installing b43 from wiki debian, but don't found wlan0 or eth2...

installing b43 from wiki debian, but don't found wlan0 or eth2...

[Paulo Riquelme]

hello list, i'm new in this list, and i don't speak english but i try
explain my problem:
- i install debian squeeze (i have kernel 2.6.32-5-amd64)
- i search and found
http://wiki.debian.org/bcm43xx#b43-b43legacy-squeezefor to install
drivers to my wifi (i have a compaq 515, from lspci -nn =>
06:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g
LP-PHY [14e4:4315] (rev 01))
- in the steps of the page i:
    - add repository contrib non-free
    - aptitude update
    - wireless-tools package is already installed (for default from the
installation)
    - aptitude install firmware-b43-lpphy-installer (my appropiate firmware)
    - after i  write in the shell modprobe b43
    - at time of verify my device has an available interface write iwconfig
and appear:
              lo   no wireless extension
              eth0     no wireless extension
              pan0    no wireless extension

     - i try writing dpkg-reconfigure firmware-b43-lpphy-installer

but nothing, part of a dmesg:
[    1.354473]  sda:sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda tray
[    1.358141] Uniform CD-ROM driver Revision: 3.20
[    1.358267] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.392172]  sda1 sda2 < sda5 sda6 >
[    1.417188] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.422905] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.422951] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.463694] usb 3-2: New USB device found, idVendor=04f2, idProduct=b159
[    1.463699] usb 3-2: New USB device strings: Mfr=2, Product=1,
SerialNumber=3
[    1.463702] usb 3-2: Product: CNF8243
[    1.463705] usb 3-2: Manufacturer: Chicony Electronics Co., Ltd.
[    1.463707] usb 3-2: SerialNumber: SN0001
[    1.463820] usb 3-2: configuration #1 chosen from 1 choice
[    1.832933] PM: Starting manual resume from disk
[    1.832939] PM: Resume from partition 8:5
[    1.832941] PM: Checking hibernation image.
[    1.833220] PM: Error -22 checking image file
[    1.833224] PM: Resume from disk failed.
[    1.891815] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    3.822260] udev: starting version 157
[    4.436623] ACPI: AC Adapter [AC] (on-line)
[    4.442091] processor LNXCPU:00: registered as cooling_device11
[    4.442235] processor LNXCPU:01: registered as cooling_device12
[    4.472115] ACPI: WMI: Mapper loaded
[    4.514934] input: Sleep Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    4.514945] ACPI: Sleep Button [SLPB]
[    4.515026] input: Lid Switch as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[    4.515210] ACPI: Lid Switch [LID]
[    4.515299] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[    4.515303] ACPI: Power Button [PWRF]
[    4.536679] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    4.582542] ACPI: Battery Slot [BAT0] (battery present)
[    4.752731] acpi device:01: registered as cooling_device13
[    4.753393] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:00/LNXVIDEO:00/input/input6
[    4.753463] ACPI: Video Device [IGFX] (multi-head: yes  rom: no  post:
no)
[    4.851455] EDAC MC: Ver: 2.1.0 Jun  1 2010
[    4.852786] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00,
revision 0
[    4.876833] EDAC amd64_edac:  Ver: 3.2.0 Jun  1 2010
[    4.876906] EDAC amd64: This node reports that Memory ECC is currently
disabled, set F3x44[22] (0000:00:18.3).
[    4.876930] EDAC amd64: ECC disabled in the BIOS or no ECC capability,
module will not load.
[    4.876931]  Either enable ECC checking or force module loading by
setting 'ecc_enable_override'.
[    4.876933]  (Note that use of the override may cause unknown side
effects.)
[    4.876942] amd64_edac: probe of 0000:00:18.2 failed with error -22
[    4.894064] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    4.896598] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 9602 ss_vid
0 ss_did 0
[    4.896603] shpchp 0000:00:01.0: Cannot reserve MMIO region
[    4.896718] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    5.000071] [drm] Initialized drm 1.1.0 20060810
[    5.007587] Linux video capture interface: v2.00
[    5.054532] uvcvideo: Found UVC 1.00 device CNF8243 (04f2:b159)
[    5.112309] input: CNF8243 as
/devices/pci0000:00/0000:00:13.2/usb3/3-2/3-2:1.0/input/input7
[    5.112406] usbcore: registered new interface driver uvcvideo
[    5.112649] USB Video Class driver (v0.1.0)
[    5.265438] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps:
0xd04731/0xa40000/0xa0000
[    5.306094] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio4/input/input8
[    5.504529] [drm] radeon kernel modesetting enabled.
[    5.504625] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ
18
[    5.504631] radeon 0000:01:05.0: setting latency timer to 64
[    5.509277] [drm] radeon: Initializing kernel modesetting.
[    5.509410] [drm] register mmio base: 0xD4300000
[    5.509413] [drm] register mmio size: 65536
[    5.509568] ATOM BIOS: HP_Volna
[    5.509595] [drm] Clocks initialized !
[    5.509817] [drm] Detected VRAM RAM=256M, BAR=256M
[    5.509822] [drm] RAM width 32bits DDR
[    5.509969] [TTM] Zone  kernel: Available graphics memory: 1416272 kiB.
[    5.509994] [drm] radeon: 256M of VRAM memory ready
[    5.509996] [drm] radeon: 512M of GTT memory ready.
[    5.510049] [drm] radeon: irq initialized.
[    5.510053] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    5.511350] [drm] Loading RS780 Microcode
[    5.511991] platform radeon_cp.0: firmware: requesting
radeon/RS780_pfp.bin
[    5.568606] r600_cp: Failed to load firmware "radeon/RS780_pfp.bin"
[    5.568689] [drm:r600_startup] *ERROR* Failed to load firmware!
[    5.568734] radeon 0000:01:05.0: disabling GPU acceleration
[    5.568807] radeon 0000:01:05.0: ffff8800ae20d200 unpin not necessary
[    5.568810] radeon 0000:01:05.0: ffff8800ae20d200 unpin not necessary
[    5.568836] [drm] Enabling audio support
[    5.569009] [drm] Radeon Display Connectors
[    5.569011] [drm] Connector 0:
[    5.569013] [drm]   VGA
[    5.569016] [drm]   DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c
0x7e4c
[    5.569018] [drm]   Encoders:
[    5.569020] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    5.569023] [drm] Connector 1:
[    5.569024] [drm]   LVDS
[    5.569027] [drm]   DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c
0x7e5c
[    5.569029] [drm]   Encoders:
[    5.569031] [drm]     LCD1: INTERNAL_KLDSCP_LVTMA
[    5.710716] [drm] fb mappable at 0xC0040000
[    5.710719] [drm] vram apper at 0xC0000000
[    5.710721] [drm] size 4325376
[    5.710723] [drm] fb depth is 24
[    5.710725] [drm]    pitch is 5632
[    5.860137] HDA Intel 0000:00:14.2: power state changed by ACPI to D0
[    5.860228] HDA Intel 0000:00:14.2: power state changed by ACPI to D0
[    5.860272] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[    6.115425] input: HDA Digital PCBeep as
/devices/pci0000:00/0000:00:14.2/input/input9
[    6.129107] input: HDA ATI SB Mic at Ext Front Jack as
/devices/pci0000:00/0000:00:14.2/sound/card0/input10
[    6.129226] input: HDA ATI SB HP Out at Ext Front Jack as
/devices/pci0000:00/0000:00:14.2/sound/card0/input11
[    6.666574] Console: switching to colour frame buffer device 170x48
[    6.685199] fb0: radeondrmfb frame buffer device
[    6.685201] registered panic notifier
[    6.685222] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:05.0 on
minor 0
[    7.113733] Adding 2928632k swap on /dev/sda5.  Priority:-1 extents:1
across:2928632k
[    7.472955] loop: module loaded
[    7.904456] EXT4-fs (sda6): mounted filesystem with ordered data mode
[    9.089262] sky2 eth0: enabling interface
[    9.090067] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    9.189062] fuse init (API version 7.13)
[   10.080554] input: ACPI Virtual Keyboard Device as
/devices/virtual/input/input12
[   10.593874] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control
both
[   10.594723] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.609917] powernow-k8: Found 1 AMD Athlon(tm)X2 DualCore QL-64
processors (2 cpu cores) (version 2.20.00)
[   11.609974] powernow-k8:    0 : pstate 0 (2100 MHz)
[   11.609976] powernow-k8:    1 : pstate 1 (1050 MHz)
[   13.888408] Bluetooth: Core ver 2.15
[   13.888944] NET: Registered protocol family 31
[   13.888948] Bluetooth: HCI device and connection manager initialized
[   13.888956] Bluetooth: HCI socket layer initialized
[   13.896134] Bluetooth: L2CAP ver 2.14
[   13.896137] Bluetooth: L2CAP socket layer initialized
[   13.926497] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   13.926503] Bluetooth: BNEP filters: protocol multicast
[   13.961350] Bridge firewalling registered
[   13.972668] Bluetooth: SCO (Voice Link) ver 0.6
[   13.972674] Bluetooth: SCO socket layer initialized
[   14.089834] lp: driver loaded but no devices found
[   14.104811] ppdev: user-space parallel port driver
[   21.504058] eth0: no IPv6 routers present
[   22.294929] CPU0 attaching NULL sched-domain.
[   22.294945] CPU1 attaching NULL sched-domain.
[   22.324223] CPU0 attaching sched-domain:
[   22.324233]  domain 0: span 0-1 level MC
[   22.324239]   groups: 0 1
[   22.324254] CPU1 attaching sched-domain:
[   22.324258]  domain 0: span 0-1 level MC
[   22.324263]   groups: 1 0
[ 2030.498525] cfg80211: Using static regulatory domain info
[ 2030.498532] cfg80211: Regulatory domain: US
[ 2030.498536]     (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 2030.498543]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700
mBm)
[ 2030.498549]     (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300
mBm)
[ 2030.498554]     (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300
mBm)
[ 2030.498560]     (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300
mBm)
[ 2030.498566]     (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300
mBm)
[ 2030.498572]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000
mBm)
[ 2030.499364] cfg80211: Calling CRDA for country: US
[ 2030.608612] Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID:
FW13 ]

a question: must remove the ssb module and put it in the blacklist???

i wait for your answer, thank you, sorry for my bad english jej,

Paulo.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/b43-dev/attachments/20100614/b20d94dd/attachment.html>

installing b43 from wiki debian, but don't found wlan0 or eth2...

[Larry Finger]

On 06/13/2010 11:51 PM, Paulo Riquelme wrote:
> hello list, i'm new in this list, and i don't speak english but i try
> explain my problem:
> - i install debian squeeze (i have kernel 2.6.32-5-amd64)
--snip--

> 3000 mBm)
> [ 2030.499364] cfg80211: Calling CRDA for country: US
> [ 2030.608612] Broadcom 43xx driver loaded [ Features: PMLS,
> Firmware-ID: FW13 ]
> 
> a question: must remove the ssb module and put it in the blacklist???
> 
> i wait for your answer, thank you, sorry for my bad english jej,

Your English is fine. I had no trouble understanding what you did.

I am not a Debian user and may have missed something, but your set of
commands look right.

You should not blacklist ssb. The b43 driver uses ssb for its low-level
operations, thus ssb is necessary. Tou should not have to modprobe b43
either. Does your blacklist contain either b43 or ssb? If so, remove the
entry.

Your dmesg output ends just where I would expect to see any error messages.

Please reboot and post the output of

lsmod | egrep "ssb|b43"
dmesg | egrep "ssb|b43"

Larry