From: jeeja.kp@intel.com
To: alsa-devel@alsa-project.org
Cc: tiwai@suse.de, patches.audio@intel.com, broonie@kernel.org,
liam.r.girdwood@intel.com, Jeeja KP <jeeja.kp@intel.com>
Subject: [PATCH v4 0/9] ASoC: Intel: Skylake: Driver updates
Date: Mon, 2 Jan 2017 12:44:27 +0530 [thread overview]
Message-ID: <1483341277-14475-1-git-send-email-jeeja.kp@intel.com> (raw)
From: Jeeja KP <jeeja.kp@intel.com>
This patch series includes driver updates for the handling scenarios
during System S0/S3 transitions when audio stream is stopped during
system.
o move DMA configuration in DSP Gateway Module widget event handler to
ensure DMA is configured after resume.
o Enable SSP MLCK using Supply widget. This will ensure the MCLK is
enabled when the widget is power on.
o Check DMA decouple register state before coupling/decoupling the DMA.
o In case of HDMI pass-through pipe, reset only the FE Pipe when stream
in in XRUN state.
o Resume the stream from HW renderer position.
o HDMI Codec pin and converter state need to be restored when stream
is resumed.
Changes in v2:
- Addressed Mark's comment on patch 1, split this into 2 as this had
additional changes other than configuring the DMA.
- Addressed Takashi's comment on the usage of snd_hdac_updatel()
Changes in v3:
- Addressed Takashi's comment on superfluous shift used in reading the
value of PPCTL register and also cleaned the condition for updating
the reg value.
Changes in v4:
- Acked by Takashi for patch "ALSA: hda: check stream decoupled register
state".
- Removed compilation warning in patch "ASoC: hdac_hdmi: Enable pin and
converter in prepare".
- Remove 4 patches which are already applied.
Jeeja KP (9):
ALSA: hda: check stream decoupled register state
ASoC: Intel: Skylake: Add set_tristate DAI ops to enable SSP MCLK
ASoC: Intel: Skylake: Remove unused SSP BE prepare DAI ops
ASoC: Intel: Skylake: Add supply widget as non DSP widget
ASoC: Intel: Skylake: Add supply widget in skl_nau_max machine
ASoC: Intel: Skylake: Add supply widget in bxt_da_max machine
ASoC: Intel: Skylake: Don't reset pass-through pipe in BE prepare
ASoC: Intel: Skylake: set the resume point to LPIB
ASoC: hdac_hdmi: Enable pin and converter in prepare
sound/hda/ext/hdac_ext_stream.c | 15 ++++---
sound/soc/codecs/hdac_hdmi.c | 37 ++++++++----------
sound/soc/intel/boards/bxt_da7219_max98357a.c | 34 ++++++++++++++++
sound/soc/intel/boards/skl_nau88l25_max98357a.c | 34 ++++++++++++++++
sound/soc/intel/skylake/skl-pcm.c | 52 +++++++++++++++----------
sound/soc/intel/skylake/skl-topology.c | 6 ++-
6 files changed, 130 insertions(+), 48 deletions(-)
--
2.5.0
next reply other threads:[~2017-01-02 7:03 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-02 7:14 jeeja.kp [this message]
2017-01-02 7:14 ` [PATCH v4 1/9] ALSA: hda: check stream decoupled register state jeeja.kp
2017-01-02 7:14 ` [PATCH v4 2/9] ASoC: Intel: Skylake: Add set_tristate DAI ops to enable SSP MCLK jeeja.kp
2017-01-06 18:32 ` Mark Brown
2017-01-10 9:31 ` Jeeja KP
2017-01-02 7:14 ` [PATCH v4 3/9] ASoC: Intel: Skylake: Remove unused SSP BE prepare DAI ops jeeja.kp
2017-01-02 7:14 ` [PATCH v4 4/9] ASoC: Intel: Skylake: Add supply widget as non DSP widget jeeja.kp
2017-01-02 7:14 ` [PATCH v4 5/9] ASoC: Intel: Skylake: Add supply widget in skl_nau_max machine jeeja.kp
2017-01-02 7:14 ` [PATCH v4 6/9] ASoC: Intel: Skylake: Add supply widget in bxt_da_max machine jeeja.kp
2017-01-06 18:34 ` Mark Brown
2017-01-02 7:14 ` [PATCH v4 7/9] ASoC: Intel: Skylake: Don't reset pass-through pipe in BE prepare jeeja.kp
2017-01-02 7:14 ` [PATCH v4 8/9] ASoC: Intel: Skylake: set the resume point to LPIB jeeja.kp
2017-01-02 7:14 ` [PATCH v4 9/9] ASoC: hdac_hdmi: Enable pin and converter in prepare jeeja.kp
2017-01-19 18:03 ` Applied "ASoC: hdac_hdmi: Enable pin and converter in prepare" to the asoc tree Mark Brown
2017-01-02 10:01 ` [PATCH v4 0/9] ASoC: Intel: Skylake: Driver updates Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1483341277-14475-1-git-send-email-jeeja.kp@intel.com \
--to=jeeja.kp@intel.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=liam.r.girdwood@intel.com \
--cc=patches.audio@intel.com \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).