From: Paul Fertser <fercerpav@gmail.com>
To: b43-dev@lists.infradead.org
Subject: Issues with 14e4:4315 on "lenovo ideapad s9" - works only after wl
Date: Sat, 9 Oct 2010 22:36:37 +0400 [thread overview]
Message-ID: <20101009183637.GT1593@home.pavel.comp> (raw)
In-Reply-To: <20101009115320.GR1593@home.pavel.comp>
On Sat, Oct 09, 2010 at 03:53:20PM +0400, Paul Fertser wrote:
> The card works as expected with the sta driver, and b43 handles it nicely
> after unloading wl and loading b43
I'd expect lack of txpower adjustment for LP might very well be the cause for
this. The specs seem to be ready so probably implementing this part would not
be too hard.
In case it might be of interest, ssb sprom contents attached.
--
Be free, use free (http://www.gnu.org/philosophy/free-sw.html) software!
mailto:fercerpav at gmail.com
-------------- next part --------------
SPROM(0x082), brev, Board revision = 0x01
SPROM(0x09C), antbg0, Available antenna bitmask for 2 GHz = 0x03
SPROM(0x09C), anta0, Available antenna bitmask for 5 GHz = 0x00
SPROM(0x09E), antg0, Antenna 0 gain = 0x02
SPROM(0x09E), antg1, Antenna 1 gain = 0xFF
SPROM(0x0A0), antg2, Antenna 2 gain = 0xFF
SPROM(0x0A0), antg3, Antenna 3 gain = 0xFF
SPROM(0x062), tpi2g0, TX Power Index 2GHz = 0x8000
SPROM(0x064), tpi2g1, TX Power Index 2GHz = 0x0002
SPROM(0x066), tpi5gm0, TX Power Index 5GHz middle subband = 0x0000
SPROM(0x068), tpi5gm1, TX Power Index 5GHz middle subband = 0x1F30
SPROM(0x06A), tpi5gl0, TX Power Index 5GHz low subband = 0x1800
SPROM(0x06C), tpi5gl1, TX Power Index 5GHz low subband = 0x0000
SPROM(0x06E), tpi5gh0, TX Power Index 5GHz high subband = 0x0000
SPROM(0x070), tpi5gh1, TX Power Index 5GHz high subband = 0xFFFF
SPROM(0x140), cckpo2g, 2 GHz CCK power offset = 0xFFFF
SPROM(0x142), ofdm2g, 2 GHz OFDM power offset = 0xFFFF0008
SPROM(0x146), ofdm5gm, 5 GHz OFDM middle subband power offset = 0xFFFFFFFF
SPROM(0x14A), ofdm5gl, 5 GHz OFDM low subband power offset = 0xFFFFFFFF
SPROM(0x14E), ofdm5gh, 5 GHz OFDM high subband power offset = 0xFFFFFFFF
SPROM(0x152), mcspo2, 2 GHz MCS power offset = 0xFFFF
SPROM(0x162), mcspo5m, 5 GHz middle subband MCS power offset = 0xFFFF
SPROM(0x172), mcspo5l, 5 GHz low subband MCS power offset = 0xFFFF
SPROM(0x182), mcspo5h, 5 GHz high subband MCS power offset = 0xFFFF
SPROM(0x192), ccdpo, CCD power offset = 0xFFFF
SPROM(0x194), stbcpo, STBC power offset = 0xFFFF
SPROM(0x196), bw40po, BW40 power offset = 0xFFFF
SPROM(0x198), bwduppo, BWDUP power offset = 0xFFFF
SPROM(0x0C2), pa0b0, SISO (Path 1) Power Amplifier W0 PAB0 = 0x1797
SPROM(0x0C4), pa0b1, SISO (Path 1) Power Amplifier W0 PAB1 = 0xFA35
SPROM(0x0C6), pa0b2, SISO (Path 1) Power Amplifier W0 PAB2 = 0xFE7B
SPROM(0x0CC), pa5m0, SISO (Path 1) 5 GHz Power Amplifier middle 0 = 0xFFFF
SPROM(0x0CE), pa5m1, SISO (Path 1) 5 GHz Power Amplifier middle 1 = 0xFFFF
SPROM(0x0D0), pa5m2, SISO (Path 1) 5 GHz Power Amplifier middle 2 = 0xFFFF
SPROM(0x0D2), pa5l0, SISO (Path 1) 5 GHz Power Amplifier low 0 = 0xFFFF
SPROM(0x0D4), pa5l1, SISO (Path 1) 5 GHz Power Amplifier low 1 = 0xFFFF
SPROM(0x0D6), pa5l2, SISO (Path 1) 5 GHz Power Amplifier low 2 = 0xFFFF
SPROM(0x0D8), pa5h0, SISO (Path 1) 5 GHz Power Amplifier high 0 = 0xFFFF
SPROM(0x0DA), pa5h1, SISO (Path 1) 5 GHz Power Amplifier high 1 = 0xFFFF
SPROM(0x0DC), pa5h2, SISO (Path 1) 5 GHz Power Amplifier high 2 = 0xFFFF
SPROM(0x0C0), maxpbg, Max power 2GHz - Path 1 = 0x4A
SPROM(0x0CA), maxpa, Max power 5GHz - Path 1 = 0xFF
SPROM(0x0C0), itssibg, Idle TSSI target 2 GHz - Path 1 = 0x3E
SPROM(0x0CA), itssia, Idle TSSI target 5 GHz - Path 1 = 0xFF
SPROM(0x08C), macadr, MAC Address = 0c:60:76:9a:49:36
SPROM(0x004), subp, Subsystem Product ID = 0x04B5
SPROM(0x006), subv, Subsystem Vendor ID = 0x14E4
SPROM(0x008), ppid, PCI Product ID = 0x0078
SPROM(0x086), bflhi, High 16 bits of boardflags = 0x0002
SPROM(0x084), bfl, Low 16 bits of boardflags = 0x0201
SPROM(0x094), regrev, Regulatory revision = 0x000C
SPROM(0x092), ccode, Country Code = "US"
The input file is data from a revision 8 SPROM.
-------------- next part --------------
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
\0
next prev parent reply other threads:[~2010-10-09 18:36 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-09 11:53 Issues with 14e4:4315 on "lenovo ideapad s9" - works only after wl Paul Fertser
2010-10-09 18:36 ` Paul Fertser [this message]
2010-10-09 20:37 ` Gábor Stefanik
2010-10-09 21:32 ` Paul Fertser
2010-10-09 21:37 ` Gábor Stefanik
2010-10-10 7:21 ` Paul Fertser
2010-10-10 15:39 ` Larry Finger
2010-10-10 17:03 ` Paul Fertser
2010-10-11 1:50 ` Larry Finger
2010-10-11 7:37 ` Rafał Miłecki
2010-10-13 6:58 ` PIO mode (was: Re: Issues with 14e4:4315 on "lenovo ideapad s9" - works only after wl) Paul Fertser
2010-10-17 22:35 ` PIO mode Larry Finger
2010-10-18 4:11 ` Paul Fertser
2010-10-18 19:57 ` Larry Finger
2010-10-19 0:43 ` Paul Fertser
2010-10-19 16:04 ` Larry Finger
2010-10-19 16:22 ` Paul Fertser
2010-10-19 17:02 ` Larry Finger
2010-10-20 17:37 ` Larry Finger
2010-10-20 17:54 ` Paul Fertser
2010-10-20 18:31 ` Larry Finger
2010-10-20 19:37 ` MMIO trace for "warm" boot of b43 on IdeaPad S9 (was: Re: PIO mode) Paul Fertser
2010-10-20 22:19 ` Larry Finger
2010-10-21 6:05 ` MMIO trace for "warm" boot of b43 on IdeaPad S9 Paul Fertser
2010-10-21 8:53 ` Transfer zeroes via ssh test (was: Re: PIO mode) Paul Fertser
2010-10-21 14:27 ` Larry Finger
2010-10-21 20:55 ` Michael Büsch
2010-10-10 16:50 ` Issues with 14e4:4315 on "lenovo ideapad s9" - works only after wl Gábor Stefanik
2010-10-12 22:12 ` Paul Fertser
2010-10-12 23:05 ` Paul Fertser
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20101009183637.GT1593@home.pavel.comp \
--to=fercerpav@gmail.com \
--cc=b43-dev@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).