Re: Intel SST on a Bay Trail tablet

[Vinod Koul <vinod.koul@intel.com>]

On Wed, Jun 24, 2015 at 03:46:13PM +0530, Vinod Koul wrote:
> On Tue, Apr 14, 2015 at 05:06:27PM +0300, Jarkko Nikula wrote:
> > My 2c below.
> > 
> > On 04/14/2015 04:02 PM, Antonio Ospite wrote:
> > >On Wed, 4 Mar 2015 17:02:18 +0100
> > >Antonio Ospite <ao2@ao2.it> wrote:
> > 
> > >I realized than I needed to set up the path between the FrontEnd DAI
> > >and the BackEnd one, and in fact the error below goes away and I can
> > >_start_ some playback after switching on these controls:
> > >	codec_out1 mix 0 pcm0_in Switch
> > >	media0_out mix 0 media1_in Switch
> > >which AFAICS constitute the playback path.
> > >
> > >However there is still no sound, and the playback stalls, and the
> > >interrupt count suddenly stops for the intel_sst_driver IRQ
> > >(in /proc/interrupts).
> > >
> > What comes to my mind did you change .acpi_ipc_irq_index = 5 to 0
> > zero in sound/soc/intel/sst/sst_acpi.c: byt_rvp_res_info structure?
> > 
> > According to Teclast's DSDT table the DSP-host interrupt is at first
> > interrupt resource index.
> > 
> > >By looking at /sys/kernel/debug under Android it looks like the
> > >codec is connected to SSP2, and not SSP0 as we imagined before:
> > >/sys/kernel/debug/asoc/baytrailaudio/sst-platform/dapm/ssp2 playback
> > >/sys/kernel/debug/asoc/baytrailaudio/sst-platform/dapm/ssp2 Capture
> > >
> > >So now I'd like to make sure the mixer settings are OK before looking
> > >elsewhere again.
> > >
> > >Vinod, Subhransu, or anyone else, can you share some working alsa state
> > >files for the baytrailcraudio device in linux mainline?
> > >
> > Question to Vinod et all too:
> > 
> > I don't find above "ssp2 playback" and "ssp2 Capture" stream names
> > from sound/soc/intel/sst-mfld-platform-pcm.c so I guess it has been
> > evolved a bit from those original Android drivers.
> The upstream code is subset of one in Android but base stuff is still the
> same
> 
> > 
> > Which makes me thinking how does those strings describe the SSP port
> > setup? E.g. do they reflect what port is actually used or could it
> > be possible that those are just driver strings but firmware could
> > have been tuned for SSP0? If I looked at earlier right, Teclast has
> > the low pin-count Baytrail without SSP2 but I'm not sure about that.
> The FW doesnt provide way to changes ports from driver in this, so this
> doesnt mean much. If we are sure it is not ssp2, I can provide ssp1 fw for
> test
I ahve pushed latest BYT version we have as well as added binary for second
SSP port. Please give it a try:

https://git.kernel.org/cgit/linux/kernel/git/vkoul/firmware.git/commit/?h=byt&id=28ff420dd33ec299217bad7d526ff3bfd163b551

-- 
~Vinod

> > 
> > >JFTR I am running a 64bit kernel, is this OK on BayTrail?
> > >I guess it is, but I just wanted to mention this to be sure.
> > >
> > Generally yes. I've used both 32- and 64-bit kernels when developing
> > the sound/soc/intel/sst-baytrail-* but I haven't tested
> > sound/soc/intel/sst/. Vinod, I guess that should be 64-bit safe too?
> Yup tested on both :)
> 
> -- 
> ~Vinod

--