Re: module snd-atiixp issue with suspend/hibernate/resume

[Takashi Iwai <tiwai@suse.de>]

At Thu, 30 Apr 2009 00:43:02 -0400,
Ryan Dunn wrote:
> 
> Thanks Lee,
> 
> I grabbed the kernel source from the repos and started perusing the code.  It
> looks like when the module is installed, the call chain starts in atiixp.c and
> moves into ac97/ac97_codec.c via a call to snd_ac97_tune_hardware() which
> ultimately twiddles a bit in the AC97_POWERDOWN register.  I'm not sure yet if
> the suspend method properly saves this register on suspend or not;

It should.  snd_ac97_resume() writes the cached value.
Check /proc/asound/card0/codec97#0/ac97#*+regs files before and after
suspend.  You can change the codec register value directly via proc
file, e.g.
    # echo 0x12 0x1234 > /proc/asound/card0/codec97#0/ac97#0-0+regs
(only when you build with the debug option).

The bit 0x8000 of the power-down register should correspond to LED.


Takashi

> or if the
> same call chain needs to be repeated on a resume.  I appreciate your quick and
> relevant answer.  When I get time, I'll start adding some debug printouts to
> try this out.
> 
> Also, the struct ac97_quirk ac97_quirks[] array has a couple of entries in it
> currently (in the atiixp.c file).  How do I get the subvender/subdevice id's
> for my system (I didn't seem to have luck with lspci, unless I'm not looking
> in the right fields)?  Would it be possible to edit the driver so that an
> explict module option would not be needed on my hardware?
> 
> Thanks,
> Ryan
> 
> On Wed, Apr 29, 2009 at 10:42 PM, Lee Revell <rlrevell@joe-job.com> wrote:
> 
>     On Wed, Apr 29, 2009 at 12:06 AM, Ryan Dunn <oryandunn.ml@gmail.com>
>     wrote:
>     > I have a Compaq V2000 laptop with the ATI IXP chipset and make use of
>     the
>     > snd-atiixp module.  The laptop needs to have the ac97_quirk option set
>     to 7
>     > to enable the mute LED.  After setting this option in the
>     > /etc/modprobe.d/options.conf file, the mute LED works after a reboot.
>     > However, after a resume from suspend or hibernate, the mute LED does not
>     > work.  The alsa-info.sh script reports that the quirk is still set with
>     7.
>     > At this point a reboot will NOT fix the problem.  The only way to fix it
>     is
>     > to remove and reinsert the module with modprobe.
>     >
>     > This is on a fresh Ubuntu 9.04 install.  Any ideas?  I wasn't sure if
>     this
>     > should be reported here or on the kernel list.  I saw a similar issue
>     with
>     > the ac97_quirk on the kernel list and they were referred here.  I'm a
>     > software developer, so I'd be willing to try ideas/possible solutions if
>     you
>     > have them.
>    
>     Get the Ubuntu source code for the package that owns that ALSA driver,
>     find the place in the driver's initialization code where ac97_quirk=7
>     is handled, then check the driver's suspend and resume callbacks and
>     make sure the suspend callback is correctly saving the LED state and
>     that the resume callback is re-initializing the LED from the saved
>     state in the same way the init code does.  grep and printk() are your
>     friends ;-)
>    
>     HTH,
>    
>     Lee
> 
>