alsa-devel.alsa-project.org archive mirror
 help / color / mirror / Atom feed
From: Olivier Langlois <olivier@trillion01.com>
To: Anssi Hannula <anssi.hannula@iki.fi>
Cc: "Takashi Iwai" <tiwai@suse.de>,
	alsa-devel@alsa-project.org, "Rafał Miłecki" <zajec5@gmail.com>,
	linux-kernel@vger.kernel.org,
	"Peter Frühberger" <fritsch@xbmc.org>
Subject: Re: [RFC/RFT v2 0/4] ALSA: hda - hdmi: ATI/AMD multi-channel and HBR support
Date: Fri, 04 Oct 2013 03:06:11 -0400	[thread overview]
Message-ID: <1380870371.875.14.camel@Wailaba2> (raw)
In-Reply-To: <1380659456-3746-1-git-send-email-anssi.hannula@iki.fi>

Anssi,

Your patch has been applied on 3.11.3


> 
> I'm especially interested in testers with:
> 
> - Older codecs other than 0x1002aa01. My best guess still is that the
>   new code works on them as well.
>   o On these I'd like to know if multichannel and the new formats
>     work, i.e. e.g.
>     speaker-test -D hdmi:CARD=Generic,DEV=0 -c8 -r192000 -F S32_LE

This is working with Codec 0x1002aa01 revisions 0x100300 (Rev ID 3)
except for a small detail. I cannot tell if it is a regression from v1
of the patch or it was there and I did not noticed when I tested.

Rear left and rear right channels are flipped.

> 
> - Codec 0x1002aa01 revisions 0x100300 (Rev ID 3) or later (see
>   /proc/asound/cardX/codec#Y). These are HD7750+ I think. Stuff to be
>   tested on these:
>   o The ramp up/down stuff, i.e. patch 4. Is there any difference seen
>     with these, in the beginning/end (i.e. fade-out/in):
>     speaker-test -D hdmi:CARD=Generic,DEV=0,AES0=0x04 -c2 -r48000

No noticeable difference than when it is run without the AES0 param

>     speaker-test -D hdmi:CARD=Generic,DEV=0,AES0=0x06 -c2 -r48000

>From the application the sound is sent normally but no sound at all is
outputed from the speakers.

>     Also, is there a difference in the beginning of these
>     (maybe garbage sound and/or slightly slower startup?):
>     aplay -Dhdmi:CARD=Generic,DEV=0,AES0=4 -r44100 -f s16_le -c2 testi.dts.cut.spdif
>     aplay -Dhdmi:CARD=Generic,DEV=0,AES0=6 -r44100 -f s16_le -c2 testi.dts.cut.spdif

Both works. No garbage is heard from neither of them. maybe maybe AES04
starts playing few ms earlier but if there is a difference, it is
extremely subtle.
> 
>   o Contents of /proc/asound/cardX/eld#0. I'd like to see the contents
>     both with radeon and with the proprietary fglrx driver in use
> 
With fglrx 13.10 Beta 2:

lano1106@whippet2 /proc/asound/card0 $ cat codec#0 
Codec: ATI R6xx HDMI
Address: 0
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x1002aa01
Subsystem Id: 0x00aa0100
Revision Id: 0x100300
No Modem Function Group found
Default PCM:
    rates [0x70]: 32000 44100 48000
    bits [0x2]: 16
    formats [0x5]: PCM AC3
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
  Power states:  D0 D3 CLKSTOP EPSS
  Power: setting=D0, actual=D0, Clock-stop-OK
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x221: Stereo Digital Stripe
  Converter: stream=1, channel=0
  Digital: Enabled
  Digital category: 0x0
  IEC Coding Type: 0x0
Node 0x03 [Pin Complex] wcaps 0x400381: Stereo Digital
  Control: name="HDMI/DP,pcm=3 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=0, device=0
  Control: name="IEC958 Playback Pro Mask", index=0, device=0
  Control: name="IEC958 Playback Default", index=0, device=0
  Control: name="IEC958 Playback Switch", index=0, device=0
  Control: name="ELD", index=0, device=3
  Pincap 0x00000094: OUT Detect HDMI
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=01, enabled=1
  Connection: 1
     0x02
Node 0x04 [Audio Output] wcaps 0x221: Stereo Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
Node 0x05 [Pin Complex] wcaps 0x400381: Stereo Digital
  Control: name="HDMI/DP,pcm=7 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=1, device=0
  Control: name="IEC958 Playback Pro Mask", index=1, device=0
  Control: name="IEC958 Playback Default", index=1, device=0
  Control: name="IEC958 Playback Switch", index=1, device=0
  Control: name="ELD", index=0, device=7
  Pincap 0x00000094: OUT Detect HDMI
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=02, enabled=1
  Connection: 1
     0x04
Node 0x06 [Audio Output] wcaps 0x221: Stereo Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
Node 0x07 [Pin Complex] wcaps 0x400381: Stereo Digital
  Control: name="HDMI/DP,pcm=8 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=2, device=0
  Control: name="IEC958 Playback Pro Mask", index=2, device=0
  Control: name="IEC958 Playback Default", index=2, device=0
  Control: name="IEC958 Playback Switch", index=2, device=0
  Control: name="ELD", index=0, device=8
  Pincap 0x00000094: OUT Detect HDMI
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=03, enabled=1
  Connection: 1
     0x06
Node 0x08 [Audio Output] wcaps 0x221: Stereo Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
Node 0x09 [Pin Complex] wcaps 0x400381: Stereo Digital
  Control: name="HDMI/DP,pcm=9 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=3, device=0
  Control: name="IEC958 Playback Pro Mask", index=3, device=0
  Control: name="IEC958 Playback Default", index=3, device=0
  Control: name="IEC958 Playback Switch", index=3, device=0
  Control: name="ELD", index=0, device=9
  Pincap 0x00000094: OUT Detect HDMI
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=04, enabled=1
  Connection: 1
     0x08
Node 0x0a [Audio Output] wcaps 0x221: Stereo Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
Node 0x0b [Pin Complex] wcaps 0x400381: Stereo Digital
  Control: name="HDMI/DP,pcm=10 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=4, device=0
  Control: name="IEC958 Playback Pro Mask", index=4, device=0
  Control: name="IEC958 Playback Default", index=4, device=0
  Control: name="IEC958 Playback Switch", index=4, device=0
  Control: name="ELD", index=0, device=10
  Pincap 0x00000094: OUT Detect HDMI
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=05, enabled=1
  Connection: 1
     0x0a
Node 0x0c [Audio Output] wcaps 0x221: Stereo Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
Node 0x0d [Pin Complex] wcaps 0x400381: Stereo Digital
  Control: name="HDMI/DP,pcm=11 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=5, device=0
  Control: name="IEC958 Playback Pro Mask", index=5, device=0
  Control: name="IEC958 Playback Default", index=5, device=0
  Control: name="IEC958 Playback Switch", index=5, device=0
  Control: name="ELD", index=0, device=11
  Pincap 0x00000094: OUT Detect HDMI
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=06, enabled=1
  Connection: 1
     0x0c

  parent reply	other threads:[~2013-10-04  7:06 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-10-01 20:30 [RFC/RFT v2 0/4] ALSA: hda - hdmi: ATI/AMD multi-channel and HBR support Anssi Hannula
2013-10-01 20:30 ` [PATCH 1/4] ALSA: hda - hdmi: Add ATI/AMD multi-channel audio support Anssi Hannula
2013-10-30 15:35   ` Rafał Miłecki
2013-10-30 15:59     ` Anssi Hannula
2013-10-31 16:22       ` Rafał Miłecki
2013-10-31 20:26         ` Anssi Hannula
2013-10-31 23:25           ` Rafał Miłecki
2013-10-31 23:34             ` Anssi Hannula
2013-10-31 23:51               ` Rafał Miłecki
2013-10-31 23:58                 ` Anssi Hannula
2013-11-01 11:29                   ` Rafał Miłecki
2013-11-01 12:15                     ` Anssi Hannula
2013-11-01 13:22                       ` Rafał Miłecki
2013-11-01 13:43                         ` Rafał Miłecki
2013-10-01 20:30 ` [PATCH 2/4] ALSA: hda - hdmi: Add ELD emulation for ATI/AMD codecs Anssi Hannula
2013-10-01 20:30 ` [PATCH 3/4] ALSA: hda - hdmi: Add HBR bitstreaming support for ATI/AMD HDMI codecs Anssi Hannula
2013-10-01 20:30 ` [PATCH 4/4] ALSA: hda - hdmi: Disable ramp-up/down for non-PCM on AMD codecs Anssi Hannula
2013-10-02 14:34 ` [RFC/RFT v2 0/4] ALSA: hda - hdmi: ATI/AMD multi-channel and HBR support Takashi Iwai
2013-10-02 16:42   ` Anssi Hannula
2013-10-07  7:33     ` Takashi Iwai
2013-10-04  7:06 ` Olivier Langlois [this message]
2013-10-04 23:39   ` Anssi Hannula
2013-10-06  3:48     ` Olivier Langlois
2013-10-06 12:07       ` [alsa-devel] " Anssi Hannula
2013-10-09  4:32         ` Olivier Langlois
2013-10-24 19:06           ` Anssi Hannula
2013-11-07 21:20             ` Olivier Langlois
2013-11-08 10:18               ` Anssi Hannula
2013-11-08 16:44                 ` Olivier Langlois
2013-11-08 22:13                   ` Anssi Hannula

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1380870371.875.14.camel@Wailaba2 \
    --to=olivier@trillion01.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=anssi.hannula@iki.fi \
    --cc=fritsch@xbmc.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=tiwai@suse.de \
    --cc=zajec5@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).