From: Baochen Qiang <quic_bqiang@quicinc.com>
To: david Atkins <david@3adesign.co.uk>,
"ath12k@lists.infradead.org" <ath12k@lists.infradead.org>
Subject: Re: wcn7850 issues
Date: Mon, 19 Aug 2024 10:33:35 +0800 [thread overview]
Message-ID: <cfe8e314-a28b-4ea3-85b2-9f5b4ac2db09@quicinc.com> (raw)
In-Reply-To: <LO0P123MB40573F46A6D63145363C6B13D6812@LO0P123MB4057.GBRP123.PROD.OUTLOOK.COM>
On 8/16/2024 8:23 PM, david Atkins wrote:
>> On 8/15/2024 4:38 AM, david Atkins wrote:
>>>>
>>>> On 8/6/2024 4:06 PM, david Atkins wrote:
>>>>> No support for EHT and therefore no MSC 12 or 13 which fits with the
>>>>> dmesg warning about it not being supported,
>>>> did not noted this ... So if AP does not support EHT, above warnings
>>>> makes sense, like you said.
>>>>
>>>
>>> Anseres inline, AP supports EHT
>>>
>>>> is this a card firmware
>>>>> issue rather than the driver?
>>>> did not follow you here, why is it an issue?
>>>>
>>>
>>> Is the firmware that’s uploaded to the card not supporting EHT?
>>>
>> FW does support EHT.
>>
>> You are checking scan results, so it is AP not advertising EHT support (actually
>> AP supports EHT, it is missing in scan results because IW does not print it. I
>> don't know your IW, but at least upstream IW does not print it currently), not
>> WCN7850.
>
>
> I have captured beacon packets from the AP, they show the presence of EHT, this is a snip from the packet decoded, is there something here that would prevent the Hamilton card seeing eht?
>
> Ext Tag: EHT Capabilities (802.11be D3.0)
> Ext Tag length: 14 (Tag len: 15)
> Ext Tag Number: EHT Capabilities (802.11be D3.0) (108)
> EHT MAC Capabilities Information: 0x0017, EPCS Priority Access Support, EHT OM Control Support, Triggered TXOP Sharing Mode 1 Support, Restricted TWT Support, Maximum MPDU Length: 3 895, EHT Link Adaptation Support: No feedback
> .... .... .... ...1 = EPCS Priority Access Support: Supported
> .... .... .... ..1. = EHT OM Control Support: Supported
> .... .... .... .1.. = Triggered TXOP Sharing Mode 1 Support: Supported
> .... .... .... 0... = Triggered TXOP Sharing Mode 2 Support: Not supported
> .... .... ...1 .... = Restricted TWT Support: Supported
> .... .... ..0. .... = SCS Traffic Description Support: Not supported
> .... .... 00.. .... = Maximum MPDU Length: 3 895 (0x0)
> .... ...0 .... .... = Maximum A-MPDU Length Exponent Extension: 0
> .... ..0. .... .... = EHT TRS Support: Not supported
> .... .0.. .... .... = TXOP Return Support In TXOP Sharing Mode 2: Not supported
> .... 0... .... .... = Two BQRs Support: Not supported
> ..00 .... .... .... = EHT Link Adaptation Support: No feedback (0)
> 00.. .... .... .... = Reserved: 0x0
> EHT PHY Capabilities Information
> EHT PHY Bits 0-15: 0xffe0
> .... .... .... ...0 = Reserved: 0x0
> .... .... .... ..0. = Support For 320 MHz in 6 GHz: Not supported
> .... .... .... .0.. = Support for 242-tone RU in BW Wider than 20 MHz: Not supported
> .... .... .... 0... = NDP With 4x EHT-LTF And 3.2 us GI: Not supported
> .... .... ...0 .... = Partial Bandwidth UL MU-MIMO: Not supported
> .... .... ..1. .... = SU Beamformer: Supported
> .... .... .1.. .... = SU Beamformee: Supported
> .... ..11 1... .... = Beamformee SS (<= 80 MHz): 0x7
> ...1 11.. .... .... = Beamformee SS (= 160 MHz): 0x7
> 111. .... .... .... = Beamformee SS (= 320 MHz): 0x7
> EHT PHY Bits 16-31: 0x00db
> .... .... .... .011 = Number Of Sounding Dimensions (<= 80 MHz): 0x3
> .... .... ..01 1... = Number Of Sounding Dimensions (= 160 MHz): 0x3
> .... ...0 11.. .... = Number Of Sounding Dimensions (= 320 MHz): 0x3
> .... ..0. .... .... = Ng = 16 SU Feedback: Not supported
> .... .0.. .... .... = Ng = 16 MU Feedback: Not supported
> .... 0... .... .... = Codebook Size = (4,2) SU Feedback: Not supported
> ...0 .... .... .... = Codebook Size = (7,5) MU Feedback: Not supported
> ..0. .... .... .... = Triggered SU Beamforming Feedback: Not supported
> .0.. .... .... .... = Triggered MU Beamforming Partial BW Feedback: Not supported
> 0... .... .... .... = Triggered CQI Feedback: Not supported
> EHT PHY Bits 32-39: 0x18
> .... ...0 = Partial Bandwidth DL MU-MIMO: Not supported
> .... ..0. = EHT PSR-Based SR support: Not supported
> .... .0.. = Power Boost Factor Support: Not supported
> .... 1... = EHT MU PPDU With 4x EHT-LTF and 0.8 us GI: Supported
> 0001 .... = Max Nc: 1
> EHT PHY Bits 40-63: 0x3ed876
> .... .... .... .... .... ...0 = Non-Triggered CQI Feedback: Not supported
> .... .... .... .... .... ..1. = Tx 1024-QAM & 4096-QAM < 242-tone RU Support: Supported
> .... .... .... .... .... .1.. = Rx 1024-QAM & 4096-QAM < 242-tone-RU Support: Supported
> .... .... .... .... .... 0... = PPE Thresholds Present: Not Present
> .... .... .... .... ..11 .... = Common Nominal Packet Padding: 3
> .... .... .... .000 01.. .... = Maximum Number Of Supported EHT-LTFs: 1
> .... .... .101 1... .... .... = Support Of MCS 15: 11
> .... .... 1... .... .... .... = Support Of EHT DUP (MCS 14) in 6 GHz: Supported
> .... ...0 .... .... .... .... = Support For 20 MHz Operating STA Receiving NDP With Wider BW: Not supported
> .... ..1. .... .... .... .... = Non-OFDMA UL MU-MIMO (BW <= 80 MHz): Supported
> .... .1.. .... .... .... .... = Non-OFDMA UL MU-MIMO (BW = 160 MHz): Supported
> .... 1... .... .... .... .... = Non-OFDMA UL MU-MIMO (BW = 320 MHz): Supported
> ...1 .... .... .... .... .... = MU Beamformer (BW <= 80 MHz): Supported
> ..1. .... .... .... .... .... = MU Beamformer (BW = 160 MHz): Supported
> .0.. .... .... .... .... .... = MU Beamformer (BW = 320 MHz): Not supported
> 0... .... .... .... .... .... = TB Sounding Feedback Rate Limit: Not supported
> EHT PHY Bits 64-71: 0x444400
> .... ...0 = Rx 1024-QAM In Wider Bandwidth DL OFDMA Support: Not supported
> .... ..0. = Rx 4096-QAM In Wider Bandwidth DL OFDMA SUpport: Not supported
> 0000 00.. = Reserved: 0x00
> Supported EHT-MCS and NSS Set
> EHT-MCS Map (BW <= 80MHz): 0x444444
> .... .... .... .... .... 0100 = Rx Max Nss That Supports EHT-MCS 0-9: 4
> .... .... .... .... 0100 .... = Tx Max Nss That Supports EHT-MCS 0-9: 4
> .... .... .... 0100 .... .... = Rx Max Nss That Supports EHT-MCS 10-11: 4
> .... .... 0100 .... .... .... = Tx Max Nss That Supports EHT-MCS 10-11: 4
> .... 0100 .... .... .... .... = Rx Max Nss That Supports EHT-MCS 12-13: 4
> 0100 .... .... .... .... .... = Tx Max Nss That Supports EHT-MCS 12-13: 4
> Ext Tag: EHT Operation (802.11be D3.0)
> Ext Tag length: 8 (Tag len: 9)
> Ext Tag Number: EHT Operation (802.11be D3.0) (106)
> EHT Operation Parameters: 0x01, EHT Operation Information Present
> .... ...1 = EHT Operation Information Present: True
> .... ..0. = Disabled Subchannel Bitmap Present: False
> .... .0.. = EHT Default PE Duration: False
> .... 0... = Group Addressed BU Indication Limit: False
> ..00 .... = Group Addressed BU Indication Exponent: 0
> 00.. .... = Reserved: 0x0
> Basic EHT-MCS And Nss Set: 0x44444444
this means AP requires STA NSS to be equal or larger than 4, however WCN7850 only support 2, so connection in EHT is rejected.
> Control: 0x02, Channel Width: 80 MHz EHT BSS bandwidth
> .... .010 = Channel Width: 80 MHz EHT BSS bandwidth (2)
> 0000 0... = Reserved: 0x00
> CCFS0: 0x0000006a
> CCFS1: 0x00000000
>
>
next prev parent reply other threads:[~2024-08-19 2:33 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <LO0P123MB4057D6C2F6FEFF335B30EE7CD6BF2@LO0P123MB4057.GBRP123.PROD.OUTLOOK.COM>
2024-08-06 8:06 ` wcn7850 issues david Atkins
2024-08-13 13:20 ` david Atkins
2024-08-14 7:28 ` Kang Yang
2024-08-14 8:46 ` Lingbo Kong
2024-08-14 10:33 ` Baochen Qiang
2024-08-14 16:58 ` david Atkins
2024-08-14 10:42 ` Baochen Qiang
2024-08-14 17:00 ` david Atkins
2024-08-14 20:38 ` david Atkins
2024-08-15 2:15 ` Baochen Qiang
2024-08-16 12:23 ` david Atkins
2024-08-19 2:33 ` Baochen Qiang [this message]
2024-08-19 10:55 ` david Atkins
2024-08-30 5:55 ` david Atkins
2024-08-30 7:08 ` Baochen Qiang
2024-09-01 7:39 ` david Atkins
2024-09-02 1:56 ` Baochen Qiang
2024-09-02 6:03 ` david Atkins
2024-09-02 6:20 ` Baochen Qiang
2024-09-03 6:29 ` david Atkins
2024-09-03 7:47 ` Kalle Valo
2024-09-03 9:57 ` Janusz Dziedzic
2024-09-03 10:07 ` Johannes Berg
2024-09-03 10:09 ` Kalle Valo
2024-09-03 21:15 ` david Atkins
2024-09-04 5:08 ` Janusz Dziedzic
2024-09-04 6:04 ` david Atkins
2024-09-04 7:08 ` Janusz Dziedzic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cfe8e314-a28b-4ea3-85b2-9f5b4ac2db09@quicinc.com \
--to=quic_bqiang@quicinc.com \
--cc=ath12k@lists.infradead.org \
--cc=david@3adesign.co.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox