From mboxrd@z Thu Jan 1 00:00:00 1970 From: Arnout Vandecappelle Date: Mon, 17 Dec 2012 23:01:43 +0100 Subject: [Buildroot] [PATCH] imx-lib: new package In-Reply-To: <87mwxc76je.fsf@dell.be.48ers.dk> References: <1355752131-31966-1-git-send-email-arnout@mind.be> <50CF5987.90805@mind.be> <87mwxc76je.fsf@dell.be.48ers.dk> Message-ID: <50CF9647.3020506@mind.be> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: buildroot@busybox.net On 17/12/12 21:44, Peter Korsgaard wrote: >>>>>> "Arnout" == Arnout Vandecappelle writes: > > Arnout> On 17/12/12 14:48, Arnout Vandecappelle (Essensium/Mind) wrote: > >> +if BR2_PACKAGE_IMX_LIB > >> +choice > >> + prompt "i.MX platform" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX25_3STACK > >> + bool "imx25-3stack" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX27ADS > >> + bool "imx27ads" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX37_3STACK > >> + bool "imx37-3stack" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX50 > >> + bool "imx50" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX51 > >> + bool "imx51" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX53 > >> + bool "imx53" > >> + > >> +config BR2_PACKAGE_IMX_LIB_PLATFORM_IMX6Q > >> + bool "imx6q" > >> + > >> +endchoice > > Arnout> Here's a second issue that I'd like to get some feedback on: > Arnout> gst-fsl-plugins also uses a PLATFORM definition, but the list of > Arnout> platforms is slightly different: > Arnout> MX28/MX233/MX25/MX27/MX31/MX35/MX37/MX51/MX53/MX50/MX5X/MX6 > > Arnout> Ideally the 'platform' should be defined only once, but where? Or > Arnout> should I add all the platforms to gst-fsl-plugins with a select of the > Arnout> appropriate imx-lib platform? > > We once talked about adding a SoC selection to buildroot, but decided it > would be too much effort to maintain. But of course, maintaining it per package is even more effort... > > Is the gst-fsl-plugins stuff still needed now that the coda driver is in > mainline? Mainline v3.7 only has support for mx27 and mx51. > Arnout> I can only test the mx6q because that's the only one for which > Arnout> I have a board... Build-testing doesn't make a difference > Arnout> because all platforms use the same API. > > I have access to mx28 / mx51 / mx53 / mx6q boards and could do some > testing during christmas. OK, I'll try to post patches before the end of the week. Regards, Arnout -- Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286540 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F