NEW)
USB Gadget Support --->
USB Gadget Drivers (Ethernet Gadget\
(with CDC Ethernet support)) --->
NOP USB Transceiver Driver
And you will be able to mount and USB pen drive
In order to connect a keyboard or a mouse on a USB-hub
select in menuconfig like insmodule
HID Devices --->
Generic HID support
USB Human Interface Device (full HID) support
arch/arm/mach-davinci/board-omapl138-hawk.c | 107 +++++++++++++++++++++++++++
1 files changed, 107 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 02e54fa..5c8202b 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -26,6 +26,9 @@
#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12)
#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13)
+#define DA850_USB1_VBUS_PIN GPIO_TO_PIN(2, 4)
+#define DA850_USB1_OC_PIN GPIO_TO_PIN(6, 13)
+
static short omapl138_hawk_mii_pins[] __initdata = {
DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
@@ -204,6 +207,108 @@ static __init void omapl138_hawk_mmc_init(void)
__func__, ret);
}
+static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id);
+static da8xx_ocic_handler_t hawk_usb_ocic_handler;
+
+static const short da850_hawk_usb11_pins[] = {
+ DA850_GPIO2_4, DA850_GPIO6_13,
+ -1
+};
+
+static int hawk_usb_set_power(unsigned port, int on)
+{
+ gpio_set_value(DA850_USB1_VBUS_PIN, on);
+ return 0;
+}
+
+static int hawk_usb_get_power(unsigned port)
+{
+ return gpio_get_value(DA850_USB1_VBUS_PIN);
+}
+
+static int hawk_usb_get_oci(unsigned port)
+{
+ return !gpio_get_value(DA850_USB1_OC_PIN);
+}
+
+static int hawk_usb_ocic_notify(da8xx_ocic_handler_t handler)
+{
+ int irq = gpio_to_irq(DA850_USB1_OC_PIN);
+ int error = 0;
+
+ if (handler != NULL) {
+ hawk_usb_ocic_handler = handler;
+
+ error = request_irq(irq, omapl138_hawk_usb_ocic_irq,
+ IRQF_DISABLED | IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING,
+ "OHCI over-current indicator", NULL);
+ if (error)
+ pr_err(KERN_ERR "%s: could not request IRQ to watch "
+ "over-current indicator changes\n", __func__);
+ } else
+ free_irq(irq, NULL);
+
+ return error;
+}
+
+static struct da8xx_ohci_root_hub omapl138_hawk_usb11_pdata = {
+ .set_power = hawk_usb_set_power,
+ .get_power = hawk_usb_get_power,
+ .get_oci = hawk_usb_get_oci,
+ .ocic_notify = hawk_usb_ocic_notify,
+ /* TPS2087 switch @ 5V */
+ .potpgt = (3 + 1) / 2, /* 3 ms max */
+};
+
+static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
+{
+ hawk_usb_ocic_handler(&omapl138_hawk_usb11_pdata, 1);
+ return IRQ_HANDLED;
+}
+
+static __init void omapl138_hawk_usb_init(void)
+{
+ int ret;
+ u32 cfgchip2;
+
+ ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
+ if (ret) {
+ pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
+ __func__, ret);
+ return;
+ }
+
+ /*
+ * Setup the Ref. clock frequency for the HAWK at 24 MHz.
+ */
+ cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+ cfgchip2 &= ~CFGCHIP2_REFFREQ;
+ cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ;
+ __raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ ret = gpio_request_one(DA850_USB1_VBUS_PIN,
+ GPIOF_DIR_OUT, "USB1 VBUS");
+ if (ret < 0) {
+ pr_err(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
+ "power control: %d\n", __func__, ret);
+ return;
+ }
+
+ ret = gpio_request_one(DA850_USB1_OC_PIN,
+ GPIOF_DIR_IN, "USB1 OC");
+ if (ret < 0) {
+ pr_err(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
+ "over-current indicator: %d\n", __func__, ret);
+ return;
+ }
+
+ ret = da8xx_register_usb11(&omapl138_hawk_usb11_pdata);
+ if (ret)
+ pr_warning("%s: USB 1.1 registration failed: %d\n",
+ __func__, ret);
+}
+
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
};
@@ -236,6 +341,8 @@ static __init void omapl138_hawk_init(void)
omapl138_hawk_mmc_init();
+ omapl138_hawk_usb_init();
+
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread