ATH10K Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Ben Greear <greearb@candelatech.com>
To: Sebastian Gottschall <s.gottschall@dd-wrt.com>,
	ath10k@lists.infradead.org
Subject: Re: possible memory leak or memory waste
Date: Mon, 25 May 2015 16:42:15 -0700	[thread overview]
Message-ID: <5563B357.9060309@candelatech.com> (raw)
In-Reply-To: <5563A990.5000606@dd-wrt.com>

Can you test with ath9k to make sure it is actually ath10k related?

And/or try traffic in RX direction only to see if that still uses
lots of memory?

Does memory come back after you just stop traffic (w/out stopping
hostapd)?

Thanks,
Ben


On 05/25/2015 04:00 PM, Sebastian Gottschall wrote:
> Am 26.05.2015 um 00:39 schrieb Ben Greear:
>> Default firmware has a hard-coded minimum number of tx buffers (somewhere
>> more than 1k buffers I think).  Maybe driver is allocating all this
>> memory somehow?
>>
>> If you do one-way traffic tests (udp), I wonder if you can tell if it is tx
>> or rx that consumes the memory?
> its tx. i have a ethernet over ip tunnel running on that link and i broadcast iptv in that way. (its my way to convert multicast to unicast)
> the  tunnel itself is rfc ethernet over ip, which is somewhat like udp. so connectionless protocol
>
> Sebastian
>>
>> CT firmware can be configured to use any multiple-of-8 amount of tx
>> buffers, though I have not tested below around 600.
>>
>> Thanks,
>> Ben
>>
>> On 05/25/2015 02:26 PM, Sebastian Gottschall wrote:
>>> today using the latest testing driver, i found out the memory consumption is unbelievable high.
>>> my router here has 64 mb ram. this ram is fully taken after some minutes by ath10k. but only if data flow present.
>>>
>>> here the results of "free" after some minutes
>>> root@DD-WRT:~# free
>>> total         used         free       shared      buffers
>>> Mem:         61636        58752         2884            0 2600
>>> -/+ buffers:              56152         5484
>>> Swap:            0            0            0
>>>
>>>
>>> now i terminate hostapd which controls the ath10k chipset
>>>
>>>
>>> root@DD-WRT:~# kill 902
>>> root@DD-WRT:~# free
>>> total         used         free       shared      buffers
>>> Mem:         61636        23212        38424            0 2416
>>> -/+ buffers:              20796        40840
>>> Swap:            0            0            0
>>>
>>>
>>> you see the difference?
>>>
>>>
>>> regards,
>>> Sebastian Gottschall
>>>
>>> _______________________________________________
>>> ath10k mailing list
>>> ath10k@lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>
>

-- 
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

  reply	other threads:[~2015-05-25 23:42 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-05-12 12:45 [PATCH] amth10k: fix promisc handling Michal Kazior
2015-05-21  5:40 ` Michal Kazior
2015-05-21  7:40   ` Kalle Valo
2015-05-25 12:25     ` Kalle Valo
2015-05-25 17:10       ` request: ACK timing setting required Sebastian Gottschall
2015-05-25 17:13         ` Ben Greear
2015-05-25 17:48           ` Sebastian Gottschall
2015-05-25 17:53             ` Ben Greear
2015-05-25 19:21               ` Sebastian Gottschall
2015-05-25 19:32                 ` Ben Greear
2015-05-25 20:31                   ` Sebastian Gottschall
2015-05-25 21:26                   ` possible memory leak or memory waste Sebastian Gottschall
2015-05-25 22:39                     ` Ben Greear
2015-05-25 23:00                       ` Sebastian Gottschall
2015-05-25 23:42                         ` Ben Greear [this message]
2015-05-26  0:07                           ` Sebastian Gottschall
2015-05-26  5:42                             ` Michal Kazior
2015-05-26  6:20                               ` Rajkumar Manoharan
2015-05-26  7:26                                 ` Sebastian Gottschall
2015-05-26  7:23                               ` Sebastian Gottschall
2015-05-26  8:26                                 ` Michal Kazior
2015-05-26  8:37                                   ` Sebastian Gottschall
2015-05-26  9:21                                     ` Michal Kazior
2015-05-26 11:19                                       ` Sebastian Gottschall
2015-05-27 10:25       ` [PATCH] amth10k: fix promisc handling Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=5563B357.9060309@candelatech.com \
    --to=greearb@candelatech.com \
    --cc=ath10k@lists.infradead.org \
    --cc=s.gottschall@dd-wrt.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox