Hi All

I use device tree add to attachments . Now linux boot but no detect 
sgtl5000 device.
The Linux kernael 3-17 configure from .config file.

Please check my configuration files (kernel , devicetree).
(I set all required device to detect sgtl5000 )

Wojciech Żebrowski
W dniu 2015-06-17 o 16:28, Wojciech Zebrowski pisze:
> Hi Nikolay
>
> Thx for your advice , i try use it in feature dts files.
> My problem is as below , i can send you boot log or , dmesg log if you 
> have any other proposition i can debug it too.
>
> 1.*I use I2C* controler to configure sgtl5000 :
>         axi_iic_sgtl: i2c@41610000 {
>             #address-cells = <1>;
>             #size-cells = <0>;
>             compatible = "xlnx,xps-iic-2.00.a";
>             interrupt-parent = <&gic>;
>             interrupts = <0 31 4>;
>             reg = <0x41610000 0x10000>;
>
>             codec: sgtl5000@0a {
>                 #sound-dai-cells = <0>;
>                 compatible = "fsl,sgtl5000";
>                 reg = <0x0a>;
> /*                VDDA-supply = <&reg_3p3v>; */
> /*                VDDIO-supply = <&reg_3p3v>;*/
>                 clocks = <&clkc 19>;
>       };
> *
> **  How can i set comment lines ? *
>
> 2. sound :
>         sound {
>            compatible = "fsl,imx51-babbage-sgtl5000",
> "fsl,imx-audio-sgtl5000";
>            model = "imx51-babbage-sgtl5000";
> /*          ssi-controller = <&ssi1>;  */
>            audio-codec = <&codec>;
>            audio-routing =
>                    "MIC_IN", "Mic Jack",
>                    "Mic Jack", "Mic Bias",
>                    "Headphone Jack", "HP_OUT";
>            mux-int-port = <1>;
>            mux-ext-port = <3>;
>          };/
> *I want use I2C configuration driver not SPI . How can i set comment 
> line ? **
> ***
> 3. I2S driver looks like ok  :
>         axi_i2s_adi_0: axi_i2s_adi@77600000 {
>              compatible = "xlnx,axi-i2s-adi-1.0";
>              reg = <0x77600000 0x10000>;
>              xlnx,bclk-pol = <0x0>;
>              xlnx,dma-type = <0x1>;
>              xlnx,has-rx = <0x1>;
>              xlnx,has-tx = <0x1>;
>              xlnx,lrclk-pol = <0x0>;
>              xlnx,num-ch = <0x1>;
>              xlnx,s-axi-min-size = <0x000001FF>;
>              xlnx,slot-width = <0x18>;
>          };
>
>
>
> W dniu 2015-06-17 o 04:21, Nikolay Dimitrov pisze:
>> Hi Wojciech,
>>
>> On 06/11/2015 09:59 AM, Wojciech Zebrowski wrote:
>>> Hi All
>>>
>>> I try solve problem with support SGTL5000  under Linux , ARM / ZYNQ
>>> ARCHITECTURE. Please add this post to "alsa" forum.  If you need any
>>> others information i can send it .
>>>
>>> My post:
>>>
>>>   I try use freescale audio chip sgtl5000 on my custom board with Zynq
>>> chip. I need help with instance driver in device tree and debug first
>>> execution.
>>>
>>> 1.*I use I2C* controler to configure sgtl5000 :
>>> /        axi_iic_sgtl: i2c@41610000 {//
>>> //            #address-cells = <1>;//
>>> //            #size-cells = <0>;//
>>> //            compatible = "xlnx,xps-iic-2.00.a";//
>>> //            interrupt-parent = <&gic>;//
>>> //            interrupts = <0 31 4>;//
>>> //            reg = <0x41610000 0x10000>;//
>>> ////
>>> //            codec: sgtl5000@0a {//
>>> //                #sound-dai-cells = <0>;//
>>> //                compatible = "fsl,sgtl5000";//
>>> //                reg = <0x0a>;//
>>> //////                VDDA-supply = <&reg_3p3v>;//
>>> //////                VDDIO-supply = <&reg_3p3v>;//
>>> //                clocks = <&clkc 19>;//
>>> //      }; /
>>>
>>>   How can i set comment lines ?
>>>
>>> 2. sound :
>>> /        sound {
>>>            compatible = "fsl,imx51-babbage-sgtl5000",
>>> "fsl,imx-audio-sgtl5000";
>>>            model = "imx51-babbage-sgtl5000";
>>> //          ssi-controller = <&ssi1>;
>>>            audio-codec = <&codec>;
>>>            audio-routing =
>>>                    "MIC_IN", "Mic Jack",
>>>                    "Mic Jack", "Mic Bias",
>>>                    "Headphone Jack", "HP_OUT";
>>>            mux-int-port = <1>;
>>>            mux-ext-port = <3>;
>>>          };/
>>> I want use I2C configuration driver not SPI . How can i set comment 
>>> line ?
>>>
>>> 3. I2S driver looks like ok  :
>>> /        axi_i2s_adi_0: axi_i2s_adi@77600000 {
>>>              compatible = "xlnx,axi-i2s-adi-1.0";
>>>              reg = <0x77600000 0x10000>;
>>>              xlnx,bclk-pol = <0x0>;
>>>              xlnx,dma-type = <0x1>;
>>>              xlnx,has-rx = <0x1>;
>>>              xlnx,has-tx = <0x1>;
>>>              xlnx,lrclk-pol = <0x0>;
>>>              xlnx,num-ch = <0x1>;
>>>              xlnx,s-axi-min-size = <0x000001FF>;
>>>              xlnx,slot-width = <0x18>;
>>>          };/
>>>
>>>
>>> PS.
>>> Right now i can compile device tree but audio is not detected.
>>> What kind of log do you need to check Linux boot problem ?
>>
>> Comments in DTS files are done the old-school C way, /* */.
> Changed
>>
>> Regarding the SGTL5K configuration, please take a look here for
>> reference:
>>
>> https://github.com/torvalds/linux/blob/0f57d86787d8b1076ea8f9cbdddda2a46d534a27/arch/arm/boot/dts/imx6dl-riotboard.dts 
>>
>>
> I thing it is the same as my .
>> If the audio codec device is detected during boot, you should see
>> something like this in you boot logs:
>>
>>
>> ...
>> sgtl5000 0-000a: sgtl5000 revision 0x11
>> sgtl5000 0-000a: Using internal LDO instead of VDDD
>> imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
>> ...
> Nothing
>> ALSA device list:
>> #0: imx6-riotboard-sgtl5000
>> ...
> Nothing
>>
>>
>> Regards,
>> Nikolay
>>
>