From: Jorge Baranda <jbaranda@cttc.es>
To: ath10k@lists.infradead.org
Subject: Re: Setting up a VHT ad-hoc connection with ath10k
Date: Mon, 07 Sep 2015 12:36:41 +0200 [thread overview]
Message-ID: <55ED68B9.2060509@cttc.es> (raw)
In-Reply-To: <CALhHN=puF0RX=iSoxSH-GaEAhzb9eJbR38p7jOaXE7e3-dGDdw@mail.gmail.com>
Dear Janusz,
By firmware 636, do you mean the one named 999.999.0.636 in the url:
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware?
And then, if I use wpa_supplicant could it be possible to setup an ADHOC
connection.
I thought wpa_supplicant is used to setup STAs in combination with
hostapd (to setup APs).
Thank you very much for your time and attention,
Kind regards,
Jorge
El 07/09/15 12:22, Janusz Dziedzic escribió:
> On 7 September 2015 at 11:48, Jorge Baranda <jbaranda@cttc.es> wrote:
>> Dear all,
>>
>> Recently, I bought some WLE900VX cards and equipped several computers with
>> such cards.
>> I want to check the capabilties of these cards, so I have thought of
>> establishing an AD-HOC 802.11ac link in order to do so.
>> I have been able to establish and AD-HOC connection between two of these
>> cards, but I am sure I am not establishing an 802.11ac connection because
>> the iwlist tool only reports bit rates up to 54Mb/s for the established
>> connection.
>> I would be very grateful if someone could provide me some hints on
>> configuring these cards to work using the 802.11ac and to check that the
>> connection using such protocol has been established.
>>
> You should use 636 firmware and lastes wpa_supplicant. Wpa_supplicant
> will setup AC correctly (iw don't support this yet). After connected,
> check if you have correct BW (80MHz) using:
> iw wlan0 info
>
> Next you can run some traffic eg. using iperf and check RX rate using:
> iw wlan0 station dump.
>
> BR
> Janusz
>
>> Thank you very much in advance for your time and attention,
>>
>> With kind regards,
>>
>> --
>> Jorge Baranda
>> Research Engineer, MSc
>> jorge.baranda@cttc.es
>>
>> Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
>> Av. Carl Friedrich Gauss, 7
>> 08860 Castelldefels, Barcelona (Spain)
>> Tel: +34 93 645 29 00 Ext: 2171
>> Fax. +34 93 645 29 01
>> www.cttc.es
>>
>>
>> _______________________________________________
>> ath10k mailing list
>> ath10k@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/ath10k
> _______________________________________________
> ath10k mailing list
> ath10k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k
--
Jorge Baranda
Research Engineer, MSc
jorge.baranda@cttc.es
Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
Av. Carl Friedrich Gauss, 7
08860 Castelldefels, Barcelona (Spain)
Tel: +34 93 645 29 00 Ext: 2171
Fax. +34 93 645 29 01
www.cttc.es
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next prev parent reply other threads:[~2015-09-07 10:37 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-05 15:08 IBSS-RSN support on ath10k only links Alessandro Bolletta
2015-09-05 20:00 ` Janusz Dziedzic
2015-09-07 7:48 ` R: " Alessandro Bolletta
2015-09-07 8:02 ` Janusz Dziedzic
2015-09-07 8:03 ` R: " Alessandro Bolletta
2015-09-07 8:22 ` Janusz Dziedzic
2015-09-07 9:48 ` Setting up a VHT ad-hoc connection with ath10k Jorge Baranda
2015-09-07 10:22 ` Janusz Dziedzic
2015-09-07 10:36 ` Jorge Baranda [this message]
2015-09-07 15:36 ` IBSS-RSN support on ath10k only links Ben Greear
2015-09-07 15:40 ` R: " Alessandro Bolletta
2015-09-07 15:44 ` Ben Greear
2015-09-07 16:04 ` R: " Alessandro Bolletta
2015-09-07 16:59 ` Ben Greear
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55ED68B9.2060509@cttc.es \
--to=jbaranda@cttc.es \
--cc=ath10k@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox