From: Lars-Peter Clausen <lars@metafoo.de>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>,
Liam Girdwood <lrg@slimlogic.co.uk>,
Mike Frysinger <vapier@gentoo.org>
Cc: device-driver-devel@blackfin.uclinux.org,
uclinux-dist-devel@blackfin.uclinux.org,
alsa-devel@alsa-project.org, Lars-Peter Clausen <lars@metafoo.de>
Subject: [PATCH 1/4] Blackfin: Use 8bit spi transfers for the ad1836
Date: Thu, 5 May 2011 19:52:43 +0200 [thread overview]
Message-ID: <1304617966-4410-1-git-send-email-lars@metafoo.de> (raw)
Currently there is a special case for the ad1836 in the ASoC generic spi write
functions, which swaps the upper and the lower byte for 4/12 transfers.
This was done, because the 4/12 spi write function was added for the ad1836
for which all of the users are configured to use use 16-bit transfers.
In order to be able to get rid of this special casing switch all users of
ad1836 to 8-bit transfers.
Since 8-bit, no-dma transfers is the default configuration we can remove the
bfin5xx_spi_chip struct for the ad1836 altogether.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
---
arch/blackfin/mach-bf527/boards/ad7160eval.c | 9 ---------
arch/blackfin/mach-bf527/boards/cm_bf527.c | 9 ---------
arch/blackfin/mach-bf527/boards/ezkit.c | 9 ---------
arch/blackfin/mach-bf533/boards/H8606.c | 8 --------
arch/blackfin/mach-bf533/boards/cm_bf533.c | 8 --------
arch/blackfin/mach-bf533/boards/ezkit.c | 8 --------
arch/blackfin/mach-bf533/boards/stamp.c | 8 --------
arch/blackfin/mach-bf537/boards/cm_bf537e.c | 8 --------
arch/blackfin/mach-bf537/boards/cm_bf537u.c | 8 --------
arch/blackfin/mach-bf537/boards/pnav10.c | 9 ---------
arch/blackfin/mach-bf537/boards/stamp.c | 9 ---------
arch/blackfin/mach-bf537/boards/tcm_bf537.c | 8 --------
arch/blackfin/mach-bf548/boards/ezkit.c | 9 ---------
arch/blackfin/mach-bf561/boards/cm_bf561.c | 8 --------
arch/blackfin/mach-bf561/boards/ezkit.c | 9 ---------
15 files changed, 0 insertions(+), 127 deletions(-)
diff --git a/arch/blackfin/mach-bf527/boards/ad7160eval.c b/arch/blackfin/mach-bf527/boards/ad7160eval.c
index ccab4c6..eb712ce 100644
--- a/arch/blackfin/mach-bf527/boards/ad7160eval.c
+++ b/arch/blackfin/mach-bf527/boards/ad7160eval.c
@@ -269,14 +269,6 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -328,7 +320,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index c9d6dc8..ccdf2e7 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -367,14 +367,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -452,7 +444,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 2cd2ff6..503837b 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -460,14 +460,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -583,7 +575,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index d4bfcea..41c9329 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -171,13 +171,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
@@ -212,7 +205,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 16,
.bus_num = 1,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index 4d5604e..2506703 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -71,13 +71,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -116,7 +109,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index b67b91d..7d82463 100644
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -222,13 +222,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
@@ -267,7 +260,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 43224ef..32091b8 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -184,13 +184,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
@@ -258,7 +251,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
- .controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537e.c b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
index d582b81..cb0a34e 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537e.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
@@ -73,13 +73,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -118,7 +111,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537u.c b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
index cbb8098..197a77c 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537u.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
@@ -74,13 +74,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -119,7 +112,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 9389f03..7037128 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -197,14 +197,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -267,7 +259,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 3fa3354..343f969 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -549,14 +549,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_SND_BF5XX_SOC_AD193X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
@@ -1076,7 +1068,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
- .controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 164a7e0..b720fec 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -74,13 +74,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -119,7 +112,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index 93e19a5..002e0f9 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -1013,14 +1013,6 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
@@ -1077,7 +1069,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 1,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 87595cd..1418053 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -72,13 +72,6 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
@@ -117,7 +110,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
- .controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index f667e77..9f58605 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -275,14 +275,6 @@ static struct platform_device ezkit_flash_device = {
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
@@ -337,7 +329,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
- .controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
--
1.7.2.5
next reply other threads:[~2011-05-05 17:53 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-05 17:52 Lars-Peter Clausen [this message]
2011-05-05 17:52 ` [PATCH 2/4] ASoC: Do not swap upper and lower byte in snd_soc_4_12_spi_write Lars-Peter Clausen
2011-05-05 17:52 ` [PATCH 3/4] ASoC: Get rid of snd_soc_*_*_spi_write wrapper functions Lars-Peter Clausen
2011-05-12 12:25 ` Barry Song
2011-05-05 17:52 ` [PATCH 4/4] ASoC: Use spi_write in do_spi_write Lars-Peter Clausen
2011-05-05 22:56 ` [uclinux-dist-devel] [PATCH 1/4] Blackfin: Use 8bit spi transfers for the ad1836 Mike Frysinger
2011-05-06 12:28 ` Lars-Peter Clausen
2011-05-06 12:48 ` Mark Brown
2011-05-06 13:12 ` [Device-drivers-devel] " Mike Frysinger
2011-05-06 13:19 ` Lars-Peter Clausen
2011-05-06 13:26 ` Mark Brown
2011-05-06 13:31 ` Lars-Peter Clausen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1304617966-4410-1-git-send-email-lars@metafoo.de \
--to=lars@metafoo.de \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=device-driver-devel@blackfin.uclinux.org \
--cc=lrg@slimlogic.co.uk \
--cc=uclinux-dist-devel@blackfin.uclinux.org \
--cc=vapier@gentoo.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).