[PATCH v2 00/13] ASoC: Intel: Skylake: Driver updates

[PATCH v2 00/13] ASoC: Intel: Skylake: Driver updates

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

This patch series includes driver updates for the handling scenarios 
during System S0/S3 transitions when audio stream is stopped during
system.
o move DMA configuration in DSP Gateway Module widget event handler to
ensure DMA is configured after resume. 
o Enable SSP MLCK using Supply widget. This will ensure the MCLK is
enabled when the widget is power on.
o Check DMA decouple register state before coupling/decoupling the DMA.
o In case of HDMI pass-through pipe, reset only the FE Pipe when stream
in in XRUN state.
o Resume the stream from HW renderer position.
o HDMI Codec pin and converter state need to be restored when stream
is resumed.

Changes in v2:
 - Addressed Mark's comment on patch 1, split this into 2 as this had
additional changes other than configuring the DMA.
 - Addressed Takashi's comment on the usage of snd_hdac_updatel() 

Jeeja KP (13):
  ASoC: Intel: Skylake: Update link_index and format in pipe params
  ASoC: Intel: Skylake: Add helper function to setup host/link dma
  ASoC: Intel: Skylake: Configure DMA in PRE_PMD handler of Mixer
  ASoC: Intel: Skylake: Removed unused skl_get_format()
  ALSA: hda: check stream decoupled register state
  ASoC: Intel: Skylake: Add set_tristate DAI ops to enable SSP MCLK
  ASoC: Intel: Skylake: Remove unused SSP BE prepare DAI ops
  ASoC: Intel: Skylake: Add supply widget as non DSP widget
  ASoC: Intel: Skylake: Add supply widget in skl_nau_max machine
  ASoC: Intel: Skylake: Add supply widget in bxt_da_max machine
  ASoC: Intel: Skylake: Don't reset pass-through pipe in BE prepare
  ASoC: Intel: Skylake: set the resume point to LPIB
  ASoC: hdac_hdmi: Enable pin and converter in prepare

 sound/hda/ext/hdac_ext_stream.c                 |  15 +-
 sound/soc/codecs/hdac_hdmi.c                    |  28 ++--
 sound/soc/intel/boards/bxt_da7219_max98357a.c   |  34 ++++
 sound/soc/intel/boards/skl_nau88l25_max98357a.c |  34 ++++
 sound/soc/intel/skylake/skl-pcm.c               | 210 +++++++++++++-----------
 sound/soc/intel/skylake/skl-topology.c          |  27 ++-
 sound/soc/intel/skylake/skl-topology.h          |   6 +
 7 files changed, 240 insertions(+), 114 deletions(-)

-- 
2.5.0

[PATCH v2 01/13] ASoC: Intel: Skylake: Update link_index and format in pipe params

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

To configure Host/Link DMA, additionally link index and format
are required based on the hw params. So added these parameters in
the pipe params and in hw_params the pipe params are updated.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c      | 8 ++++++++
 sound/soc/intel/skylake/skl-topology.c | 2 ++
 sound/soc/intel/skylake/skl-topology.h | 2 ++
 3 files changed, 12 insertions(+)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 84b5101..105aab7 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -292,6 +292,7 @@ static int skl_pcm_hw_params(struct snd_pcm_substream *substream,
 	p_params.s_freq = params_rate(params);
 	p_params.host_dma_id = dma_id;
 	p_params.stream = substream->stream;
+	p_params.format = params_format(params);
 
 	m_cfg = skl_tplg_fe_get_cpr_module(dai, p_params.stream);
 	if (m_cfg)
@@ -506,6 +507,7 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 	struct hdac_ext_dma_params *dma_params;
 	struct snd_soc_dai *codec_dai = rtd->codec_dai;
 	struct skl_pipe_params p_params = {0};
+	struct hdac_ext_link *link;
 
 	link_dev = snd_hdac_ext_stream_assign(ebus, substream,
 					HDAC_EXT_STREAM_TYPE_LINK);
@@ -514,6 +516,10 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 
 	snd_soc_dai_set_dma_data(dai, substream, (void *)link_dev);
 
+	link = snd_hdac_ext_bus_get_link(ebus, rtd->codec->component.name);
+	if (!link)
+		return -EINVAL;
+
 	/* set the stream tag in the codec dai dma params  */
 	dma_params = snd_soc_dai_get_dma_data(codec_dai, substream);
 	if (dma_params)
@@ -524,6 +530,8 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 	p_params.s_freq = params_rate(params);
 	p_params.stream = substream->stream;
 	p_params.link_dma_id = hdac_stream(link_dev)->stream_tag - 1;
+	p_params.link_index = link->index;
+	p_params.format = params_format(params);
 
 	return skl_tplg_be_update_params(dai, &p_params);
 }
diff --git a/sound/soc/intel/skylake/skl-topology.c b/sound/soc/intel/skylake/skl-topology.c
index bd313c9..484d451 100644
--- a/sound/soc/intel/skylake/skl-topology.c
+++ b/sound/soc/intel/skylake/skl-topology.c
@@ -1207,6 +1207,7 @@ static void skl_tplg_fill_dma_id(struct skl_module_cfg *mcfg,
 		switch (mcfg->dev_type) {
 		case SKL_DEVICE_HDALINK:
 			pipe->p_params->link_dma_id = params->link_dma_id;
+			pipe->p_params->link_index = params->link_index;
 			break;
 
 		case SKL_DEVICE_HDAHOST:
@@ -1220,6 +1221,7 @@ static void skl_tplg_fill_dma_id(struct skl_module_cfg *mcfg,
 		pipe->p_params->ch = params->ch;
 		pipe->p_params->s_freq = params->s_freq;
 		pipe->p_params->stream = params->stream;
+		pipe->p_params->format = params->format;
 
 	} else {
 		memcpy(pipe->p_params, params, sizeof(*params));
diff --git a/sound/soc/intel/skylake/skl-topology.h b/sound/soc/intel/skylake/skl-topology.h
index 08d3928..405765f 100644
--- a/sound/soc/intel/skylake/skl-topology.h
+++ b/sound/soc/intel/skylake/skl-topology.h
@@ -254,6 +254,8 @@ struct skl_pipe_params {
 	u32 s_freq;
 	u32 s_fmt;
 	u8 linktype;
+	snd_pcm_format_t format;
+	int link_index;
 	int stream;
 };
 
-- 
2.5.0

Applied "ASoC: Intel: Skylake: Update link_index and format in pipe params" to the asoc tree

[Mark Brown]

The patch

   ASoC: Intel: Skylake: Update link_index and format in pipe params

has been applied to the asoc tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 12c3be0e720fe8c4e0f456fd25a6dcc8b254606c Mon Sep 17 00:00:00 2001
From: Jeeja KP <jeeja.kp@intel.com>
Date: Thu, 8 Dec 2016 13:41:12 +0530
Subject: [PATCH] ASoC: Intel: Skylake: Update link_index and format in pipe
 params

To configure Host/Link DMA, additionally link index and format
are required based on the hw params. So added these parameters in
the pipe params and in hw_params the pipe params are updated.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 sound/soc/intel/skylake/skl-pcm.c      | 8 ++++++++
 sound/soc/intel/skylake/skl-topology.c | 2 ++
 sound/soc/intel/skylake/skl-topology.h | 2 ++
 3 files changed, 12 insertions(+)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 84b5101e6ca6..105aab7593c8 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -292,6 +292,7 @@ static int skl_pcm_hw_params(struct snd_pcm_substream *substream,
 	p_params.s_freq = params_rate(params);
 	p_params.host_dma_id = dma_id;
 	p_params.stream = substream->stream;
+	p_params.format = params_format(params);
 
 	m_cfg = skl_tplg_fe_get_cpr_module(dai, p_params.stream);
 	if (m_cfg)
@@ -506,6 +507,7 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 	struct hdac_ext_dma_params *dma_params;
 	struct snd_soc_dai *codec_dai = rtd->codec_dai;
 	struct skl_pipe_params p_params = {0};
+	struct hdac_ext_link *link;
 
 	link_dev = snd_hdac_ext_stream_assign(ebus, substream,
 					HDAC_EXT_STREAM_TYPE_LINK);
@@ -514,6 +516,10 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 
 	snd_soc_dai_set_dma_data(dai, substream, (void *)link_dev);
 
+	link = snd_hdac_ext_bus_get_link(ebus, rtd->codec->component.name);
+	if (!link)
+		return -EINVAL;
+
 	/* set the stream tag in the codec dai dma params  */
 	dma_params = snd_soc_dai_get_dma_data(codec_dai, substream);
 	if (dma_params)
@@ -524,6 +530,8 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 	p_params.s_freq = params_rate(params);
 	p_params.stream = substream->stream;
 	p_params.link_dma_id = hdac_stream(link_dev)->stream_tag - 1;
+	p_params.link_index = link->index;
+	p_params.format = params_format(params);
 
 	return skl_tplg_be_update_params(dai, &p_params);
 }
diff --git a/sound/soc/intel/skylake/skl-topology.c b/sound/soc/intel/skylake/skl-topology.c
index eb440cd9a2a4..8f608c45e445 100644
--- a/sound/soc/intel/skylake/skl-topology.c
+++ b/sound/soc/intel/skylake/skl-topology.c
@@ -1206,6 +1206,7 @@ static void skl_tplg_fill_dma_id(struct skl_module_cfg *mcfg,
 		switch (mcfg->dev_type) {
 		case SKL_DEVICE_HDALINK:
 			pipe->p_params->link_dma_id = params->link_dma_id;
+			pipe->p_params->link_index = params->link_index;
 			break;
 
 		case SKL_DEVICE_HDAHOST:
@@ -1219,6 +1220,7 @@ static void skl_tplg_fill_dma_id(struct skl_module_cfg *mcfg,
 		pipe->p_params->ch = params->ch;
 		pipe->p_params->s_freq = params->s_freq;
 		pipe->p_params->stream = params->stream;
+		pipe->p_params->format = params->format;
 
 	} else {
 		memcpy(pipe->p_params, params, sizeof(*params));
diff --git a/sound/soc/intel/skylake/skl-topology.h b/sound/soc/intel/skylake/skl-topology.h
index 08d39280b07b..405765f3a6b5 100644
--- a/sound/soc/intel/skylake/skl-topology.h
+++ b/sound/soc/intel/skylake/skl-topology.h
@@ -254,6 +254,8 @@ struct skl_pipe_params {
 	u32 s_freq;
 	u32 s_fmt;
 	u8 linktype;
+	snd_pcm_format_t format;
+	int link_index;
 	int stream;
 };
 
-- 
2.11.0

[PATCH v2 02/13] ASoC: Intel: Skylake: Add helper function to setup host/link dma

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

This patch adds helper function to configure the host/link DMA when
the DMA is in decoupled mode.
Next patch adds the usage of this helper routines for configuring
DMA in Mixer event handler.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c      | 74 ++++++++++++++++++++++++++++++++++
 sound/soc/intel/skylake/skl-topology.h |  4 ++
 2 files changed, 78 insertions(+)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 105aab7..8a7b6f7 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -137,6 +137,80 @@ static void skl_set_suspend_active(struct snd_pcm_substream *substream,
 		skl->supend_active--;
 }
 
+int skl_pcm_host_dma_prepare(struct device *dev, struct skl_pipe_params *params)
+{
+	struct hdac_ext_bus *ebus = dev_get_drvdata(dev);
+	struct hdac_bus *bus = ebus_to_hbus(ebus);
+	unsigned int format_val;
+	struct hdac_stream *hstream;
+	struct hdac_ext_stream *stream;
+	int err;
+
+	hstream = snd_hdac_get_stream(bus, params->stream,
+					params->host_dma_id + 1);
+	if (!hstream)
+		return -EINVAL;
+
+	stream = stream_to_hdac_ext_stream(hstream);
+	snd_hdac_ext_stream_decouple(ebus, stream, true);
+
+	format_val = snd_hdac_calc_stream_format(params->s_freq,
+				params->ch, params->format, 32, 0);
+
+	dev_dbg(dev, "format_val=%d, rate=%d, ch=%d, format=%d\n",
+		format_val, params->s_freq, params->ch, params->format);
+
+	snd_hdac_stream_reset(hdac_stream(stream));
+	err = snd_hdac_stream_set_params(hdac_stream(stream), format_val);
+	if (err < 0)
+		return err;
+
+	err = snd_hdac_stream_setup(hdac_stream(stream));
+	if (err < 0)
+		return err;
+
+	hdac_stream(stream)->prepared = 1;
+
+	return 0;
+}
+
+int skl_pcm_link_dma_prepare(struct device *dev, struct skl_pipe_params *params)
+{
+	struct hdac_ext_bus *ebus = dev_get_drvdata(dev);
+	struct hdac_bus *bus = ebus_to_hbus(ebus);
+	unsigned int format_val;
+	struct hdac_stream *hstream;
+	struct hdac_ext_stream *stream;
+	struct hdac_ext_link *link;
+
+	hstream = snd_hdac_get_stream(bus, params->stream,
+					params->link_dma_id + 1);
+	if (!hstream)
+		return -EINVAL;
+
+	stream = stream_to_hdac_ext_stream(hstream);
+	snd_hdac_ext_stream_decouple(ebus, stream, true);
+	format_val = snd_hdac_calc_stream_format(params->s_freq,
+				params->ch, params->format, 24, 0);
+
+	dev_dbg(dev, "format_val=%d, rate=%d, ch=%d, format=%d\n",
+		format_val, params->s_freq, params->ch, params->format);
+
+	snd_hdac_ext_link_stream_reset(stream);
+
+	snd_hdac_ext_link_stream_setup(stream, format_val);
+
+	list_for_each_entry(link, &ebus->hlink_list, list) {
+		if (link->index == params->link_index)
+			snd_hdac_ext_link_set_stream_id(link,
+					hstream->stream_tag);
+	}
+
+	stream->link_prepared = 1;
+
+	return 0;
+}
+
 static int skl_pcm_open(struct snd_pcm_substream *substream,
 		struct snd_soc_dai *dai)
 {
diff --git a/sound/soc/intel/skylake/skl-topology.h b/sound/soc/intel/skylake/skl-topology.h
index 405765f..a0d3158 100644
--- a/sound/soc/intel/skylake/skl-topology.h
+++ b/sound/soc/intel/skylake/skl-topology.h
@@ -385,4 +385,8 @@ int skl_get_module_params(struct skl_sst *ctx, u32 *params, int size,
 struct skl_module_cfg *skl_tplg_be_get_cpr_module(struct snd_soc_dai *dai,
 								int stream);
 enum skl_bitdepth skl_get_bit_depth(int params);
+int skl_pcm_host_dma_prepare(struct device *dev,
+			struct skl_pipe_params *params);
+int skl_pcm_link_dma_prepare(struct device *dev,
+			struct skl_pipe_params *params);
 #endif
-- 
2.5.0

Applied "ASoC: Intel: Skylake: Add helper function to setup host/link dma" to the asoc tree

[Mark Brown]

The patch

   ASoC: Intel: Skylake: Add helper function to setup host/link dma

has been applied to the asoc tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From ad036bdee57ab2287535fe53864bb5154e101991 Mon Sep 17 00:00:00 2001
From: Jeeja KP <jeeja.kp@intel.com>
Date: Thu, 8 Dec 2016 13:41:13 +0530
Subject: [PATCH] ASoC: Intel: Skylake: Add helper function to setup host/link
 dma

This patch adds helper function to configure the host/link DMA when
the DMA is in decoupled mode.
Next patch adds the usage of this helper routines for configuring
DMA in Mixer event handler.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 sound/soc/intel/skylake/skl-pcm.c      | 74 ++++++++++++++++++++++++++++++++++
 sound/soc/intel/skylake/skl-topology.h |  4 ++
 2 files changed, 78 insertions(+)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index aebae234152c..1abff8e1a298 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -137,6 +137,80 @@ static void skl_set_suspend_active(struct snd_pcm_substream *substream,
 		skl->supend_active--;
 }
 
+int skl_pcm_host_dma_prepare(struct device *dev, struct skl_pipe_params *params)
+{
+	struct hdac_ext_bus *ebus = dev_get_drvdata(dev);
+	struct hdac_bus *bus = ebus_to_hbus(ebus);
+	unsigned int format_val;
+	struct hdac_stream *hstream;
+	struct hdac_ext_stream *stream;
+	int err;
+
+	hstream = snd_hdac_get_stream(bus, params->stream,
+					params->host_dma_id + 1);
+	if (!hstream)
+		return -EINVAL;
+
+	stream = stream_to_hdac_ext_stream(hstream);
+	snd_hdac_ext_stream_decouple(ebus, stream, true);
+
+	format_val = snd_hdac_calc_stream_format(params->s_freq,
+				params->ch, params->format, 32, 0);
+
+	dev_dbg(dev, "format_val=%d, rate=%d, ch=%d, format=%d\n",
+		format_val, params->s_freq, params->ch, params->format);
+
+	snd_hdac_stream_reset(hdac_stream(stream));
+	err = snd_hdac_stream_set_params(hdac_stream(stream), format_val);
+	if (err < 0)
+		return err;
+
+	err = snd_hdac_stream_setup(hdac_stream(stream));
+	if (err < 0)
+		return err;
+
+	hdac_stream(stream)->prepared = 1;
+
+	return 0;
+}
+
+int skl_pcm_link_dma_prepare(struct device *dev, struct skl_pipe_params *params)
+{
+	struct hdac_ext_bus *ebus = dev_get_drvdata(dev);
+	struct hdac_bus *bus = ebus_to_hbus(ebus);
+	unsigned int format_val;
+	struct hdac_stream *hstream;
+	struct hdac_ext_stream *stream;
+	struct hdac_ext_link *link;
+
+	hstream = snd_hdac_get_stream(bus, params->stream,
+					params->link_dma_id + 1);
+	if (!hstream)
+		return -EINVAL;
+
+	stream = stream_to_hdac_ext_stream(hstream);
+	snd_hdac_ext_stream_decouple(ebus, stream, true);
+	format_val = snd_hdac_calc_stream_format(params->s_freq,
+				params->ch, params->format, 24, 0);
+
+	dev_dbg(dev, "format_val=%d, rate=%d, ch=%d, format=%d\n",
+		format_val, params->s_freq, params->ch, params->format);
+
+	snd_hdac_ext_link_stream_reset(stream);
+
+	snd_hdac_ext_link_stream_setup(stream, format_val);
+
+	list_for_each_entry(link, &ebus->hlink_list, list) {
+		if (link->index == params->link_index)
+			snd_hdac_ext_link_set_stream_id(link,
+					hstream->stream_tag);
+	}
+
+	stream->link_prepared = 1;
+
+	return 0;
+}
+
 static int skl_pcm_open(struct snd_pcm_substream *substream,
 		struct snd_soc_dai *dai)
 {
diff --git a/sound/soc/intel/skylake/skl-topology.h b/sound/soc/intel/skylake/skl-topology.h
index 405765f3a6b5..a0d3158196f0 100644
--- a/sound/soc/intel/skylake/skl-topology.h
+++ b/sound/soc/intel/skylake/skl-topology.h
@@ -385,4 +385,8 @@ int skl_get_module_params(struct skl_sst *ctx, u32 *params, int size,
 struct skl_module_cfg *skl_tplg_be_get_cpr_module(struct snd_soc_dai *dai,
 								int stream);
 enum skl_bitdepth skl_get_bit_depth(int params);
+int skl_pcm_host_dma_prepare(struct device *dev,
+			struct skl_pipe_params *params);
+int skl_pcm_link_dma_prepare(struct device *dev,
+			struct skl_pipe_params *params);
 #endif
-- 
2.11.0

[PATCH v2 03/13] ASoC: Intel: Skylake: Configure DMA in PRE_PMD handler of Mixer

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

If system is suspended when PCM was paused/stopped, restart doesn't
configure DMA as it is we are in Pause state and results in IO error
eventually.

Configure host/link DMA before initializing DSP Gateway copier module
instead of DAI prepare(). So moved DMA configuration to mixer PRE_PMD
widget handler instead of DAI prepare.

This uses previously added new API to do the configuration and removes
old DAI prepare code.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c      | 50 +---------------------------------
 sound/soc/intel/skylake/skl-topology.c | 19 +++++++++++++
 2 files changed, 20 insertions(+), 49 deletions(-)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 8a7b6f7..1abff8e 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -305,37 +305,19 @@ static int skl_be_prepare(struct snd_pcm_substream *substream,
 static int skl_pcm_prepare(struct snd_pcm_substream *substream,
 		struct snd_soc_dai *dai)
 {
-	struct hdac_ext_stream *stream = get_hdac_ext_stream(substream);
 	struct skl *skl = get_skl_ctx(dai->dev);
-	unsigned int format_val;
-	int err;
 	struct skl_module_cfg *mconfig;
 
 	dev_dbg(dai->dev, "%s: %s\n", __func__, dai->name);
 
 	mconfig = skl_tplg_fe_get_cpr_module(dai, substream->stream);
 
-	format_val = skl_get_format(substream, dai);
-	dev_dbg(dai->dev, "stream_tag=%d formatvalue=%d\n",
-				hdac_stream(stream)->stream_tag, format_val);
-	snd_hdac_stream_reset(hdac_stream(stream));
-
 	/* In case of XRUN recovery, reset the FW pipe to clean state */
 	if (mconfig && (substream->runtime->status->state ==
 					SNDRV_PCM_STATE_XRUN))
 		skl_reset_pipe(skl->skl_sst, mconfig->pipe);
 
-	err = snd_hdac_stream_set_params(hdac_stream(stream), format_val);
-	if (err < 0)
-		return err;
-
-	err = snd_hdac_stream_setup(hdac_stream(stream));
-	if (err < 0)
-		return err;
-
-	hdac_stream(stream)->prepared = 1;
-
-	return err;
+	return 0;
 }
 
 static int skl_pcm_hw_params(struct snd_pcm_substream *substream,
@@ -510,7 +492,6 @@ static int skl_pcm_trigger(struct snd_pcm_substream *substream, int cmd,
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_RESUME:
 		if (!w->ignore_suspend) {
-			skl_pcm_prepare(substream, dai);
 			/*
 			 * enable DMA Resume enable bit for the stream, set the
 			 * dpib & lpib position to resume before starting the
@@ -531,7 +512,6 @@ static int skl_pcm_trigger(struct snd_pcm_substream *substream, int cmd,
 		 * pipeline is started but there is a delay in starting the
 		 * DMA channel on the host.
 		 */
-		snd_hdac_ext_stream_decouple(ebus, stream, true);
 		ret = skl_decoupled_trigger(substream, cmd);
 		if (ret < 0)
 			return ret;
@@ -613,41 +593,15 @@ static int skl_link_hw_params(struct snd_pcm_substream *substream,
 static int skl_link_pcm_prepare(struct snd_pcm_substream *substream,
 		struct snd_soc_dai *dai)
 {
-	struct snd_soc_pcm_runtime *rtd = snd_pcm_substream_chip(substream);
-	struct hdac_ext_bus *ebus = dev_get_drvdata(dai->dev);
-	struct hdac_ext_stream *link_dev =
-			snd_soc_dai_get_dma_data(dai, substream);
-	unsigned int format_val = 0;
-	struct skl_dma_params *dma_params;
-	struct snd_soc_dai *codec_dai = rtd->codec_dai;
-	struct hdac_ext_link *link;
 	struct skl *skl = get_skl_ctx(dai->dev);
 	struct skl_module_cfg *mconfig = NULL;
 
-	dma_params  = (struct skl_dma_params *)
-			snd_soc_dai_get_dma_data(codec_dai, substream);
-	if (dma_params)
-		format_val = dma_params->format;
-	dev_dbg(dai->dev, "stream_tag=%d formatvalue=%d codec_dai_name=%s\n",
-			hdac_stream(link_dev)->stream_tag, format_val, codec_dai->name);
-
-	link = snd_hdac_ext_bus_get_link(ebus, rtd->codec->component.name);
-	if (!link)
-		return -EINVAL;
-
-	snd_hdac_ext_link_stream_reset(link_dev);
-
 	/* In case of XRUN recovery, reset the FW pipe to clean state */
 	mconfig = skl_tplg_be_get_cpr_module(dai, substream->stream);
 	if (mconfig && (substream->runtime->status->state ==
 					SNDRV_PCM_STATE_XRUN))
 		skl_reset_pipe(skl->skl_sst, mconfig->pipe);
 
-	snd_hdac_ext_link_stream_setup(link_dev, format_val);
-
-	snd_hdac_ext_link_set_stream_id(link, hdac_stream(link_dev)->stream_tag);
-	link_dev->link_prepared = 1;
-
 	return 0;
 }
 
@@ -662,10 +616,8 @@ static int skl_link_pcm_trigger(struct snd_pcm_substream *substream,
 	dev_dbg(dai->dev, "In %s cmd=%d\n", __func__, cmd);
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_RESUME:
-		skl_link_pcm_prepare(substream, dai);
 	case SNDRV_PCM_TRIGGER_START:
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
-		snd_hdac_ext_stream_decouple(ebus, stream, true);
 		snd_hdac_ext_link_stream_start(link_dev);
 		break;
 
diff --git a/sound/soc/intel/skylake/skl-topology.c b/sound/soc/intel/skylake/skl-topology.c
index 484d451..9cf8c51 100644
--- a/sound/soc/intel/skylake/skl-topology.c
+++ b/sound/soc/intel/skylake/skl-topology.c
@@ -496,6 +496,20 @@ static int skl_tplg_set_module_init_data(struct snd_soc_dapm_widget *w)
 	return 0;
 }
 
+static int skl_tplg_module_prepare(struct skl_sst *ctx, struct skl_pipe *pipe,
+		struct snd_soc_dapm_widget *w, struct skl_module_cfg *mcfg)
+{
+	switch (mcfg->dev_type) {
+	case SKL_DEVICE_HDAHOST:
+		return skl_pcm_host_dma_prepare(ctx->dev, pipe->p_params);
+
+	case SKL_DEVICE_HDALINK:
+		return skl_pcm_link_dma_prepare(ctx->dev, pipe->p_params);
+	}
+
+	return 0;
+}
+
 /*
  * Inside a pipe instance, we can have various modules. These modules need
  * to instantiated in DSP by invoking INIT_MODULE IPC, which is achieved by
@@ -535,6 +549,11 @@ skl_tplg_init_pipe_modules(struct skl *skl, struct skl_pipe *pipe)
 			mconfig->m_state = SKL_MODULE_LOADED;
 		}
 
+		/* prepare the DMA if the module is gateway cpr */
+		ret = skl_tplg_module_prepare(ctx, pipe, w, mconfig);
+		if (ret < 0)
+			return ret;
+
 		/* update blob if blob is null for be with default value */
 		skl_tplg_update_be_blob(w, ctx);
 
-- 
2.5.0

[PATCH v2 04/13] ASoC: Intel: Skylake: Removed unused skl_get_format()

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Removed the unused function skl_get_format as the format is calculated
directly using the HDA core API.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c | 26 --------------------------
 1 file changed, 26 deletions(-)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 1abff8e..10fa10d 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -259,32 +259,6 @@ static int skl_pcm_open(struct snd_pcm_substream *substream,
 	return 0;
 }
 
-static int skl_get_format(struct snd_pcm_substream *substream,
-		struct snd_soc_dai *dai)
-{
-	struct snd_soc_pcm_runtime *rtd = snd_pcm_substream_chip(substream);
-	struct skl_dma_params *dma_params;
-	struct hdac_ext_bus *ebus = dev_get_drvdata(dai->dev);
-	int format_val = 0;
-
-	if ((ebus_to_hbus(ebus))->ppcap) {
-		struct snd_pcm_runtime *runtime = substream->runtime;
-
-		format_val = snd_hdac_calc_stream_format(runtime->rate,
-						runtime->channels,
-						runtime->format,
-						32, 0);
-	} else {
-		struct snd_soc_dai *codec_dai = rtd->codec_dai;
-
-		dma_params = snd_soc_dai_get_dma_data(codec_dai, substream);
-		if (dma_params)
-			format_val = dma_params->format;
-	}
-
-	return format_val;
-}
-
 static int skl_be_prepare(struct snd_pcm_substream *substream,
 		struct snd_soc_dai *dai)
 {
-- 
2.5.0

[PATCH v2 05/13] ALSA: hda: check stream decoupled register state

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Check stream decoupled register value with requested value
before decoupling/coupling the stream.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/hda/ext/hdac_ext_stream.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/sound/hda/ext/hdac_ext_stream.c b/sound/hda/ext/hdac_ext_stream.c
index 3be051a..f35b006 100644
--- a/sound/hda/ext/hdac_ext_stream.c
+++ b/sound/hda/ext/hdac_ext_stream.c
@@ -128,14 +128,17 @@ void snd_hdac_ext_stream_decouple(struct hdac_ext_bus *ebus,
 {
 	struct hdac_stream *hstream = &stream->hstream;
 	struct hdac_bus *bus = &ebus->bus;
+	u32 val;
+	int mask = AZX_PPCTL_PROCEN(hstream->index);
 
 	spin_lock_irq(&bus->reg_lock);
-	if (decouple)
-		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, 0,
-				AZX_PPCTL_PROCEN(hstream->index));
-	else
-		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL,
-					AZX_PPCTL_PROCEN(hstream->index), 0);
+	val = ((readw(bus->ppcap + AZX_REG_PP_PPCTL) & mask) >> mask);
+
+	if (decouple && (val == 0))
+		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, mask);
+	else if (!decouple && (val > 0))
+		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, 0);
+
 	stream->decoupled = decouple;
 	spin_unlock_irq(&bus->reg_lock);
 }
-- 
2.5.0

Re: [PATCH v2 05/13] ALSA: hda: check stream decoupled register state

[Takashi Iwai]

On Wed, 07 Dec 2016 14:44:27 +0100,
jeeja.kp@intel.com wrote:
> 
> From: Jeeja KP <jeeja.kp@intel.com>
> 
> Check stream decoupled register value with requested value
> before decoupling/coupling the stream.
> 
> Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
> ---
>  sound/hda/ext/hdac_ext_stream.c | 15 +++++++++------
>  1 file changed, 9 insertions(+), 6 deletions(-)
> 
> diff --git a/sound/hda/ext/hdac_ext_stream.c b/sound/hda/ext/hdac_ext_stream.c
> index 3be051a..f35b006 100644
> --- a/sound/hda/ext/hdac_ext_stream.c
> +++ b/sound/hda/ext/hdac_ext_stream.c
> @@ -128,14 +128,17 @@ void snd_hdac_ext_stream_decouple(struct hdac_ext_bus *ebus,
>  {
>  	struct hdac_stream *hstream = &stream->hstream;
>  	struct hdac_bus *bus = &ebus->bus;
> +	u32 val;
> +	int mask = AZX_PPCTL_PROCEN(hstream->index);
>  
>  	spin_lock_irq(&bus->reg_lock);
> -	if (decouple)
> -		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, 0,
> -				AZX_PPCTL_PROCEN(hstream->index));
> -	else
> -		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL,
> -					AZX_PPCTL_PROCEN(hstream->index), 0);
> +	val = ((readw(bus->ppcap + AZX_REG_PP_PPCTL) & mask) >> mask);

This looks wrong.
And you just need to know whether it's zero or not in below, so the
shift is anyway superfluous.


Takashi


> +	if (decouple && (val == 0))
> +		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, mask);
> +	else if (!decouple && (val > 0))
> +		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, 0);
> +
>  	stream->decoupled = decouple;
>  	spin_unlock_irq(&bus->reg_lock);
>  }
> -- 
> 2.5.0
> 

Re: [PATCH v2 05/13] ALSA: hda: check stream decoupled register state

[Jeeja KP]

On Wed, Dec 07, 2016 at 02:41:59PM +0100, Takashi Iwai wrote:
> On Wed, 07 Dec 2016 14:44:27 +0100,
> jeeja.kp@intel.com wrote:
> > 
> > From: Jeeja KP <jeeja.kp@intel.com>
> > 
> > Check stream decoupled register value with requested value
> > before decoupling/coupling the stream.
> > 
> > Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
> > ---
> >  sound/hda/ext/hdac_ext_stream.c | 15 +++++++++------
> >  1 file changed, 9 insertions(+), 6 deletions(-)
> > 
> > diff --git a/sound/hda/ext/hdac_ext_stream.c b/sound/hda/ext/hdac_ext_stream.c
> > index 3be051a..f35b006 100644
> > --- a/sound/hda/ext/hdac_ext_stream.c
> > +++ b/sound/hda/ext/hdac_ext_stream.c
> > @@ -128,14 +128,17 @@ void snd_hdac_ext_stream_decouple(struct hdac_ext_bus *ebus,
> >  {
> >  	struct hdac_stream *hstream = &stream->hstream;
> >  	struct hdac_bus *bus = &ebus->bus;
> > +	u32 val;
> > +	int mask = AZX_PPCTL_PROCEN(hstream->index);
> >  
> >  	spin_lock_irq(&bus->reg_lock);
> > -	if (decouple)
> > -		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, 0,
> > -				AZX_PPCTL_PROCEN(hstream->index));
> > -	else
> > -		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL,
> > -					AZX_PPCTL_PROCEN(hstream->index), 0);
> > +	val = ((readw(bus->ppcap + AZX_REG_PP_PPCTL) & mask) >> mask);
> 
> This looks wrong.
> And you just need to know whether it's zero or not in below, so the
> shift is anyway superfluous.
Yes, shift is superfluous here. I will fix this.

> 
> 
> Takashi
> 
> 
> > +	if (decouple && (val == 0))
> > +		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, mask);
> > +	else if (!decouple && (val > 0))
> > +		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, 0);
> > +
> >  	stream->decoupled = decouple;
> >  	spin_unlock_irq(&bus->reg_lock);
> >  }
> > -- 
> > 2.5.0
> > 

-- 

[PATCH v2 06/13] ASoC: Intel: Skylake: Add set_tristate DAI ops to enable SSP MCLK

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Some machine requires MCLK to be enabled before SSP start up, so add
set_tristate() DAI ops to enable/disable SSP MCLK. This ops will be
called from machine which requires early MCLK and removes the usage of
enabling early MLCK in platform DAI prepare by default which is not
machine specific.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c | 29 ++++++++++++++++++++++++++++-
 1 file changed, 28 insertions(+), 1 deletion(-)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 10fa10d..3c16d41 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -396,6 +396,33 @@ static int skl_be_hw_params(struct snd_pcm_substream *substream,
 	return skl_tplg_be_update_params(dai, &p_params);
 }
 
+static int skl_soc_dai_set_tristate(struct snd_soc_dai *dai, int tristate)
+{
+	struct skl *skl = get_skl_ctx(dai->dev);
+	struct skl_sst *ctx = skl->skl_sst;
+	struct skl_module_cfg *mconfig;
+	int stream;
+
+	if (dai->playback_active)
+		stream = SNDRV_PCM_STREAM_PLAYBACK;
+	else
+		stream = SNDRV_PCM_STREAM_CAPTURE;
+
+	mconfig = skl_tplg_be_get_cpr_module(dai, stream);
+	if (!mconfig)
+		return -EINVAL;
+
+	/*
+	 * To enable ssp clk explicitly before gateway copier is configured,
+	 * need to use dma control IPC.
+	 * Disable will be done when DSP gateway copier modules are deleted.
+	 */
+	if (!tristate)
+		return skl_dsp_set_dma_control(ctx, mconfig);
+
+	return 0;
+}
+
 static int skl_decoupled_trigger(struct snd_pcm_substream *substream,
 		int cmd)
 {
@@ -646,7 +673,7 @@ static struct snd_soc_dai_ops skl_dmic_dai_ops = {
 
 static struct snd_soc_dai_ops skl_be_ssp_dai_ops = {
 	.hw_params = skl_be_hw_params,
-	.prepare = skl_be_prepare,
+	.set_tristate = skl_soc_dai_set_tristate,
 };
 
 static struct snd_soc_dai_ops skl_link_dai_ops = {
-- 
2.5.0

[PATCH v2 07/13] ASoC: Intel: Skylake: Remove unused SSP BE prepare DAI ops

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Removed unused prepare DAI ops as previous patch uses set_tristate
ops and this is no longer in use so remove the BE DAI prepare opd.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c | 17 -----------------
 1 file changed, 17 deletions(-)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 3c16d41..688d6f7 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -259,23 +259,6 @@ static int skl_pcm_open(struct snd_pcm_substream *substream,
 	return 0;
 }
 
-static int skl_be_prepare(struct snd_pcm_substream *substream,
-		struct snd_soc_dai *dai)
-{
-	struct skl *skl = get_skl_ctx(dai->dev);
-	struct skl_sst *ctx = skl->skl_sst;
-	struct skl_module_cfg *mconfig;
-
-	if (dai->playback_widget->power || dai->capture_widget->power)
-		return 0;
-
-	mconfig = skl_tplg_be_get_cpr_module(dai, substream->stream);
-	if (mconfig == NULL)
-		return -EINVAL;
-
-	return skl_dsp_set_dma_control(ctx, mconfig);
-}
-
 static int skl_pcm_prepare(struct snd_pcm_substream *substream,
 		struct snd_soc_dai *dai)
 {
-- 
2.5.0

[PATCH v2 08/13] ASoC: Intel: Skylake: Add supply widget as non DSP widget

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Supply widgets to model clock supplies for SSP and add this widget type
dapm supply widget as non DSP widget to bypass while parsing the source
and sink dapm widget list.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-topology.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/sound/soc/intel/skylake/skl-topology.c b/sound/soc/intel/skylake/skl-topology.c
index 9cf8c51..edd0c60 100644
--- a/sound/soc/intel/skylake/skl-topology.c
+++ b/sound/soc/intel/skylake/skl-topology.c
@@ -87,6 +87,7 @@ static int is_skl_dsp_widget_type(struct snd_soc_dapm_widget *w)
 	case snd_soc_dapm_aif_out:
 	case snd_soc_dapm_dai_out:
 	case snd_soc_dapm_switch:
+	case snd_soc_dapm_supply:
 		return false;
 	default:
 		return true;
@@ -1484,12 +1485,13 @@ static int skl_tplg_be_set_src_pipe_params(struct snd_soc_dai *dai,
 	snd_soc_dapm_widget_for_each_source_path(w, p) {
 		if (p->connect && is_skl_dsp_widget_type(p->source) &&
 						p->source->priv) {
-
 			ret = skl_tplg_be_fill_pipe_params(dai,
 						p->source->priv, params);
 			if (ret < 0)
 				return ret;
 		} else {
+			if (p->source->id == snd_soc_dapm_supply)
+				continue;
 			ret = skl_tplg_be_set_src_pipe_params(dai,
 						p->source, params);
 			if (ret < 0)
@@ -1515,6 +1517,8 @@ static int skl_tplg_be_set_sink_pipe_params(struct snd_soc_dai *dai,
 			if (ret < 0)
 				return ret;
 		} else {
+			if (p->sink->id == snd_soc_dapm_supply)
+				continue;
 			ret = skl_tplg_be_set_sink_pipe_params(
 						dai, p->sink, params);
 			if (ret < 0)
-- 
2.5.0

[PATCH v2 09/13] ASoC: Intel: Skylake: Add supply widget in skl_nau_max machine

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Maxim codec needs clock to be configured before the SSP startup, so we
need to model the MLCK from SSP0 and turn it on before SSP port is
enabled, so model this in DSP widget parsing.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/boards/skl_nau88l25_max98357a.c | 34 +++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/sound/soc/intel/boards/skl_nau88l25_max98357a.c b/sound/soc/intel/boards/skl_nau88l25_max98357a.c
index 25db5be..06abdf1 100644
--- a/sound/soc/intel/boards/skl_nau88l25_max98357a.c
+++ b/sound/soc/intel/boards/skl_nau88l25_max98357a.c
@@ -100,6 +100,36 @@ static int platform_clock_control(struct snd_soc_dapm_widget *w,
 	return ret;
 }
 
+static struct snd_soc_dai *skl_get_dai_widget(struct snd_soc_dapm_widget *w)
+{
+	struct snd_soc_dapm_path *p = NULL;
+
+	snd_soc_dapm_widget_for_each_sink_path(w, p) {
+		if (p->sink->id == snd_soc_dapm_dai_in)
+			return p->sink->priv;
+
+		return skl_get_dai_widget(p->sink);
+	}
+
+	return NULL;
+}
+
+static int ssp_set_clk(struct snd_soc_dapm_widget *w,
+		struct snd_kcontrol *k, int  event)
+{
+	struct snd_soc_dai *cpu_dai = NULL;
+
+	cpu_dai = skl_get_dai_widget(w);
+	if (!cpu_dai)
+		return -EIO;
+
+	/* Enable/Disable the SSP clk */
+	if (SND_SOC_DAPM_EVENT_ON(event))
+		return snd_soc_dai_set_tristate(cpu_dai, 0);
+	else
+		return snd_soc_dai_set_tristate(cpu_dai, 1);
+}
+
 static const struct snd_kcontrol_new skylake_controls[] = {
 	SOC_DAPM_PIN_SWITCH("Headphone Jack"),
 	SOC_DAPM_PIN_SWITCH("Headset Mic"),
@@ -113,6 +143,9 @@ static const struct snd_soc_dapm_widget skylake_widgets[] = {
 	SND_SOC_DAPM_MIC("SoC DMIC", NULL),
 	SND_SOC_DAPM_SPK("DP", NULL),
 	SND_SOC_DAPM_SPK("HDMI", NULL),
+	SND_SOC_DAPM_SUPPLY("ssp0 mclk", SND_SOC_NOPM, 0, 0,
+			ssp_set_clk, SND_SOC_DAPM_PRE_PMU |
+			SND_SOC_DAPM_POST_PMD),
 	SND_SOC_DAPM_SUPPLY("Platform Clock", SND_SOC_NOPM, 0, 0,
 			platform_clock_control, SND_SOC_DAPM_PRE_PMU |
 			SND_SOC_DAPM_POST_PMD),
@@ -136,6 +169,7 @@ static const struct snd_soc_dapm_route skylake_map[] = {
 	/* CODEC BE connections */
 	{ "HiFi Playback", NULL, "ssp0 Tx" },
 	{ "ssp0 Tx", NULL, "codec0_out" },
+	{ "codec0_out", NULL, "ssp0 mclk"},
 
 	{ "Playback", NULL, "ssp1 Tx" },
 	{ "ssp1 Tx", NULL, "codec1_out" },
-- 
2.5.0

[PATCH v2 10/13] ASoC: Intel: Skylake: Add supply widget in bxt_da_max machine

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Maxim codec needs clock to be configured before the SSP startup, so we
need to model the MLCK from SSP5 and turn it on before SSP port is
enabled, so model this in DSP widget parsing.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/boards/bxt_da7219_max98357a.c | 34 +++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/sound/soc/intel/boards/bxt_da7219_max98357a.c b/sound/soc/intel/boards/bxt_da7219_max98357a.c
index bff80b4..c702967 100644
--- a/sound/soc/intel/boards/bxt_da7219_max98357a.c
+++ b/sound/soc/intel/boards/bxt_da7219_max98357a.c
@@ -43,6 +43,36 @@ enum {
 	BXT_DPCM_AUDIO_HDMI3_PB,
 };
 
+static struct snd_soc_dai *skl_get_dai_widget(struct snd_soc_dapm_widget *w)
+{
+	struct snd_soc_dapm_path *p = NULL;
+
+	snd_soc_dapm_widget_for_each_sink_path(w, p) {
+		if (p->sink->id == snd_soc_dapm_dai_in)
+			return p->sink->priv;
+
+		return skl_get_dai_widget(p->sink);
+	}
+
+	return NULL;
+}
+
+static int ssp_set_clk(struct snd_soc_dapm_widget *w,
+		struct snd_kcontrol *k, int  event)
+{
+	struct snd_soc_dai *cpu_dai = NULL;
+
+	cpu_dai = skl_get_dai_widget(w);
+	if (!cpu_dai)
+		return -EIO;
+
+	/* Enable/Disable the SSP clk */
+	if (SND_SOC_DAPM_EVENT_ON(event))
+		return snd_soc_dai_set_tristate(cpu_dai, 0);
+	else
+		return snd_soc_dai_set_tristate(cpu_dai, 1);
+}
+
 static const struct snd_kcontrol_new broxton_controls[] = {
 	SOC_DAPM_PIN_SWITCH("Headphone Jack"),
 	SOC_DAPM_PIN_SWITCH("Headset Mic"),
@@ -57,6 +87,9 @@ static const struct snd_soc_dapm_widget broxton_widgets[] = {
 	SND_SOC_DAPM_SPK("HDMI1", NULL),
 	SND_SOC_DAPM_SPK("HDMI2", NULL),
 	SND_SOC_DAPM_SPK("HDMI3", NULL),
+	SND_SOC_DAPM_SUPPLY("ssp5 mclk", SND_SOC_NOPM, 0, 0,
+			ssp_set_clk, SND_SOC_DAPM_PRE_PMU |
+			SND_SOC_DAPM_POST_PMD),
 };
 
 static const struct snd_soc_dapm_route broxton_map[] = {
@@ -76,6 +109,7 @@ static const struct snd_soc_dapm_route broxton_map[] = {
 	/* CODEC BE connections */
 	{"HiFi Playback", NULL, "ssp5 Tx"},
 	{"ssp5 Tx", NULL, "codec0_out"},
+	{ "codec0_out", NULL, "ssp5 mclk"},
 
 	{"Playback", NULL, "ssp1 Tx"},
 	{"ssp1 Tx", NULL, "codec1_out"},
-- 
2.5.0

[PATCH v2 11/13] ASoC: Intel: Skylake: Don't reset pass-through pipe in BE prepare

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

When pipe is pass-through, BE and FE modules are defined inside
a pipe, reset of pipe will be done in FE DAI prepare. So don't
reset in the BE prepare.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 688d6f7..800fdad 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -582,8 +582,8 @@ static int skl_link_pcm_prepare(struct snd_pcm_substream *substream,
 
 	/* In case of XRUN recovery, reset the FW pipe to clean state */
 	mconfig = skl_tplg_be_get_cpr_module(dai, substream->stream);
-	if (mconfig && (substream->runtime->status->state ==
-					SNDRV_PCM_STATE_XRUN))
+	if (mconfig && !mconfig->pipe->passthru &&
+		(substream->runtime->status->state == SNDRV_PCM_STATE_XRUN))
 		skl_reset_pipe(skl->skl_sst, mconfig->pipe);
 
 	return 0;
-- 
2.5.0

[PATCH v2 12/13] ASoC: Intel: Skylake: set the resume point to LPIB

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

In system suspend, the firmware pipelines will be deleted and there
is no need to save the pipeline context. Driver will save the DPIB and
LPIB pointers in suspend.

In system resume, the firmware pipelines will be created again and the
RD/RW pointers in the Firmware buffer points to the base address. So
need to fetch the non-played data again to firmware buffer. LPIB
indicates the HW rendered position.

Instead of setting DPIB as resume point, set it to LPIB to restore from
the HW render position so that DMA would fetch the non-played data one
more time.

Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/intel/skylake/skl-pcm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/soc/intel/skylake/skl-pcm.c b/sound/soc/intel/skylake/skl-pcm.c
index 800fdad..508144b 100644
--- a/sound/soc/intel/skylake/skl-pcm.c
+++ b/sound/soc/intel/skylake/skl-pcm.c
@@ -484,7 +484,7 @@ static int skl_pcm_trigger(struct snd_pcm_substream *substream, int cmd,
 			snd_hdac_ext_stream_drsm_enable(ebus, true,
 						hdac_stream(stream)->index);
 			snd_hdac_ext_stream_set_dpibr(ebus, stream,
-							stream->dpib);
+							stream->lpib);
 			snd_hdac_ext_stream_set_lpib(stream, stream->lpib);
 		}
 
-- 
2.5.0

[PATCH v2 13/13] ASoC: hdac_hdmi: Enable pin and converter in prepare

[jeeja.kp]

From: Jeeja KP <jeeja.kp@intel.com>

Instead of enabling pin and cvt in pcm_open(), need to restore pin and
cvt state after system resume to restart the playback which is
paused/stopped before system suspend.
So enable pin and cvt in playback_prepare and call prepare when trigger
cmd is paused/started and resume to reconfigure pin and cvt.

Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
---
 sound/soc/codecs/hdac_hdmi.c | 28 +++++++++++++++++-----------
 1 file changed, 17 insertions(+), 11 deletions(-)

diff --git a/sound/soc/codecs/hdac_hdmi.c b/sound/soc/codecs/hdac_hdmi.c
index c602c49..8d47505 100644
--- a/sound/soc/codecs/hdac_hdmi.c
+++ b/sound/soc/codecs/hdac_hdmi.c
@@ -114,6 +114,12 @@ struct hdac_hdmi_priv {
 	struct hdac_chmap chmap;
 };
 
+static void hdac_hdmi_enable_cvt(struct hdac_ext_device *edev,
+			struct hdac_hdmi_dai_pin_map *dai_map);
+
+static int hdac_hdmi_enable_pin(struct hdac_ext_device *hdac,
+			struct hdac_hdmi_dai_pin_map *dai_map);
+
 static struct hdac_hdmi_pcm *get_hdmi_pcm_from_id(struct hdac_hdmi_priv *hdmi,
 						int pcm_idx)
 {
@@ -411,6 +417,10 @@ static int hdac_hdmi_playback_prepare(struct snd_pcm_substream *substream,
 	dev_dbg(&hdac->hdac.dev, "stream tag from cpu dai %d format in cvt 0x%x\n",
 			dd->stream_tag,	dd->format);
 
+	hdac_hdmi_enable_cvt(hdac, dai_map);
+	ret = hdac_hdmi_enable_pin(hdac, dai_map);
+	if (ret < 0)
+		return ret;
 	mutex_lock(&pin->lock);
 	pin->channels = substream->runtime->channels;
 
@@ -622,11 +632,6 @@ static int hdac_hdmi_pcm_open(struct snd_pcm_substream *substream,
 
 	dai_map->pin = pin;
 
-	hdac_hdmi_enable_cvt(hdac, dai_map);
-	ret = hdac_hdmi_enable_pin(hdac, dai_map);
-	if (ret < 0)
-		return ret;
-
 	ret = hdac_hdmi_eld_limit_formats(substream->runtime,
 				pin->eld.eld_buffer);
 	if (ret < 0)
@@ -642,15 +647,16 @@ static int hdac_hdmi_trigger(struct snd_pcm_substream *substream, int cmd,
 	struct hdac_hdmi_dai_pin_map *dai_map;
 	struct hdac_ext_device *hdac = snd_soc_dai_get_drvdata(dai);
 	struct hdac_hdmi_priv *hdmi = hdac->private_data;
-	int ret;
 
 	dai_map = &hdmi->dai_map[dai->id];
-	if (cmd == SNDRV_PCM_TRIGGER_RESUME) {
-		ret = hdac_hdmi_enable_pin(hdac, dai_map);
-		if (ret < 0)
-			return ret;
-
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_RESUME:
+	case SNDRV_PCM_TRIGGER_START:
+	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
 		return hdac_hdmi_playback_prepare(substream, dai);
+
+	default:
+		return 0;
 	}
 
 	return 0;
-- 
2.5.0