On Thu, May 31, 2012 at 03:18:01PM +0100, Adam Thomson wrote:
> This patch adds support for the Dialog DA732x audio codec.

A few small things below, very minor and easy to correct though.

> +	{ DA732X_REG_STATUS_EXT		, 0x00 },
> +	{ DA732X_REG_STATUS		, 0x00 },

> +	{ DA732X_REG_MBOX0		, 0x00 },
> +	{ DA732X_REG_MBOX1		, 0x00 },
> +	{ DA732X_REG_MBOX2		, 0x00 },
> +	{ DA732X_REG_MBOX_STATUS	, 0x00 },

> +	{ DA732X_REG_ID			, 0x00 },

> +	{ DA732X_REG_DMA_STATUS		, 0x00 },
> +	{ DA732X_REG_BROWNOUT		, 0x00 },

I would be very surprised if some or all of the above regsters aren't
volatile and therefore shouldn't have default specified.

> +static int da732x_hpf_set(struct snd_kcontrol *kcontrol,
> +			  struct snd_ctl_elem_value *ucontrol)

Why doesn't a standard enum work for this?

> +	/* High Pass Filters */
> +	SOC_ENUM_EXT("DAC1 High Pass Filter Mode Switch",
> +		     da732x_dac1_hpf_mode_enum, da732x_hpf_get, da732x_hpf_set),

This shouldn't be a Switch, it's an enumeration.  Switches are plain
boolean controls.

> +	SOC_SINGLE("ADC1 Equalizer Switch", DA732X_REG_ADC1_EQ5,
> +		   DA732X_EQ_EN_SHIFT, DA732X_EQ_EN_MAX, DA732X_NO_INVERT),
> +	SOC_SINGLE_TLV("ADC1 EQ Band 1 Volume", DA732X_REG_ADC1_EQ12,
> +		       DA732X_EQ_BAND1_SHIFT, DA732X_EQ_VOL_VAL_MAX,
> +		       DA732X_INVERT, eq_band_pga_tlv),

I'd suggest calling the Switch "ADC1 EQ Switch" for consistency with the
gains for the bands (or expanding EQ in the gains but that'll make for a
lot of really long control names).

> +	case SND_SOC_DAPM_POST_PMU:
> +		if (w->reg == DA732X_REG_ADC1_PD)
> +			snd_soc_update_bits(codec, DA732X_REG_CLK_EN3,
> +					    DA732X_ADCA_BB_CLK_EN,
> +					    DA732X_ADCA_BB_CLK_EN);
> +		else
> +			snd_soc_update_bits(codec, DA732X_REG_CLK_EN3,
> +					    DA732X_ADCC_BB_CLK_EN,
> +					    DA732X_ADCC_BB_CLK_EN);

This reads like it should be a switch statement.  The effect will be the
same but it's a bit clearer.

> +	da732x->regmap = devm_regmap_init_i2c(i2c, &da732x_regmap);
> +	if (IS_ERR(da732x->regmap)) {
> +		ret = PTR_ERR(da732x->regmap);
> +		dev_err(&i2c->dev, "Failed to initialize regmap\n");
> +		goto err;
> +	}
> +
> +	ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_da732x,
> +				     da732x_dai, ARRAY_SIZE(da732x_dai));

The register cache defaults make it look like there's a device ID
(or possibly chip revision?) register - it'd be good practice to read it
here and either verify that it has the expected value or log it
depending on which it is.

> +static const struct i2c_device_id da732x_i2c_id[] = {
> +	{ "da732x", 0},
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(i2c, da732x_i2c_id);

Good practice would be to enumerate all the device IDs (so users can
just register devices) but it doesn't really matter.