From mboxrd@z Thu Jan 1 00:00:00 1970 From: Johan Sagaert Date: Thu, 17 Sep 2015 01:56:20 +0200 Subject: [Buildroot] =?windows-1252?q?problem_booting_from_ext2_=B5sd_card?= Message-ID: <55FA01A4.5070107@proximus.be> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: buildroot@busybox.net Hi just extracted my rootfs to a ?sd card configured u-boot to boot from it Any idea ? i have a single ext2 partition on a 4GB transcend class 10 card. not sure where to start searching... Tried several cards with equal results. used cfdisk as tool. snip from bootlog usbcore: registered new interface driver usb-storage ci_hdrc ci_hdrc.1: EHCI Host Controller ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected input: 20b8000.kpp as /devices/soc0/soc/2000000.aips-bus/20b8000.kpp/input/input0 input: EP0700M06 as /devices/soc0/soc/2100000.aips-bus/21a8000.i2c/i2c-2/2-0038/input/input1 rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0 snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1 i2c /dev entries driver mxc_v4l2_output v4l2_out: V4L2 device registered as video16 mxc_v4l2_output v4l2_out: V4L2 device registered as video17 imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: no vqmmc regulator found mmc0: no vmmc regulator found mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA mmc1: no vqmmc regulator found mmc1: no vmmc regulator found mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA galcore: clk_get vg clock failed, disable vg! Galcore version 5.0.11.25762 mmc0: new high speed SDHC card at address 59b4 *mmcblk0: mmc0:59b4 USD 3.74 GiB mmcblk0: p1* mxc_vpu 2040000.vpu: VPU initialized usbcore: registered new interface driver usbhid usbhid: USB HID core driver sgtl5000 2-000a: sgtl5000 revision 0x11 2-000a: 1200 mV normal sgtl5000 2-000a: Using internal LDO instead of VDDD imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered failed to disable 1.2 GHz OPP Registering SWP/SWPB emulation handler input: gpio-keys as /devices/soc0/gpio-keys/input/input2 rtc-ds1307 0-0068: setting system clock to 2000-01-01 13:27:11 UTC (946733231) ALSA device list: #0: sgtl5000-audio VFS: Mounted root (ext2 filesystem) on device 179:1. devtmpfs: mounted Freeing unused kernel memory: 252K (80835000 - 80874000) Starting logging: OK Populating /dev using udev: udevd[116]: starting version 3.1.1 random: udevd urandom read with 55 bits of entropy available done Initializing random number generator... done. Starting system message bus: done Starting rpcbind: OK Starting network... fec 2188000.ethernet eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1) IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.23.2) started Sending discover... Sending discover... fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... Sending select for 192.168.1.145... Lease of 192.168.1.145 obtained, lease time 3600 deleting routers adding dns 192.168.1.1 Starting ntpd: OK Starting dropbear sshd: OK Starting inetd : OK /etc/init.d/S80tunetouch: line 16: can't create /sys/bus/i2c/devices/0-0038/threshold: nonexistent directory /etc/init.d/S80tunetouch: line 16: can't create /sys/bus/i2c/devices/0-0038/gain: nonexistent directory /etc/init.d/S80tunetouch: line 16: can't create /sys/bus/i2c/devices/0-0038/report_rate: nonexistent directory Starting mpd: OK Segmentation fault fb-test 1.1.0 (rosetta) fb res 800x480 virtual 800x480, line_len 3200, bpp 32 attempt to access beyond end of device mmcblk0p1: rw=0, want=11524007040, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=33325320632, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=20728214080, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=8149861624, limit=7857074 attempt to access beyond end of device Welcome to Buildrootmmcblk0p1: rw=0, want=26925577088, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=11576436144, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=26035639288, limit=7857074 attempt to access beyond end of device apex_systems login: mmcblk0p1: rw=0, want=30960508736, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=873814192, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=18769465248, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=13401729144, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=8730814792, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=30741356216, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=7043620368, limit=7857074 attempt to access beyond end of device mmcblk0p1: rw=0, want=13247852320, limit=7857074 attempt to access beyond end of device -------------- next part -------------- An HTML attachment was scrubbed... URL: