Re: [PATCH RESEND v9 0/4] dmaengine: dw-edma: Add support for native HDMA

[Serge Semin <fancer.lancer@gmail.com>]

On Thu, Apr 13, 2023 at 11:31:51AM +0800, Cai Huoqing wrote:
> Add support for HDMA NATIVE, as long the IP design has set
> the compatible register map parameter-HDMA_NATIVE,
> which allows compatibility for native HDMA register configuration.
> 
> The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP.
> And the native HDMA registers are different from eDMA,
> so this patch add support for HDMA NATIVE mode.
> 
> HDMA write and read channels operate independently to maximize
> the performance of the HDMA read and write data transfer over
> the link When you configure the HDMA with multiple read channels,
> then it uses a round robin (RR) arbitration scheme to select
> the next read channel to be serviced.The same applies when
> youhave multiple write channels.
> 
> The native HDMA driver also supports a maximum of 16 independent
> channels (8 write + 8 read), which can run simultaneously.
> Both SAR (Source Address Register) and DAR (Destination Address Register)
> are aligned to byte.
> 
> Cai Huoqing (1):
>   dmaengine: dw-edma: Add support for native HDMA
> 
> Cai huoqing (3):
>   dmaengine: dw-edma: Rename dw_edma_core_ops structure to
>     dw_edma_plat_ops
>   dmaengine: dw-edma: Create a new dw_edma_core_ops structure to
>     abstract controller operation
>   dmaengine: dw-edma: Add HDMA DebugFS support
> 
> Tested-by: Serge Semin <fancer.lancer@gmail.com>

Two small notes in the regard of the resubmitted series:
1. On resubmission it would be nice to move the Tested-by tag to all
the patches of the series. Currently neither b4 tool nor patchwork see
it which may cause the tag missing should @Vinod apply the patch by
using these utilities and if he didn't notice it in the cover-letter.
2. Each resubmission even with no functional change implies patchset version
advance. So this patchset was supposed to be v10 with the changelog
describing that it was rebased onto the latest dmaengine-next branch
state.

Just to make sure that my tag won't be missing should this series be
applied:
Tested-by: Serge Semin <fancer.lancer@gmail.com>

-Serge(y)

> 
> v8->v9:
>   [3/4]
>   1.Drop an empty line.
>   [4/4]
>   2.Update commit log.
>   3.Remove unused macro
> 
> v8 link:
>   https://lore.kernel.org/lkml/20230323034944.78357-1-cai.huoqing@linux.dev/
> 
>  drivers/dma/dw-edma/Makefile                 |   8 +-
>  drivers/dma/dw-edma/dw-edma-core.c           |  86 ++----
>  drivers/dma/dw-edma/dw-edma-core.h           |  58 ++++
>  drivers/dma/dw-edma/dw-edma-pcie.c           |   4 +-
>  drivers/dma/dw-edma/dw-edma-v0-core.c        |  85 +++++-
>  drivers/dma/dw-edma/dw-edma-v0-core.h        |  14 +-
>  drivers/dma/dw-edma/dw-hdma-v0-core.c        | 296 +++++++++++++++++++
>  drivers/dma/dw-edma/dw-hdma-v0-core.h        |  17 ++
>  drivers/dma/dw-edma/dw-hdma-v0-debugfs.c     | 170 +++++++++++
>  drivers/dma/dw-edma/dw-hdma-v0-debugfs.h     |  22 ++
>  drivers/dma/dw-edma/dw-hdma-v0-regs.h        | 129 ++++++++
>  drivers/pci/controller/dwc/pcie-designware.c |   2 +-
>  include/linux/dma/edma.h                     |   7 +-
>  13 files changed, 807 insertions(+), 91 deletions(-)
>  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c
>  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h
>  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c
>  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h
>  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.h
> 
> -- 
> 2.34.1
>