From: greearb@candelatech.com
To: ath10k@lists.infradead.org
Cc: Ben Greear <greearb@candelatech.com>, linux-wireless@vger.kernel.org
Subject: [PATCH 2/2] ath10k: support get/set antenna configurations.
Date: Wed, 7 May 2014 14:50:40 -0700 [thread overview]
Message-ID: <1399499440-32365-2-git-send-email-greearb@candelatech.com> (raw)
In-Reply-To: <1399499440-32365-1-git-send-email-greearb@candelatech.com>
From: Ben Greear <greearb@candelatech.com>
Tested with CT firmware, but should work on standard
firmware as well.
Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.
Signed-off-by: Ben Greear <greearb@candelatech.com>
---
drivers/net/wireless/ath/ath10k/core.h | 5 +++
drivers/net/wireless/ath/ath10k/mac.c | 64 ++++++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi.c | 5 +++
3 files changed, 74 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 7050c47..f7eb8050 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -472,6 +472,11 @@ struct ath10k {
u32 dfs_block_radar_events;
int install_key_rv; /* Store error code from key-install */
+ unsigned char supp_tx_chainmask;
+ unsigned char supp_rx_chainmask;
+ unsigned char cfg_tx_chainmask;
+ unsigned char cfg_rx_chainmask;
+
struct wmi_pdev_set_wmm_params_arg wmm_params;
struct completion install_key_done;
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index dcb147d..cc85bd9 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2483,6 +2483,61 @@ void ath10k_halt(struct ath10k *ar)
spin_unlock_bh(&ar->data_lock);
}
+static int ath10k_get_antenna(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant)
+{
+ struct ath10k *ar = hw->priv;
+
+ if (ar->cfg_tx_chainmask) {
+ *tx_ant = ar->cfg_tx_chainmask;
+ *rx_ant = ar->cfg_rx_chainmask;
+ } else {
+ *tx_ant = ar->supp_tx_chainmask;
+ *rx_ant = ar->supp_rx_chainmask;
+ }
+ return 0;
+}
+
+static int __ath10k_set_antenna(struct ath10k *ar, u32 tx_ant, u32 rx_ant)
+{
+ int ret;
+
+ ar->cfg_tx_chainmask = tx_ant;
+ ar->cfg_rx_chainmask = rx_ant;
+
+ if (ar->state != ATH10K_STATE_ON)
+ return 0;
+
+ ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->tx_chain_mask,
+ tx_ant);
+ if (ret) {
+ ath10k_warn("failed to set tx-chainmask: %d, req 0x%x\n",
+ ret, tx_ant);
+ return ret;
+ }
+
+ ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->rx_chain_mask,
+ rx_ant);
+ if (ret) {
+ ath10k_warn("failed to set rx-chainmask: %d, req 0x%x\n",
+ ret, rx_ant);
+ return ret;
+ }
+
+ return ret;
+}
+
+static int ath10k_set_antenna(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant)
+{
+ struct ath10k *ar = hw->priv;
+ int ret;
+
+ mutex_lock(&ar->conf_mutex);
+ ret = __ath10k_set_antenna(ar, tx_ant, rx_ant);
+ mutex_unlock(&ar->conf_mutex);
+ return ret;
+}
+
+
static int ath10k_start(struct ieee80211_hw *hw)
{
struct ath10k *ar = hw->priv;
@@ -2530,6 +2585,10 @@ static int ath10k_start(struct ieee80211_hw *hw)
if (ret)
ath10k_warn("failed to enable dynamic BW: %d\n", ret);
+ if (ar->cfg_tx_chainmask)
+ __ath10k_set_antenna(ar, ar->cfg_tx_chainmask,
+ ar->cfg_rx_chainmask);
+
/*
* By default FW set ARP frames ac to voice (6). In that case ARP
* exchange is not working properly for UAPSD enabled AP. ARP requests
@@ -4437,6 +4496,8 @@ static const struct ieee80211_ops ath10k_ops = {
.set_frag_threshold = ath10k_set_frag_threshold,
.flush = ath10k_flush,
.tx_last_beacon = ath10k_tx_last_beacon,
+ .set_antenna = ath10k_set_antenna,
+ .get_antenna = ath10k_get_antenna,
.restart_complete = ath10k_restart_complete,
.get_survey = ath10k_get_survey,
.set_bitrate_mask = ath10k_set_bitrate_mask,
@@ -4818,6 +4879,9 @@ int ath10k_mac_register(struct ath10k *ar)
BIT(NL80211_IFTYPE_ADHOC) |
BIT(NL80211_IFTYPE_AP);
+ ar->hw->wiphy->available_antennas_rx = ar->supp_rx_chainmask;
+ ar->hw->wiphy->available_antennas_tx = ar->supp_tx_chainmask;
+
if (!test_bit(ATH10K_FW_FEATURE_NO_P2P, ar->fw_features))
ar->hw->wiphy->interface_modes |=
BIT(NL80211_IFTYPE_P2P_CLIENT) |
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 82a827e..d82b740 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -2601,6 +2601,8 @@ static int ath10k_wmi_main_cmd_init(struct ath10k *ar)
config.ast_skid_limit = __cpu_to_le32(TARGET_AST_SKID_LIMIT);
config.tx_chain_mask = __cpu_to_le32(TARGET_TX_CHAIN_MASK);
config.rx_chain_mask = __cpu_to_le32(TARGET_RX_CHAIN_MASK);
+ ar->supp_tx_chainmask = TARGET_TX_CHAIN_MASK;
+ ar->supp_rx_chainmask = TARGET_RX_CHAIN_MASK;
config.rx_timeout_pri_vo = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_be = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI);
@@ -2721,6 +2723,9 @@ static int ath10k_wmi_10x_cmd_init(struct ath10k *ar)
config.num_tids = __cpu_to_le32(TARGET_10X_NUM_TIDS);
config.tx_chain_mask = __cpu_to_le32(TARGET_10X_TX_CHAIN_MASK);
config.rx_chain_mask = __cpu_to_le32(TARGET_10X_RX_CHAIN_MASK);
+ /* TODO: Have to deal with 2x2 chips if/when the come out. */
+ ar->supp_tx_chainmask = TARGET_10X_TX_CHAIN_MASK;
+ ar->supp_rx_chainmask = TARGET_10X_RX_CHAIN_MASK;
config.rx_timeout_pri_vo = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
config.rx_timeout_pri_be = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
--
1.7.11.7
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next prev parent reply other threads:[~2014-05-07 21:51 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-07 21:50 [PATCH 1/2] ath10k: Fix spelling mistake in comments greearb
2014-05-07 21:50 ` greearb [this message]
2014-05-08 5:43 ` [PATCH 2/2] ath10k: support get/set antenna configurations Michal Kazior
2014-05-16 13:47 ` [PATCH 1/2] ath10k: Fix spelling mistake in comments Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1399499440-32365-2-git-send-email-greearb@candelatech.com \
--to=greearb@candelatech.com \
--cc=ath10k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox