Re: Question on bssid mask with ath10k

["\"Jose Núñez-Martínez (CTTC)\"" <jose.nunez@cttc.cat>]

Hi,
the reason for starting a virtual device in monitor mode is to infuence 
Rx filters in firmware as pointed out in [1]. The goal is to configure 
the wireless device in adhoc mode so that it can receive and send 
packets containing any mac destination address.

[1] http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html


Thx,
Jose

On 07/06/2015 04:33 PM, Ben Greear wrote:
> On 07/06/2015 06:54 AM, "Jose Núñez-Martínez (CTTC)" wrote:
>> Thanks for your answer. My goal was to create a monitor interface 
>> (mon2) and another (wlan2) in ibss mode associated to the same 
>> physical device. This is the
>> command I tried to create a virtual interface associated to phy0 in 
>> monitor mode:
>>
>> iw phy phy0 interface add moni2 type monitor
>
> That looks right...that command works for me.  Maybe you already had
> moni2 created incorrectly?  Try starting from fresh reboot or driver
> reload?
>
> Also, you should not actually need a monitor dev to have CT firmware work
> properly...but of course if you want to sniff frames, it can be useful.
>
> Thanks,
> Ben
>
>>
>> As you mentioned it is somehow configured as "managed" and not as 
>> monitor. Any ideas?
>>
>> Jose
>>
>> On 07/06/2015 03:39 PM, Ben Greear wrote:
>>> On 07/06/2015 06:23 AM, "Jose Núñez-Martínez (CTTC)" wrote:
>>>> Hi,
>>>> I upgraded to CT kernel and firmware. Now I have: Kernel is 4.0.4 
>>>> from CT and Firmware is 10.1.467-ct-com-full-014-96d543
>>>> However I cannot bring up two virtal interfaces associated to one 
>>>> physical device.
>>>>
>>>> The output of "iw dev" command:
>>>>
>>>> phy#1
>>>>      Interface moni2
>>>>          ifindex 9
>>>>          wdev 0x100000002
>>>>          addr 04:f0:21:18:26:a5
>>>>          type managed
>>>
>>> It is type managed...you created this wrong somehow.
>>>
>>> If you want to bring up more than one managed interface, you have to
>>> change the MAC address first so that they are unique.
>>>
>>> Thanks,
>>> Ben
>>>
>>>
>>>>      Interface wlan2
>>>>          ifindex 7
>>>>          wdev 0x100000001
>>>>          addr 04:f0:21:18:26:a5
>>>>          type IBSS
>>>>
>>>> This is the error shown when I try to bring up moni2 interface 
>>>> (ifconfig moni2 up): "SIOCSIFFLAGS: Name not unique on network"
>>>>
>>>>
>>>> Jose
>>>>
>>>> On 07/03/2015 12:45 PM, Michal Kazior wrote:
>>>>> On 3 July 2015 at 12:17, "Jose Núñez-Martínez (CTTC)"
>>>>> <jose.nunez@cttc.cat> wrote:
>>>>>> I'm trying to set BSSID mask in ath10k so that data packets with 
>>>>>> spoofed mac
>>>>>> destination address can be received (and not dropped) by the card.
>>>>>>
>>>>>> Apparently the way bssid mask is managed has changed from ath5k 
>>>>>> and ath9k
>>>>>> since there are not  "ath5k_hw_set_bssid_mask" or
>>>>>> "ath9k_htc_set_mac_bssid_mask"  kind of functions.
>>>>>>
>>>>>> Anyone tried this?
>>>>> There's no explicit control over Rx filters in ath10k that I know of.
>>>>> This is abstracted away by other firmware higher-level commands. One
>>>>> way to influence Rx filter (and BSSID mask) is to start a monitor 
>>>>> vdev
>>>>> in firmware. This apparently works[1] but 636 will crash on you again
>>>>> if you do that. You'll need Ben's CT firmware.
>>>>>
>>>>> [1]: 
>>>>> http://lists.infradead.org/pipermail/ath10k/2015-April/005095.html
>>>>>
>>>>>
>>>>> Michał
>>>>>
>>>>> _______________________________________________
>>>>> ath10k mailing list
>>>>> ath10k@lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>
>>>
>>>
>>
>
>


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k