Buildroot Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Martin Peevski <martin@ronetix.at>
To: buildroot@busybox.net
Subject: [Buildroot] Fwd: Re:  Basic questions about using BuildRoot
Date: Sat, 29 Sep 2012 17:09:44 +0300	[thread overview]
Message-ID: <50670128.7090203@ronetix.at> (raw)
In-Reply-To: <5066FE59.9060600@relinux.de>

On 29/09/12 16:57, Stephan Hoffmann wrote:
> Am 29.09.2012 15:17, schrieb Martin Peevski:
>> On 28/09/12 17:02, Martin Peevski wrote:
>>> Also want to ask because I was impossible to configure the Buildroot
>>> using Kernel sources from my computer. Is it possible and how? If
>>> it's impossible I can deliver the sources via internet but they are
>>> not in Git repository, is that problem?
> Hi Martin,
>
> you can use a local linux source tree with the source directory override
> mechanism described here: http://free-electrons.com/blog/buildroot-2011-11/
>>> Thanks in advance!
>>> Martin
>>> _______________________________________________
>>> buildroot mailing list
>>> buildroot at busybox.net
>>> http://lists.busybox.net/mailman/listinfo/buildroot
>>
>>
>> Hi again! Before response to my previous letter I want to tell you
>> that build together the kernel and the rootfs and my ethernet is still
>> not working. Can you help me resolve the problem, please? Is the
>> ethernet dependent on my Buildroot configuration or may be something
>> another?
> Do you have any further diagnostics like kernel messages or such? Do you
> have a working kernel for your board? If yes, did you double-check
> kernel configuration against the known good one? If no, are you sure
> your hardware is working correctly? Can you set an IP address without
> error messages?
>
> Regards
>
> Stephan
>> Thanks, Martin.
>> _______________________________________________
>> buildroot mailing list
>> buildroot at busybox.net
>> http://lists.busybox.net/mailman/listinfo/buildroot
>
I'm not build the Kernel with diagnostic information but I have working 
Kernel and may be rootfs because I have command prompt with buildroot. 
Can execute ifconfig command but the response don't show my IP, shows 
only this:
# ifconfig
lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

I think I'm sure that the Kernel is working because with another rootfs 
my Ethernet is working - can read the IP with ifconfig. But I must use 
the rootfs from Buildroot because the small size of it.

  reply	other threads:[~2012-09-29 14:09 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-09-15 17:29 [Buildroot] Basic questions about using BuildRoot Martin Peevski
2012-09-15 17:50 ` Thomas De Schampheleire
     [not found]   ` <5054C649.6000006@ronetix.at>
2012-09-15 18:26     ` Thomas De Schampheleire
     [not found]       ` <5055A940.7070802@ronetix.at>
2012-09-16 11:12         ` [Buildroot] Fwd: " Thomas De Schampheleire
     [not found]           ` <5055C935.3050108@ronetix.at>
2012-09-17 10:43             ` Thomas De Schampheleire
2012-09-18 22:06               ` Arnout Vandecappelle
2012-09-20  6:19                 ` Martin Peevski
2012-09-27  8:55                   ` Martin Peevski
2012-09-27  9:53                     ` Thomas Petazzoni
2012-09-27 10:42                       ` Arnout Vandecappelle
2012-09-27 11:57                       ` Martin Peevski
2012-09-27 12:21                         ` Thomas Petazzoni
2012-09-28 14:02                           ` Martin Peevski
2012-09-29 13:17                             ` Martin Peevski
2012-09-29 13:57                               ` Stephan Hoffmann
2012-09-29 14:09                                 ` Martin Peevski [this message]
2012-09-29 14:14                                   ` Stephan Hoffmann
2012-10-01  8:14                                     ` Martin Peevski
2012-10-01  8:29                                       ` Stephan Hoffmann
2012-10-01  8:40                                       ` Samuel Martin
2012-10-01  9:06                                         ` Martin Peevski
2012-10-01  9:11                                           ` Samuel Martin
2012-10-01  9:17                                             ` Martin Peevski
2012-10-01 12:51                                               ` Martin Peevski
2012-10-03 15:05                                               ` Martin Peevski

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=50670128.7090203@ronetix.at \
    --to=martin@ronetix.at \
    --cc=buildroot@busybox.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox