ATH10K Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Christian Lamparter <chunkeey@googlemail.com>
To: David Hutchison <dhutchison@bluemesh.net>
Cc: OpenWrt Development List <openwrt-devel@lists.openwrt.org>,
	ath10k@lists.infradead.org
Subject: Re: [OpenWrt-Devel] How to initialize multiple phy radios
Date: Sun, 24 Apr 2016 12:48:39 +0200	[thread overview]
Message-ID: <2596438.Cv6xmiar05@debian64> (raw)
In-Reply-To: <CA+i30h-Y_rB0kZfgWifk14Zw1CCkGZH5x5zf8+OH-GTwswXh3w@mail.gmail.com>

On Sunday, April 24, 2016 01:16:11 AM David Hutchison wrote:
> I spoke too soon:
> https://pci-ids.ucw.cz/read/PC/168c/0050
> 
> It is the QCA9887, so it's definitely on the PCIe bus and is being seen.
Does ath10k support the QCA9887? I see no entry for this pci-id (168c:0050)
in ath10k's pci table [0] and there's no definition of it in the hardware
header either [1]. The chip-id is also not present. I CC'ed ath10k, since
this seems to be a new chip that might be easy to add.
 
> On Sun, Apr 24, 2016 at 1:13 AM, David Hutchison
> <dhutchison@bluemesh.net> wrote:
> > Here is the PCI noise is in the kernel log from ath79_register_pci():
> >
> > [    0.510000] PCI host bridge to bus 0000:00
> > [    0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
> > [    0.520000] pci_bus 0000:00: root bus resource [io  0x0000]
> > [    0.520000] pci_bus 0000:00: No busn resource found for root bus,
> > will use [bus 00-ff]
> > [    0.530000] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000
> > [    0.530000] pci 0000:00:00.0: reg 10: [mem 0x10000000-0x101fffff 64bit]
> > [    0.530000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
> > [    0.530000] pci 0000:00:00.0: supports D1
> > [    0.530000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
> > [    0.530000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
> > [    0.530000] pci 0000:00:00.0: BAR 0: assigned [mem
> > 0x10000000-0x101fffff 64bit]
> > [    0.530000] pci 0000:00:00.0: BAR 6: assigned [mem
> > 0x10200000-0x1020ffff pref]
> > [    0.540000] pci 0000:00:00.0: using irq 40 for pin 1
> >
> > I compiled lspci in and it reports:
> > 00:00.0 Class 0280: 168c:0050
> >
> > As far as I know that's just a vendor/product ID, I tried looking it
> > up to verify that it was indeed the atheros qca988x but couldn't find
> > anything for certain.
> >
> > I verified ath10k is loaded:
> > ath10k_pci             27629  0
> > ath10k_core           247226  1 ath10k_pci
> > ath                    18726  4 ath10k_core,ath9k,ath9k_common,ath9k_hw
> > mac80211              389729  2 ath10k_core,ath9k
> > cfg80211              217396  5 ath10k_core,ath9k,ath9k_common,ath,mac80211
> > compat                 19304  7
> > ath10k_pci,ath10k_core,ath9k,ath9k_common,ath9k_hw,mac80211,cfg80211
> >

Regards,
Christian

[0] <https://git.kernel.org/cgit/linux/kernel/git/wireless/wireless-testing.git/tree/drivers/net/wireless/ath/ath10k/pci.c#n60>

[1] <https://git.kernel.org/cgit/linux/kernel/git/wireless/wireless-testing.git/tree/drivers/net/wireless/ath/ath10k/hw.h#n25>


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

       reply	other threads:[~2016-04-24 10:49 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <CA+i30h-5GCJ0h9REAJE8TCdxNQDe8Sa=Fs=gbxpHEW3fOY-hMw@mail.gmail.com>
     [not found] ` <CA+i30h--nmpjeNK4S02a9o9qrQ-b3QR77WcRorxC5-Dame5hBw@mail.gmail.com>
     [not found]   ` <CA+i30h-Y_rB0kZfgWifk14Zw1CCkGZH5x5zf8+OH-GTwswXh3w@mail.gmail.com>
2016-04-24 10:48     ` Christian Lamparter [this message]
2016-04-25 15:21       ` [OpenWrt-Devel] How to initialize multiple phy radios Valo, Kalle
2016-04-25 16:53         ` David Hutchison
2016-04-25 19:01           ` Christian Lamparter
2016-04-25 22:14             ` David Hutchison
2016-04-26  7:20             ` Valo, Kalle
2016-04-26 12:21               ` Christian Lamparter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=2596438.Cv6xmiar05@debian64 \
    --to=chunkeey@googlemail.com \
    --cc=ath10k@lists.infradead.org \
    --cc=dhutchison@bluemesh.net \
    --cc=openwrt-devel@lists.openwrt.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox