ATH11K Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Rob Herring <robh@kernel.org>
To: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Cc: ath11k@lists.infradead.org, linux-wireless@vger.kernel.org,
	devicetree@vger.kernel.org
Subject: Re: [PATCH 19/19] dt: bindings: net: add bindings of WCN6750 for ath11k
Date: Tue, 23 Nov 2021 19:59:21 -0700	[thread overview]
Message-ID: <1637722761.019285.888171.nullmailer@robh.at.kernel.org> (raw)
In-Reply-To: <1637693434-15462-20-git-send-email-quic_mpubbise@quicinc.com>

On Wed, 24 Nov 2021 00:20:34 +0530, Manikanta Pubbisetty wrote:
> Add WCN6750 wireless driver support, its based on ath11k driver.
> 
> Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
> ---
>  .../bindings/net/wireless/qcom,ath11k.yaml         | 333 ++++++++++++++-------
>  1 file changed, 225 insertions(+), 108 deletions(-)
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:
./Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml:57:9: [warning] wrong indentation: expected 6 but found 8 (indentation)

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/net/wireless/qcom,ath11k.example.dt.yaml:0:0: /example-1/remoteproc@8a00000: failed to match any schema with compatible: ['qcom,sc7280-wpss-pil']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1558747

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

  reply	other threads:[~2021-11-24  2:59 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-11-23 18:50 [PATCH 00/19] add support for WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 01/19] ath11k: PCI changes to support WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 02/19] ath11k: Refactor PCI code to support hybrid bus devices Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 03/19] ath11k: Choose MSI config based on HW revision Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 04/19] ath11k: Refactor MSI logic Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 05/19] ath11k: Remove core PCI references from PCI common code Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 06/19] ath11k: Add HW params for WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 07/19] ath11k: Add bus " Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 08/19] ath11k: Add register access logic " Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 09/19] ath11k: Fetch device information via QMI " Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 10/19] ath11k: Add QMI changes " Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 11/19] ath11k: HAL changes to support WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 12/19] ath11k: Datapath " Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 13/19] ath11k: Fix RX de-fragmentation issue on WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 14/19] ath11k: Do not put HW in DBS mode for WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 15/19] ath11k: WMI changes to support WCN6750 Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 16/19] ath11k: Update WBM idle ring HP after FW mode on Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 17/19] ath11k: Add support for WCN6750 device Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 18/19] ath11k: Add support for targets without trustzone Manikanta Pubbisetty
2021-11-23 18:50 ` [PATCH 19/19] dt: bindings: net: add bindings of WCN6750 for ath11k Manikanta Pubbisetty
2021-11-24  2:59   ` Rob Herring [this message]
2021-11-28 16:20   ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1637722761.019285.888171.nullmailer@robh.at.kernel.org \
    --to=robh@kernel.org \
    --cc=ath11k@lists.infradead.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=quic_mpubbise@quicinc.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox