From: Daniel Mack <daniel@caiaq.de>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org, Timur Tabi <timur@freescale.com>,
Liam Girdwood <lrg@slimlogic.co.uk>
Subject: Re: [PATCH] ALSA: ASoc: Add regulator support to CS4270 codec driver
Date: Thu, 26 Nov 2009 18:42:45 +0100 [thread overview]
Message-ID: <20091126174245.GJ14091@buzzloop.caiaq.de> (raw)
In-Reply-To: <20091126160351.GB10674@rakim.wolfsonmicro.main>
On Thu, Nov 26, 2009 at 04:03:51PM +0000, Mark Brown wrote:
> On Thu, Nov 26, 2009 at 04:48:07PM +0100, Daniel Mack wrote:
>
> > - I only added VA for now because when VD is disabled, we need to
> > restore all codec information, and I can't test that here. We can
> > still add that later, right?
>
> I'd suggest just adding it blind. The code is very simple and it's much
> easier to fix if there's a problem than it is to go through retrofit the
> additional regulator hookups to boards if the other supplies are added
> later.
>
> You can test the flow by defining a fixed voltage regulator with no soft
> control, obviously it won't actually turn the power on or off but the
> code will run.
Ok. I couldn't find a dummy framework for such cases, and registering a
full regulator just to satisfy the codec code seems a litte cumbersome.
Is there anything like that? Or should there be?
> Just fail if you can't get the supply. If you can't get the regulator
> then you've no analogue supply and the CODEC isn't going to work
> terribly well. Currently the assumption is that if you've built in the
> regulator API you intend to use it, otherwise it's very hard to tell if
> the operation failed and broke something or failed because the API isn't
> in use.
Hmm - that will break all existing platforms that use this codec and
need regulators for other drivers. But ok, I'm fine with forcing
everyone to innovation :)
> > struct cs4270_private *cs4270 = i2c_get_clientdata(client);
> > struct snd_soc_codec *codec = &cs4270->codec;
> >
> > + cs4270_set_bias_level(codec, SND_SOC_BIAS_OFF);
> > +
> > return snd_soc_suspend_device(codec->dev);
> > }
>
> This patch isn't against current for-2.6.33 - those functions have been
> removed. Better to do the bias management in the ASoC suspend/resume
> callbacks anyway so that it's joined up with the register save/restore.
> Until we get the pm_link stuff in the next merge window there's no link
> between the I2C bus suspend and the platform bus suspend for the ASoC
> core.
Ok, done - see the new patch below. I did use the regulator_bulk
functions in the first place, but due to the VA special case, I had to
extract the single regulators again from the bulk struct which turned
out to mess the code quite a bit. Looks better this way.
Thanks,
Daniel
>From dedbbb7ee101f635e9682559d31e48b4c57722a3 Mon Sep 17 00:00:00 2001
From: Daniel Mack <daniel@caiaq.de>
Date: Wed, 25 Nov 2009 15:31:25 +0100
Subject: [PATCH] ALSA: ASoc: Add regulator support to CS4270 codec driver
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
---
sound/soc/codecs/cs4270.c | 90 +++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 90 insertions(+), 0 deletions(-)
diff --git a/sound/soc/codecs/cs4270.c b/sound/soc/codecs/cs4270.c
index 8069023..e79d30d 100644
--- a/sound/soc/codecs/cs4270.c
+++ b/sound/soc/codecs/cs4270.c
@@ -28,6 +28,7 @@
#include <sound/initval.h>
#include <linux/i2c.h>
#include <linux/delay.h>
+#include <linux/regulator/consumer.h>
#include "cs4270.h"
@@ -114,6 +115,11 @@ struct cs4270_private {
unsigned int mode; /* The mode (I2S or left-justified) */
unsigned int slave_mode;
unsigned int manual_mute;
+
+ /* power domain regulators (optional) */
+ struct regulator *va_reg;
+ struct regulator *vd_reg;
+ struct regulator *vlc_reg;
};
/**
@@ -458,6 +464,56 @@ static int cs4270_hw_params(struct snd_pcm_substream *substream,
}
/**
+ * cs4270_set_bias_level - catches BIAS level changes
+ * @dai: the SOC DAI
+ * @level: the new BIAS level
+ *
+ * This function controls the voltage regulators to properly
+ * power up/down the voltage regulator domains
+ */
+
+static int cs4270_set_bias_level(struct snd_soc_codec *codec,
+ enum snd_soc_bias_level level)
+{
+ int ret;
+ struct cs4270_private *cs4270 = codec->private_data;
+
+ switch (level) {
+ case SND_SOC_BIAS_ON:
+ ret = regulator_enable(cs4270->vd_reg);
+ if (ret < 0)
+ return ret;
+
+ ret = regulator_enable(cs4270->vlc_reg);
+ if (ret < 0)
+ return ret;
+ /* fall thru */
+ case SND_SOC_BIAS_PREPARE:
+ ret = regulator_enable(cs4270->va_reg);
+ if (ret < 0)
+ return ret;
+ break;
+ case SND_SOC_BIAS_STANDBY:
+ if (codec->bias_level == SND_SOC_BIAS_OFF) {
+ /* OFF -> STANDBY */
+ ret = regulator_enable(cs4270->va_reg);
+ if (ret < 0)
+ return ret;
+ } else
+ regulator_disable(cs4270->va_reg);
+ break;
+ case SND_SOC_BIAS_OFF:
+ regulator_disable(cs4270->va_reg);
+ regulator_disable(cs4270->vd_reg);
+ regulator_disable(cs4270->vlc_reg);
+ break;
+ }
+
+ codec->bias_level = level;
+ return 0;
+}
+
+/**
* cs4270_dai_mute - enable/disable the CS4270 external mute
* @dai: the SOC DAI
* @mute: 0 = disable mute, 1 = enable mute
@@ -579,6 +635,7 @@ static int cs4270_probe(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct snd_soc_codec *codec = cs4270_codec;
+ struct cs4270_private *cs4270 = codec->private_data;
int ret;
/* Connect the codec to the socdev. snd_soc_new_pcms() needs this. */
@@ -599,6 +656,20 @@ static int cs4270_probe(struct platform_device *pdev)
goto error_free_pcms;
}
+ /* get the power supply regulators */
+ cs4270->va_reg = regulator_get(&pdev->dev, "va");
+ cs4270->vd_reg = regulator_get(&pdev->dev, "vd");
+ cs4270->vlc_reg = regulator_get(&pdev->dev, "vlc");
+
+ if (IS_ERR(cs4270->va_reg) ||
+ IS_ERR(cs4270->vd_reg) ||
+ IS_ERR(cs4270->vlc_reg)) {
+ dev_err(codec->dev, "failed to get supplies %s\n", dev_name(codec->dev));
+ goto error_free_pcms;
+ }
+
+ cs4270_set_bias_level(codec, SND_SOC_BIAS_STANDBY);
+
/* And finally, register the socdev */
ret = snd_soc_init_card(socdev);
if (ret < 0) {
@@ -609,6 +680,10 @@ static int cs4270_probe(struct platform_device *pdev)
return 0;
error_free_pcms:
+ regulator_put(cs4270->va_reg);
+ regulator_put(cs4270->vd_reg);
+ regulator_put(cs4270->vlc_reg);
+
snd_soc_free_pcms(socdev);
return ret;
@@ -623,9 +698,15 @@ error_free_pcms:
static int cs4270_remove(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
+ struct snd_soc_codec *codec = cs4270_codec;
+ struct cs4270_private *cs4270 = codec->private_data;
snd_soc_free_pcms(socdev);
+ regulator_put(cs4270->va_reg);
+ regulator_put(cs4270->vd_reg);
+ regulator_put(cs4270->vlc_reg);
+
return 0;
};
@@ -699,6 +780,8 @@ static int cs4270_i2c_probe(struct i2c_client *i2c_client,
codec->write = cs4270_i2c_write;
codec->reg_cache = cs4270->reg_cache;
codec->reg_cache_size = CS4270_NUMREGS;
+ codec->bias_level = SND_SOC_BIAS_OFF;
+ codec->set_bias_level = cs4270_set_bias_level;
/* The I2C interface is set up, so pre-fill our register cache */
@@ -824,6 +907,8 @@ static int cs4270_soc_suspend(struct platform_device *pdev, pm_message_t mesg)
struct snd_soc_codec *codec = cs4270_codec;
int reg = snd_soc_read(codec, CS4270_PWRCTL) | CS4270_PWRCTL_PDN_ALL;
+ cs4270_set_bias_level(codec, SND_SOC_BIAS_OFF);
+
return snd_soc_write(codec, CS4270_PWRCTL, reg);
}
@@ -833,6 +918,11 @@ static int cs4270_soc_resume(struct platform_device *pdev)
struct i2c_client *i2c_client = codec->control_data;
int reg;
+ cs4270_set_bias_level(codec, SND_SOC_BIAS_STANDBY);
+
+ if (codec->suspend_bias_level == SND_SOC_BIAS_ON)
+ cs4270_set_bias_level(codec, SND_SOC_BIAS_ON);
+
/* In case the device was put to hard reset during sleep, we need to
* wait 500ns here before any I2C communication. */
ndelay(500);
--
1.6.5.2
next prev parent reply other threads:[~2009-11-26 17:42 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-11-25 14:36 [PATCH] ALSA: ASoc: Add regulator support to CS4270 codec driver Daniel Mack
2009-11-25 15:01 ` Mark Brown
2009-11-25 15:20 ` Daniel Mack
2009-11-25 15:38 ` Mark Brown
2009-11-25 15:46 ` Daniel Mack
2009-11-26 15:48 ` Daniel Mack
2009-11-26 16:03 ` Mark Brown
2009-11-26 17:42 ` Daniel Mack [this message]
2009-11-27 11:25 ` Mark Brown
2009-11-27 12:41 ` Daniel Mack
2009-11-27 13:32 ` Mark Brown
2009-11-28 20:23 ` Timur Tabi
2009-11-28 20:31 ` Mark Brown
2009-11-28 22:18 ` Timur Tabi
2009-11-29 0:44 ` Daniel Mack
2009-11-29 4:34 ` Timur Tabi
2009-11-29 8:35 ` Daniel Mack
2009-11-30 10:12 ` Daniel Mack
[not found] ` <5610599F537DD74A8D1F5CC946A7507303478C40@az33exm25.fsl.freescale.net>
2009-11-30 12:01 ` Mark Brown
2009-11-30 12:36 ` Daniel Mack
2009-11-30 15:57 ` Daniel Mack
2009-11-30 16:12 ` Mark Brown
2009-11-30 16:51 ` Daniel Mack
2009-11-30 16:56 ` Daniel Mack
2009-12-04 12:00 ` Daniel Mack
2009-12-04 12:07 ` Mark Brown
2009-12-05 2:54 ` Timur Tabi
2009-12-05 3:51 ` Mark Brown
2009-12-05 17:03 ` Timur Tabi
2009-12-07 13:16 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20091126174245.GJ14091@buzzloop.caiaq.de \
--to=daniel@caiaq.de \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=lrg@slimlogic.co.uk \
--cc=timur@freescale.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox