From: Mark Brown <broonie@opensource.wolfsonmicro.com>
To: Samuel Ortiz <sameo@linux.intel.com>, Liam Girdwood <lrg@ti.com>
Cc: alsa-devel@alsa-project.org, patches@opensource.wolfsonmicro.com,
linux-kernel@vger.kernel.org,
Mark Brown <broonie@opensource.wolfsonmicro.com>
Subject: [PATCH 2/3] mfd/ASoC: Convert WM8994 driver to use regmap patches
Date: Mon, 23 Jan 2012 13:59:31 +0000 [thread overview]
Message-ID: <1327327172-8411-2-git-send-email-broonie@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1327327172-8411-1-git-send-email-broonie@opensource.wolfsonmicro.com>
Early revisions of several of the WM8994 variants have register updates
to improve performance. Move these over to using the regmap patch system
instead of open coding them in the audio driver. Since the regmap init
is done by the MFD the code is moved there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
If possible I'd like to merge this via regmap as the regmap patch
support is new and won't be in mainline until 3.4. Is that OK Samuel?
drivers/mfd/wm8994-core.c | 61 ++++++++++++++++++++++++++++++++++++++++++++-
sound/soc/codecs/wm8994.c | 25 +-----------------
2 files changed, 61 insertions(+), 25 deletions(-)
diff --git a/drivers/mfd/wm8994-core.c b/drivers/mfd/wm8994-core.c
index a215b15..f275427 100644
--- a/drivers/mfd/wm8994-core.c
+++ b/drivers/mfd/wm8994-core.c
@@ -359,6 +359,27 @@ static int wm8994_ldo_in_use(struct wm8994_pdata *pdata, int ldo)
}
#endif
+static const __devinitdata struct reg_default wm8994_revc_patch[] = {
+ { 0x102, 0x3 },
+ { 0x56, 0x3 },
+ { 0x817, 0x0 },
+ { 0x102, 0x0 },
+};
+
+static const __devinitdata struct reg_default wm8958_reva_patch[] = {
+ { 0x102, 0x3 },
+ { 0xcb, 0x81 },
+ { 0x817, 0x0 },
+ { 0x102, 0x0 },
+};
+
+static const __devinitdata struct reg_default wm1811_reva_patch[] = {
+ { 0x102, 0x3 },
+ { 0x5d, 0x7e },
+ { 0x5e, 0x0 },
+ { 0x102, 0x0 },
+};
+
/*
* Instantiate the generic non-control parts of the device.
*/
@@ -366,8 +387,9 @@ static __devinit int wm8994_device_init(struct wm8994 *wm8994, int irq)
{
struct wm8994_pdata *pdata = wm8994->dev->platform_data;
struct regmap_config *regmap_config;
+ const struct reg_default *regmap_patch = NULL;
const char *devname;
- int ret, i;
+ int ret, i, patch_regs;
int pulls = 0;
dev_set_drvdata(wm8994->dev, wm8994);
@@ -488,15 +510,42 @@ static __devinit int wm8994_device_init(struct wm8994 *wm8994, int irq)
"revision %c not fully supported\n",
'A' + wm8994->revision);
break;
+ case 2:
+ case 3:
+ regmap_patch = wm8994_revc_patch;
+ patch_regs = ARRAY_SIZE(wm8994_revc_patch);
+ break;
+ default:
+ break;
+ }
+ break;
+
+ case WM8958:
+ switch (wm8994->revision) {
+ case 0:
+ regmap_patch = wm8958_reva_patch;
+ patch_regs = ARRAY_SIZE(wm8958_reva_patch);
+ break;
default:
break;
}
break;
+
case WM1811:
/* Revision C did not change the relevant layer */
if (wm8994->revision > 1)
wm8994->revision++;
+ switch (wm8994->revision) {
+ case 0:
+ case 1:
+ regmap_patch = wm1811_reva_patch;
+ patch_regs = ARRAY_SIZE(wm1811_reva_patch);
+ break;
+ default:
+ break;
+ }
break;
+
default:
break;
}
@@ -526,6 +575,16 @@ static __devinit int wm8994_device_init(struct wm8994 *wm8994, int irq)
return ret;
}
+ if (regmap_patch) {
+ ret = regmap_register_patch(wm8994->regmap, regmap_patch,
+ patch_regs);
+ if (ret != 0) {
+ dev_err(wm8994->dev, "Failed to register patch: %d\n",
+ ret);
+ goto err_regmap;
+ }
+ }
+
if (pdata) {
wm8994->irq_base = pdata->irq_base;
wm8994->gpio_base = pdata->gpio_base;
diff --git a/sound/soc/codecs/wm8994.c b/sound/soc/codecs/wm8994.c
index b047bfa..143f1c4 100644
--- a/sound/soc/codecs/wm8994.c
+++ b/sound/soc/codecs/wm8994.c
@@ -2090,26 +2090,9 @@ static int wm8994_set_bias_level(struct snd_soc_codec *codec,
case SND_SOC_BIAS_STANDBY:
if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) {
switch (control->type) {
- case WM8994:
- if (wm8994->revision < 4) {
- /* Tweak DC servo and DSP
- * configuration for improved
- * performance. */
- snd_soc_write(codec, 0x102, 0x3);
- snd_soc_write(codec, 0x56, 0x3);
- snd_soc_write(codec, 0x817, 0);
- snd_soc_write(codec, 0x102, 0);
- }
- break;
-
case WM8958:
if (wm8994->revision == 0) {
/* Optimise performance for rev A */
- snd_soc_write(codec, 0x102, 0x3);
- snd_soc_write(codec, 0xcb, 0x81);
- snd_soc_write(codec, 0x817, 0);
- snd_soc_write(codec, 0x102, 0);
-
snd_soc_update_bits(codec,
WM8958_CHARGE_PUMP_2,
WM8958_CP_DISCH,
@@ -2117,13 +2100,7 @@ static int wm8994_set_bias_level(struct snd_soc_codec *codec,
}
break;
- case WM1811:
- if (wm8994->revision < 2) {
- snd_soc_write(codec, 0x102, 0x3);
- snd_soc_write(codec, 0x5d, 0x7e);
- snd_soc_write(codec, 0x5e, 0x0);
- snd_soc_write(codec, 0x102, 0x0);
- }
+ default:
break;
}
--
1.7.7.3
next prev parent reply other threads:[~2012-01-23 13:59 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-01-23 13:59 [PATCH 1/3] mfd: Add __devinit and __devexit annotations in wm8994 Mark Brown
2012-01-23 13:59 ` Mark Brown [this message]
2012-02-20 17:02 ` [PATCH 2/3] mfd/ASoC: Convert WM8994 driver to use regmap patches Samuel Ortiz
2012-01-23 13:59 ` [PATCH 3/3] ASoC: Convert the WM5100 revision A updates to a regmap patch Mark Brown
2012-02-20 17:03 ` [PATCH 1/3] mfd: Add __devinit and __devexit annotations in wm8994 Samuel Ortiz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1327327172-8411-2-git-send-email-broonie@opensource.wolfsonmicro.com \
--to=broonie@opensource.wolfsonmicro.com \
--cc=alsa-devel@alsa-project.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
--cc=patches@opensource.wolfsonmicro.com \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).