From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from emh02.mail.saunalahti.fi ([62.142.5.108]) by merlin.infradead.org with esmtps (Exim 4.80.1 #2 (Red Hat Linux)) id 1VWRQL-0000WD-LO for ath10k@lists.infradead.org; Wed, 16 Oct 2013 13:46:06 +0000 Subject: [PATCH v2 1/8] ath10k: prevent starting monitor without a vdev From: Kalle Valo Date: Wed, 16 Oct 2013 16:45:41 +0300 Message-ID: <20131016134541.25095.59430.stgit@localhost6.localdomain6> In-Reply-To: <20131016134503.25095.8044.stgit@localhost6.localdomain6> References: <20131016134503.25095.8044.stgit@localhost6.localdomain6> MIME-Version: 1.0 List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "ath10k" Errors-To: ath10k-bounces+kvalo=adurom.com@lists.infradead.org To: ath10k@lists.infradead.org Cc: linux-wireless@vger.kernel.org From: Michal Kazior This fixes issue with interface bridging. Linux bridging sets promiscuous mode for all interfaces that are in a bridge. This translates to configure_filter() being called in a mac80211 driver. Before the patch operational interface would be started and upped again when promiscuous mode was enabled causing all sorts of strange issues: * no HTT RX happening (i.e. no traffic) * FW crash upon driver reload/unload Signed-off-by: Michal Kazior Signed-off-by: Kalle Valo --- drivers/net/wireless/ath/ath10k/mac.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index 0b1cc51..527343d 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -2265,8 +2265,14 @@ static void ath10k_configure_filter(struct ieee80211_hw *hw, *total_flags &= SUPPORTED_FILTERS; ar->filter_flags = *total_flags; + /* Monitor must not be started if it wasn't created first. + * Promiscuous mode may be started on a non-monitor interface - in + * such case the monitor vdev is not created so starting the + * monitor makes no sense. Since ath10k uses no special RX filters + * (only BSS filter in STA mode) there's no need for any special + * action here. */ if ((ar->filter_flags & FIF_PROMISC_IN_BSS) && - !ar->monitor_enabled) { + !ar->monitor_enabled && ar->monitor_present) { ath10k_dbg(ATH10K_DBG_MAC, "mac monitor %d start\n", ar->monitor_vdev_id); @@ -2274,7 +2280,7 @@ static void ath10k_configure_filter(struct ieee80211_hw *hw, if (ret) ath10k_warn("Unable to start monitor mode\n"); } else if (!(ar->filter_flags & FIF_PROMISC_IN_BSS) && - ar->monitor_enabled) { + ar->monitor_enabled && ar->monitor_present) { ath10k_dbg(ATH10K_DBG_MAC, "mac monitor %d stop\n", ar->monitor_vdev_id); _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k