From: Sven Eckelmann <sven@narfation.org>
To: b.a.t.m.a.n@lists.open-mesh.org
Cc: "Jiri Pirko" <jiri@mellanox.com>,
netdev@vger.kernel.org, "Sven Eckelmann" <sven@narfation.org>,
"Linus Lüssing" <linus.luessing@c0d3.blue>
Subject: [B.A.T.M.A.N.] [RFC v4 17/19] batman-adv: Add elp_interval hardif genl configuration
Date: Sat, 19 Jan 2019 16:56:24 +0100 [thread overview]
Message-ID: <20190119155626.6414-18-sven@narfation.org> (raw)
In-Reply-To: <20190119155626.6414-1-sven@narfation.org>
The ELP packets are transmitted every elp_interval milliseconds on an
slave/hard-interface. This value can be changed using the configuration
interface.
The BATADV_CMD_SET_HARDIF/BATADV_CMD_GET_HARDIF commands allow to set/get
the configuration of this feature using the u32 BATADV_ATTR_ELP_INTERVAL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
---
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
---
include/uapi/linux/batman_adv.h | 6 ++++++
net/batman-adv/netlink.c | 17 +++++++++++++++++
2 files changed, 23 insertions(+)
diff --git a/include/uapi/linux/batman_adv.h b/include/uapi/linux/batman_adv.h
index 5c18d454..a2abbf7d 100644
--- a/include/uapi/linux/batman_adv.h
+++ b/include/uapi/linux/batman_adv.h
@@ -476,6 +476,12 @@ enum batadv_nl_attrs {
*/
BATADV_ATTR_ORIG_INTERVAL,
+ /**
+ * @BATADV_ATTR_ELP_INTERVAL: defines the interval in milliseconds in
+ * which batman emits probing packets for neighbor sensing (ELP).
+ */
+ BATADV_ATTR_ELP_INTERVAL,
+
/* add attributes above here, update the policy in netlink.c */
/**
diff --git a/net/batman-adv/netlink.c b/net/batman-adv/netlink.c
index fbb75177..48d33ae4 100644
--- a/net/batman-adv/netlink.c
+++ b/net/batman-adv/netlink.c
@@ -159,6 +159,7 @@ static const struct nla_policy batadv_netlink_policy[NUM_BATADV_ATTR] = {
[BATADV_ATTR_MULTICAST_MODE_ENABLED] = { .type = NLA_U8 },
[BATADV_ATTR_NETWORK_CODING_ENABLED] = { .type = NLA_U8 },
[BATADV_ATTR_ORIG_INTERVAL] = { .type = NLA_U32 },
+ [BATADV_ATTR_ELP_INTERVAL] = { .type = NLA_U32 },
};
/**
@@ -825,6 +826,12 @@ static int batadv_netlink_hardif_put(struct sk_buff *msg,
goto nla_put_failure;
}
+#ifdef CONFIG_BATMAN_ADV_BATMAN_V
+ if (nla_put_u32(msg, BATADV_ATTR_ELP_INTERVAL,
+ atomic_read(&hard_iface->bat_v.elp_interval)))
+ goto nla_put_failure;
+#endif /* CONFIG_BATMAN_ADV_BATMAN_V */
+
genlmsg_end(msg, hdr);
return 0;
@@ -910,6 +917,16 @@ static int batadv_netlink_set_hardif(struct sk_buff *skb,
struct batadv_hard_iface *hard_iface = info->user_ptr[1];
struct batadv_priv *bat_priv = info->user_ptr[0];
+#ifdef CONFIG_BATMAN_ADV_BATMAN_V
+ struct nlattr *attr;
+
+ if (info->attrs[BATADV_ATTR_ELP_INTERVAL]) {
+ attr = info->attrs[BATADV_ATTR_ELP_INTERVAL];
+
+ atomic_set(&hard_iface->bat_v.elp_interval, nla_get_u32(attr));
+ }
+#endif /* CONFIG_BATMAN_ADV_BATMAN_V */
+
batadv_netlink_notify_hardif(bat_priv, hard_iface);
return 0;
--
2.20.1
next prev parent reply other threads:[~2019-01-19 15:56 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-19 15:56 [B.A.T.M.A.N.] [RFC v4 00/19] batman-adv: netlink restructuring, part 2 Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 01/19] batman-adv: Move common genl doit code pre/post hooks Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 02/19] batman-adv: Prepare framework for mesh genl config Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 03/19] batman-adv: Prepare framework for hardif " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 04/19] batman-adv: Prepare framework for vlan " Sven Eckelmann
2019-01-21 9:44 ` Jiri Pirko
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 05/19] batman-adv: Add aggregated_ogms mesh genl configuration Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 06/19] batman-adv: Add ap_isolation mesh/vlan " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 07/19] batman-adv: Add bonding mesh " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 08/19] batman-adv: Add bridge_loop_avoidance " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 09/19] batman-adv: Add distributed_arp_table " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 10/19] batman-adv: Add fragmentation " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 11/19] batman-adv: Add gateway " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 12/19] batman-adv: Add hop_penalty " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 13/19] batman-adv: Add log_level " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 14/19] batman-adv: Add multicast_mode " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 15/19] batman-adv: Add network_coding " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 16/19] batman-adv: Add orig_interval " Sven Eckelmann
2019-01-19 15:56 ` Sven Eckelmann [this message]
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 18/19] batman-adv: Add throughput_override hardif " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 19/19] batman-adv: Trigger genl notification on sysfs config change Sven Eckelmann
2019-01-21 9:47 ` [B.A.T.M.A.N.] [RFC v4 00/19] batman-adv: netlink restructuring, part 2 Jiri Pirko
2019-01-26 10:47 ` Sven Eckelmann
2019-01-27 8:45 ` Jiri Pirko
2019-02-05 17:04 ` Simon Wunderlich
2019-02-05 19:24 ` Linus Lüssing
2019-02-06 18:20 ` Sven Eckelmann
2019-02-06 19:08 ` Linus Lüssing
2019-02-07 10:02 ` Sven Eckelmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190119155626.6414-18-sven@narfation.org \
--to=sven@narfation.org \
--cc=b.a.t.m.a.n@lists.open-mesh.org \
--cc=jiri@mellanox.com \
--cc=linus.luessing@c0d3.blue \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox