ATH10K Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Bob Copeland <me@bobcopeland.com>
To: linux-wireless@vger.kernel.org
Cc: Bob Copeland <me@bobcopeland.com>, ath10k@lists.infradead.org
Subject: [PATCH v3 3/3] ath10k: implement mesh support
Date: Wed,  9 Sep 2015 12:47:36 -0400	[thread overview]
Message-ID: <1441817256-3997-3-git-send-email-me@bobcopeland.com> (raw)
In-Reply-To: <1441817256-3997-1-git-send-email-me@bobcopeland.com>

Add support for mesh to ath10k.  We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.

Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode.  As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true.  The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70-2.

When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:

    ip link set wlan0 down
    iw dev wlan0 set type mp
    ip link set wlan0 up
    iw dev wlan0 set freq 5745 80 5775
    iw dev wlan0 mesh join mesh-vht

Signed-off-by: Bob Copeland <me@bobcopeland.com>
---
v3:
 * fix cfg80211 interface combinations warning when
   CONFIG_MAC80211_MESH=n or when using 10.4 FW (Kalle Valo)
v2:
 * added raw mode feature flag check
 * usage and firmware notes in commit log

 drivers/net/wireless/ath/ath10k/core.c | 12 ++++++++++++
 drivers/net/wireless/ath/ath10k/mac.c  | 36 +++++++++++++++++++++++++++++++++-
 2 files changed, 47 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 6e5033b..09a74a8 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -34,16 +34,19 @@ unsigned int ath10k_debug_mask;
 static unsigned int ath10k_cryptmode_param;
 static bool uart_print;
 static bool skip_otp;
+static bool rawmode;
 
 module_param_named(debug_mask, ath10k_debug_mask, uint, 0644);
 module_param_named(cryptmode, ath10k_cryptmode_param, uint, 0644);
 module_param(uart_print, bool, 0644);
 module_param(skip_otp, bool, 0644);
+module_param(rawmode, bool, 0644);
 
 MODULE_PARM_DESC(debug_mask, "Debugging mask");
 MODULE_PARM_DESC(uart_print, "Uart target debugging");
 MODULE_PARM_DESC(skip_otp, "Skip otp failure for calibration in testmode");
 MODULE_PARM_DESC(cryptmode, "Crypto mode: 0-hardware, 1-software");
+MODULE_PARM_DESC(rawmode, "Use raw 802.11 frame datapath");
 
 static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	{
@@ -1122,6 +1125,15 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
 	ar->htt.max_num_amsdu = ATH10K_HTT_MAX_NUM_AMSDU_DEFAULT;
 	ar->htt.max_num_ampdu = ATH10K_HTT_MAX_NUM_AMPDU_DEFAULT;
 
+	if (rawmode) {
+		if (!test_bit(ATH10K_FW_FEATURE_RAW_MODE_SUPPORT,
+			      ar->fw_features)) {
+			ath10k_err(ar, "rawmode = 1 requires support from firmware");
+			return -EINVAL;
+		}
+		set_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags);
+	}
+
 	if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
 		ar->wmi.rx_decap_mode = ATH10K_HW_TXRX_RAW;
 
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 80efcc8..1cda4f9 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4211,6 +4211,14 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
 	case NL80211_IFTYPE_ADHOC:
 		arvif->vdev_type = WMI_VDEV_TYPE_IBSS;
 		break;
+	case NL80211_IFTYPE_MESH_POINT:
+		if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
+			ret = -EINVAL;
+			ath10k_warn(ar, "must load driver with rawmode=1 to add mesh interfaces\n");
+			goto err;
+		}
+		arvif->vdev_type = WMI_VDEV_TYPE_AP;
+		break;
 	case NL80211_IFTYPE_AP:
 		arvif->vdev_type = WMI_VDEV_TYPE_AP;
 
@@ -4251,6 +4259,7 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
 	 * become corrupted, e.g. have garbled IEs or out-of-date TIM bitmap.
 	 */
 	if (vif->type == NL80211_IFTYPE_ADHOC ||
+	    vif->type == NL80211_IFTYPE_MESH_POINT ||
 	    vif->type == NL80211_IFTYPE_AP) {
 		arvif->beacon_buf = dma_zalloc_coherent(ar->dev,
 							IEEE80211_MAX_FRAME_LEN,
@@ -4590,6 +4599,13 @@ static void ath10k_bss_info_changed(struct ieee80211_hw *hw,
 		if (ret)
 			ath10k_warn(ar, "failed to update beacon template: %d\n",
 				    ret);
+
+		if (ieee80211_vif_is_mesh(vif)) {
+			/* mesh doesn't use SSID but firmware needs it */
+			strncpy(arvif->u.ap.ssid, "mesh",
+				sizeof(arvif->u.ap.ssid));
+			arvif->u.ap.ssid_len = 4;
+		}
 	}
 
 	if (changed & BSS_CHANGED_AP_PROBE_RESP) {
@@ -5329,6 +5345,7 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 	} else if (old_state == IEEE80211_STA_AUTH &&
 		   new_state == IEEE80211_STA_ASSOC &&
 		   (vif->type == NL80211_IFTYPE_AP ||
+		    vif->type == NL80211_IFTYPE_MESH_POINT ||
 		    vif->type == NL80211_IFTYPE_ADHOC)) {
 		/*
 		 * New association.
@@ -5364,6 +5381,7 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 	} else if (old_state == IEEE80211_STA_ASSOC &&
 		    new_state == IEEE80211_STA_AUTH &&
 		    (vif->type == NL80211_IFTYPE_AP ||
+		     vif->type == NL80211_IFTYPE_MESH_POINT ||
 		     vif->type == NL80211_IFTYPE_ADHOC)) {
 		/*
 		 * Disassociation.
@@ -6678,6 +6696,9 @@ static const struct ieee80211_iface_limit ath10k_if_limits[] = {
 	{
 	.max	= 7,
 	.types	= BIT(NL80211_IFTYPE_AP)
+#ifdef CONFIG_MAC80211_MESH
+		| BIT(NL80211_IFTYPE_MESH_POINT)
+#endif
 	},
 };
 
@@ -6685,6 +6706,9 @@ static const struct ieee80211_iface_limit ath10k_10x_if_limits[] = {
 	{
 	.max	= 8,
 	.types	= BIT(NL80211_IFTYPE_AP)
+#ifdef CONFIG_MAC80211_MESH
+		| BIT(NL80211_IFTYPE_MESH_POINT)
+#endif
 	},
 };
 
@@ -6722,6 +6746,9 @@ static const struct ieee80211_iface_limit ath10k_tlv_if_limit[] = {
 	{
 		.max = 2,
 		.types = BIT(NL80211_IFTYPE_AP) |
+#ifdef CONFIG_MAC80211_MESH
+			 BIT(NL80211_IFTYPE_MESH_POINT) |
+#endif
 			 BIT(NL80211_IFTYPE_P2P_CLIENT) |
 			 BIT(NL80211_IFTYPE_P2P_GO),
 	},
@@ -6743,6 +6770,9 @@ static const struct ieee80211_iface_limit ath10k_tlv_qcs_if_limit[] = {
 	{
 		.max = 1,
 		.types = BIT(NL80211_IFTYPE_AP) |
+#ifdef CONFIG_MAC80211_MESH
+			 BIT(NL80211_IFTYPE_MESH_POINT) |
+#endif
 			 BIT(NL80211_IFTYPE_P2P_GO),
 	},
 	{
@@ -6809,6 +6839,9 @@ static const struct ieee80211_iface_limit ath10k_10_4_if_limits[] = {
 	{
 		.max	= 16,
 		.types	= BIT(NL80211_IFTYPE_AP)
+#ifdef CONFIG_MAC80211_MESH
+			| BIT(NL80211_IFTYPE_MESH_POINT)
+#endif
 	},
 };
 
@@ -7033,7 +7066,8 @@ int ath10k_mac_register(struct ath10k *ar)
 
 	ar->hw->wiphy->interface_modes =
 		BIT(NL80211_IFTYPE_STATION) |
-		BIT(NL80211_IFTYPE_AP);
+		BIT(NL80211_IFTYPE_AP) |
+		BIT(NL80211_IFTYPE_MESH_POINT);
 
 	ar->hw->wiphy->available_antennas_rx = ar->supp_rx_chainmask;
 	ar->hw->wiphy->available_antennas_tx = ar->supp_tx_chainmask;
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

  parent reply	other threads:[~2015-09-09 16:48 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-09-09 16:47 [PATCH v3 1/3] ath10k: enable monitor when OTHER_BSS requested Bob Copeland
2015-09-09 16:47 ` [PATCH v3 2/3] ath10k: check for encryption before adding MIC_LEN Bob Copeland
2015-09-09 16:47 ` Bob Copeland [this message]
2015-09-17 10:57 ` [PATCH v3 1/3] ath10k: enable monitor when OTHER_BSS requested Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1441817256-3997-3-git-send-email-me@bobcopeland.com \
    --to=me@bobcopeland.com \
    --cc=ath10k@lists.infradead.org \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox