[PATCH v6 00/40] ep93xx device tree conversion

[PATCH v6 00/40] ep93xx device tree conversion

[Nikita Shubin via B4 Relay]

No major changes since last version all changes are cometic.

Following patches require attention from Stephen Boyd, as they were converted to aux_dev as suggested:

- ARM: ep93xx: add regmap aux_dev
- clk: ep93xx: add DT support for Cirrus EP93xx

DMA related patches still require Acked or Reviewed tags.

got approval LGTM from Miquel:
- mtd: rawnand: add support for ts72xx
Link: https://lore.kernel.org/lkml/20231004103911.2aa65354@xps-13/

new patches:

ARM: ep93xx:  Add terminator to gpiod_lookup_table
  - fixed terminator in gpiod_lockup_table

So mostly all patches got approval.

Patches should be now formated with '--histogram'

---
Changes in v6:

- clk: ep93xx: add DT support for Cirrus EP93xx
  - s/spin_lock_irqsave()/guard()/
  - refactor index check in ep93xx_mux_set_parent_lock() to something more readable
  - use in_range in ep93xx_mux_set_parent_lock()/ep93xx_ddiv_set_rate()
  - use GENMASK() in ep93xx_ddiv_recalc_rate()
  - comment reserved bit in ep93xx_ddiv_set_rate()
  - move out from loop ClkDiv value assigment
  - some style fixes

Andy, i was i asked to set index of XTALI explicitly, i am not setting ddiv_pdata 
there becouse only XTALI is jnown in advance, and i think setting them in one place is more convenient.

- pinctrl: add a Cirrus ep93xx SoC pin controller
  - drop OF from Kconfig
  - droped linux/of.h include
  - add space to */ where it is applicable
  - add coma in multiline assigment
  - "return NULL" as default case in ep93xx_get_group_name()
  - fixed casting id->driver_data
  - use device_set_of_node_from_dev()
  - use dev_err_probe()

- power: reset: Add a driver for the ep93xx reset
  - drop linux/of.h include

- soc: Add SoC driver for Cirrus ep93xx
  - s/GPL-2.0/GPL-2.0-only/
  - drop linux/kernel.h include
  - + blank line before linux/soc/cirrus/ep93xx.h
  - + blank line after ep93xx_get_soc_rev()
  - + coma for pinctrl_names
  - valid casting to int for of_device_get_match_data() return value

- mtd: rawnand: add support for ts72xx
  - return as part of switch case
  - s/iowrite8/iowrite8_rep/

- net: cirrus: add DT support for Cirrus EP93xx
  - fix header sorting

- dma: cirrus: Convert to DT for Cirrus EP93xx
  - use devm_clk_get
  - use is_slave_direction

Changes in v5:

- gpio: ep93xx: split device in multiple
  - ordered headers
  - use irqd_to_hwirq()
  - s/platform_get_irq()/platform_get_irq_optional()/
 
- [PATCH v4 02/42] ARM: ep93xx: add swlocked prototypes
  - replaced with ARM: ep93xx: add regmap aux_dev

- [PATCH v4 03/42] dt-bindings: clock: Add Cirrus EP93xx
  - fixed identation
  - removed EP93XX_CLK_END
  - and dropped it
  - clock bindings moved to syscon with renaming to cirrus,ep9301-syscon.h

- clk: ep93xx: add DT support for Cirrus EP93xx
  - convert to auxiliary and use parent device tree node
  - moved all clocks except XTALI here
  - used devm version everywhere and *_parent_hw() instead of passing name where it's possible
  - unfortunately devm_clk_hw_register_fixed_rate doesn't have a parent index version

- [PATCH v4 05/42] dt-bindings: pinctrl: Add Cirrus EP93xx
  - "unevaluatedProperties: false" for pins
  - returned "additionalProperties: false" where it was
  - and dropped it

- pinctrl: add a Cirrus ep93xx SoC pin controller
  - sorted includes
  - convert to auxiliary and use parent device tree node

- power: reset: Add a driver for the ep93xx reset
  - convert to auxiliary device

- dt-bindings: soc: Add Cirrus EP93xx
  - dropped all ref to reboot, clk, pinctrl subnodes
  - added pins, as it's now used for pinctrl
  - added #clock-cells, as it's now used for clk

- dt-bindings: pwm: Add Cirrus EP93xx
  - $ref to pwm.yaml
  - fixed 'pwm-cells'
  - s/additionalProperties/unevaluatedProperties/

- soc: Add SoC driver for Cirrus ep93xx
  - removed clocks, they are moved to clk auxiliary driver, as we dropped the clk dt node
  - removed all swlocked exported functions
  - dropped static spinlock
  - added instantiating auxiliary reboot, clk, pinctrl

- dt-bindings: spi: Add Cirrus EP93xx
  - Document DMA support

- spi: ep93xx: add DT support for Cirrus EP93xx
  - dropped CONFIG_OF and SPI/DMA platform data entirely
  - s/master/host/
  - reworked DMA setup so we can use probe defer

- dt-bindings: dma: Add Cirrus EP93xx
  - dropped bindings header (moved ports description to YAML)
  - changed '#dma-cells' to 2, we use port, direction in cells so we can drop platform code completely

- dma: cirrus: add DT support for Cirrus EP93xx
  - dropped platform probing completely
  - dropped struct ep93xx_dma_data replaced with internal struct ep93xx_dma_chan_cfg with port/direction
  - added xlate functions for m2m/m2p
  - we require filters to set dma_cfg before hw_setup

- dt-bindings: ata: Add Cirrus EP93xx
  - Document DMA support 

- ata: pata_ep93xx: add device tree support
  - drop DMA platform header with data
  - use DMA OF so we can defer probing until DMA is up

- ARM: dts: add Cirrus EP93XX SoC .dtsi
- ARM: dts: ep93xx: add ts7250 board
- ARM: dts: ep93xx: Add EDB9302 DT
  - replaced "eclk: clock-controller" to syscon reference
  - replaced "pinctrl: pinctrl" to syscon reference
  - gpios are now "enabled" by default
  - reworked i2s node
  - change all dma nodes and refs

- new additions to I2S
  - Document DMA
  - Document Audio Port usage
  - drop legacy DMA support

- Link to v4: https://lore.kernel.org/r/20230915-ep93xx-v4-0-a1d779dcec10@maquefel.me

Changes in v4:

- gpio: ep93xx: split device in multiple
  - s/generic_handle_irq/generic_handle_domain_irq/
  - s/int offset/irq_hw_number_t offset/ though now it looks a bit odd to me
  - drop i = 0
  - drop 'error'
  - use dev_err_probe withour printing devname once again

dt-bindings: clock: Add Cirrus EP93xx
  - renamed cirrus,ep93xx-clock.h -> cirrus,ep9301-clk.h

clk: ep93xx: add DT support for Cirrus EP93xx
  - drop unused includes
  - use .name only for xtali, pll1, pll2 parents
  - convert // to /*
  - pass clk_parent_data instead of char* clock name

dt-bindings: pinctrl: Add Cirrus EP93xx
  - s/additionalProperties/unevaluatedProperties/

dt-bindings: soc: Add Cirrus EP93xx
  - move syscon to soc directory
  - add vendor prefix
  - make reboot same style as pinctrl, clk
  - use absolute path for ref
  - expand example

soc: Add SoC driver for Cirrus ep93xx
  - s/0xf0000000/GENMASK(31, 28)/
  - s/ret/ep93xx_chip_revision(map)/
  - drop symbol exports
  - convert to platform driver

dt-bindings: rtc: Add Cirrus EP93xx
  - allOf: with $ref to rtc.yaml
  - s/additionalProperties/unevaluatedProperties/

dt-bindings: watchdog: Add Cirrus EP93x
  - drop description
  - reword

power: reset: Add a driver for the ep93xx reset
  - lets use 'GPL-2.0+' instead of '(GPL-2.0)'
  - s/of_device/of/
  - drop mdelay with warning
  - return 0 at the end

net: cirrus: add DT support for Cirrus EP93xx
  - fix leaking np

mtd: nand: add support for ts72xx
  - +bits.h
  - drop comment
  - ok to fwnode_get_next_child_node
  - use goto to put handle and nand and report error

ARM: dts: add Cirrus EP93XX SoC .dtsi
  - add simple-bus for ebi, as we don't require to setup anything
  - add arm,pl011 compatible to uart nodes
  - drop i2c-gpio, as it's isn't used anywhere

ARM: dts: ep93xx: add ts7250 board
  - generic node name for temperature-sensor
  - drop i2c
  - move nand, rtc, watchdog to ebi node
 
- Link to v3: https://lore.kernel.org/r/20230605-ep93xx-v3-0-3d63a5f1103e@maquefel.me

---
Alexander Sverdlin (3):
      ASoC: ep93xx: Drop legacy DMA support
      ARM: dts: ep93xx: Add EDB9302 DT
      ASoC: cirrus: edb93xx: Delete driver

Nikita Shubin (37):
      ARM: ep93xx:  Add terminator to gpiod_lookup_table
      gpio: ep93xx: split device in multiple
      ARM: ep93xx: add regmap aux_dev
      clk: ep93xx: add DT support for Cirrus EP93xx
      pinctrl: add a Cirrus ep93xx SoC pin controller
      power: reset: Add a driver for the ep93xx reset
      dt-bindings: soc: Add Cirrus EP93xx
      soc: Add SoC driver for Cirrus ep93xx
      dt-bindings: dma: Add Cirrus EP93xx
      dma: cirrus: Convert to DT for Cirrus EP93xx
      dt-bindings: watchdog: Add Cirrus EP93x
      watchdog: ep93xx: add DT support for Cirrus EP93xx
      dt-bindings: pwm: Add Cirrus EP93xx
      pwm: ep93xx: add DT support for Cirrus EP93xx
      dt-bindings: spi: Add Cirrus EP93xx
      spi: ep93xx: add DT support for Cirrus EP93xx
      dt-bindings: net: Add Cirrus EP93xx
      net: cirrus: add DT support for Cirrus EP93xx
      dt-bindings: mtd: Add ts7200 nand-controller
      mtd: rawnand: add support for ts72xx
      dt-bindings: ata: Add Cirrus EP93xx
      ata: pata_ep93xx: add device tree support
      dt-bindings: input: Add Cirrus EP93xx keypad
      input: keypad: ep93xx: add DT support for Cirrus EP93xx
      dt-bindings: wdt: Add ts72xx
      wdt: ts72xx: add DT support for ts72xx
      gpio: ep93xx: add DT support for gpio-ep93xx
      ASoC: dt-bindings: ep93xx: Document DMA support
      ASoC: dt-bindings: ep93xx: Document Audio Port support
      ARM: dts: add Cirrus EP93XX SoC .dtsi
      ARM: dts: ep93xx: add ts7250 board
      ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
      pwm: ep93xx: drop legacy pinctrl
      ata: pata_ep93xx: remove legacy pinctrl use
      ARM: ep93xx: delete all boardfiles
      ARM: ep93xx: soc: drop defines
      dma: cirrus: remove platform code

 .../bindings/arm/cirrus/cirrus,ep9301.yaml         |   38 +
 .../bindings/ata/cirrus,ep9312-pata.yaml           |   42 +
 .../bindings/dma/cirrus,ep9301-dma-m2m.yaml        |   84 ++
 .../bindings/dma/cirrus,ep9301-dma-m2p.yaml        |  144 ++
 .../bindings/input/cirrus,ep9307-keypad.yaml       |   87 ++
 .../devicetree/bindings/mtd/technologic,nand.yaml  |   45 +
 .../devicetree/bindings/net/cirrus,ep9301-eth.yaml |   59 +
 .../devicetree/bindings/pwm/cirrus,ep9301-pwm.yaml |   53 +
 .../bindings/soc/cirrus/cirrus,ep9301-syscon.yaml  |   94 ++
 .../bindings/sound/cirrus,ep9301-i2s.yaml          |   16 +
 .../devicetree/bindings/spi/cirrus,ep9301-spi.yaml |   70 +
 .../bindings/watchdog/cirrus,ep9301-wdt.yaml       |   42 +
 .../bindings/watchdog/technologic,ts7200-wdt.yaml  |   45 +
 arch/arm/Makefile                                  |    1 -
 arch/arm/boot/dts/cirrus/Makefile                  |    4 +
 arch/arm/boot/dts/cirrus/ep93xx-bk3.dts            |  126 ++
 arch/arm/boot/dts/cirrus/ep93xx-edb9302.dts        |  182 +++
 arch/arm/boot/dts/cirrus/ep93xx-ts7250.dts         |  145 ++
 arch/arm/boot/dts/cirrus/ep93xx.dtsi               |  441 ++++++
 arch/arm/mach-ep93xx/Kconfig                       |   20 +-
 arch/arm/mach-ep93xx/Makefile                      |   11 -
 arch/arm/mach-ep93xx/clock.c                       |  733 ----------
 arch/arm/mach-ep93xx/core.c                        | 1017 --------------
 arch/arm/mach-ep93xx/dma.c                         |  114 --
 arch/arm/mach-ep93xx/edb93xx.c                     |  344 -----
 arch/arm/mach-ep93xx/ep93xx-regs.h                 |   38 -
 arch/arm/mach-ep93xx/gpio-ep93xx.h                 |  111 --
 arch/arm/mach-ep93xx/hardware.h                    |   25 -
 arch/arm/mach-ep93xx/irqs.h                        |   76 --
 arch/arm/mach-ep93xx/platform.h                    |   42 -
 arch/arm/mach-ep93xx/soc.h                         |  212 ---
 arch/arm/mach-ep93xx/timer-ep93xx.c                |  143 --
 arch/arm/mach-ep93xx/ts72xx.c                      |  422 ------
 arch/arm/mach-ep93xx/ts72xx.h                      |   94 --
 arch/arm/mach-ep93xx/vision_ep9307.c               |  311 -----
 drivers/ata/pata_ep93xx.c                          |  106 +-
 drivers/clk/Kconfig                                |    8 +
 drivers/clk/Makefile                               |    1 +
 drivers/clk/clk-ep93xx.c                           |  849 ++++++++++++
 drivers/dma/ep93xx_dma.c                           |  286 +++-
 drivers/gpio/gpio-ep93xx.c                         |  345 ++---
 drivers/input/keyboard/ep93xx_keypad.c             |   74 +-
 drivers/mtd/nand/raw/Kconfig                       |    7 +
 drivers/mtd/nand/raw/Makefile                      |    1 +
 drivers/mtd/nand/raw/technologic-nand-controller.c |  220 +++
 drivers/net/ethernet/cirrus/ep93xx_eth.c           |   63 +-
 drivers/pinctrl/Kconfig                            |    7 +
 drivers/pinctrl/Makefile                           |    1 +
 drivers/pinctrl/pinctrl-ep93xx.c                   | 1430 ++++++++++++++++++++
 drivers/power/reset/Kconfig                        |   10 +
 drivers/power/reset/Makefile                       |    1 +
 drivers/power/reset/ep93xx-restart.c               |   80 ++
 drivers/pwm/pwm-ep93xx.c                           |   26 +-
 drivers/soc/Kconfig                                |    1 +
 drivers/soc/Makefile                               |    1 +
 drivers/soc/cirrus/Kconfig                         |   13 +
 drivers/soc/cirrus/Makefile                        |    2 +
 drivers/soc/cirrus/soc-ep93xx.c                    |  247 ++++
 drivers/spi/spi-ep93xx.c                           |   68 +-
 drivers/watchdog/ep93xx_wdt.c                      |    8 +
 drivers/watchdog/ts72xx_wdt.c                      |    8 +
 include/dt-bindings/clock/cirrus,ep9301-syscon.h   |   46 +
 include/linux/platform_data/dma-ep93xx.h           |   94 --
 include/linux/platform_data/eth-ep93xx.h           |   10 -
 include/linux/platform_data/keypad-ep93xx.h        |   32 -
 include/linux/platform_data/spi-ep93xx.h           |   15 -
 include/linux/soc/cirrus/ep93xx.h                  |   47 +-
 sound/soc/cirrus/Kconfig                           |    9 -
 sound/soc/cirrus/Makefile                          |    4 -
 sound/soc/cirrus/edb93xx.c                         |  117 --
 sound/soc/cirrus/ep93xx-i2s.c                      |   19 -
 sound/soc/cirrus/ep93xx-pcm.c                      |   19 +-
 72 files changed, 5192 insertions(+), 4514 deletions(-)
---
base-commit: 26aff849438cebcd05f1a647390c4aa700d5c0f1
change-id: 20230605-ep93xx-01c76317e2d2

Best regards,
-- 
Nikita Shubin <nikita.shubin@maquefel.me>

[PATCH v6 09/40] dt-bindings: dma: Add Cirrus EP93xx

[Nikita Shubin via B4 Relay]

From: Nikita Shubin <nikita.shubin@maquefel.me>

Add YAML bindings for ep93xx SoC DMA.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
---
 .../bindings/dma/cirrus,ep9301-dma-m2m.yaml        |  84 ++++++++++++
 .../bindings/dma/cirrus,ep9301-dma-m2p.yaml        | 144 +++++++++++++++++++++
 2 files changed, 228 insertions(+)

diff --git a/Documentation/devicetree/bindings/dma/cirrus,ep9301-dma-m2m.yaml b/Documentation/devicetree/bindings/dma/cirrus,ep9301-dma-m2m.yaml
new file mode 100644
index 000000000000..871b76ddf90f
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/cirrus,ep9301-dma-m2m.yaml
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/cirrus,ep9301-dma-m2m.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic ep93xx SoC DMA controller
+
+maintainers:
+  - Alexander Sverdlin <alexander.sverdlin@gmail.com>
+  - Nikita Shubin <nikita.shubin@maquefel.me>
+
+allOf:
+  - $ref: dma-controller.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - const: cirrus,ep9301-dma-m2m
+      - items:
+          - enum:
+              - cirrus,ep9302-dma-m2m
+              - cirrus,ep9307-dma-m2m
+              - cirrus,ep9312-dma-m2m
+              - cirrus,ep9315-dma-m2m
+          - const: cirrus,ep9301-dma-m2m
+
+  reg:
+    items:
+      - description: m2m0 channel registers
+      - description: m2m1 channel registers
+
+  clocks:
+    items:
+      - description: m2m0 channel gate clock
+      - description: m2m1 channel gate clock
+
+  clock-names:
+    items:
+      - const: m2m0
+      - const: m2m1
+
+  interrupts:
+    items:
+      - description: m2m0 channel interrupt
+      - description: m2m1 channel interrupt
+
+  '#dma-cells':
+    const: 2
+    description: |
+      The first cell is the unique device channel number as indicated by this
+      table for ep93xx:
+
+      10: SPI controller
+      11: IDE controller
+
+      The second cell is the DMA direction line number:
+
+      1: Memory to device
+      2: Device to memory
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/cirrus,ep9301-syscon.h>
+    dma-controller@80000100 {
+        compatible = "cirrus,ep9301-dma-m2m";
+        reg = <0x80000100 0x0040>,
+              <0x80000140 0x0040>;
+        clocks = <&syscon EP93XX_CLK_M2M0>,
+                 <&syscon EP93XX_CLK_M2M1>;
+        clock-names = "m2m0", "m2m1";
+        interrupt-parent = <&vic0>;
+        interrupts = <17>, <18>;
+        #dma-cells = <2>;
+    };
diff --git a/Documentation/devicetree/bindings/dma/cirrus,ep9301-dma-m2p.yaml b/Documentation/devicetree/bindings/dma/cirrus,ep9301-dma-m2p.yaml
new file mode 100644
index 000000000000..d14c31553543
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/cirrus,ep9301-dma-m2p.yaml
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/cirrus,ep9301-dma-m2p.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic ep93xx SoC M2P DMA controller
+
+maintainers:
+  - Alexander Sverdlin <alexander.sverdlin@gmail.com>
+  - Nikita Shubin <nikita.shubin@maquefel.me>
+
+allOf:
+  - $ref: dma-controller.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - const: cirrus,ep9301-dma-m2p
+      - items:
+          - enum:
+              - cirrus,ep9302-dma-m2p
+              - cirrus,ep9307-dma-m2p
+              - cirrus,ep9312-dma-m2p
+              - cirrus,ep9315-dma-m2p
+          - const: cirrus,ep9301-dma-m2p
+
+  reg:
+    items:
+      - description: m2p0 channel registers
+      - description: m2p1 channel registers
+      - description: m2p2 channel registers
+      - description: m2p3 channel registers
+      - description: m2p4 channel registers
+      - description: m2p5 channel registers
+      - description: m2p6 channel registers
+      - description: m2p7 channel registers
+      - description: m2p8 channel registers
+      - description: m2p9 channel registers
+
+  clocks:
+    items:
+      - description: m2p0 channel gate clock
+      - description: m2p1 channel gate clock
+      - description: m2p2 channel gate clock
+      - description: m2p3 channel gate clock
+      - description: m2p4 channel gate clock
+      - description: m2p5 channel gate clock
+      - description: m2p6 channel gate clock
+      - description: m2p7 channel gate clock
+      - description: m2p8 channel gate clock
+      - description: m2p9 channel gate clock
+
+  clock-names:
+    items:
+      - const: m2p0
+      - const: m2p1
+      - const: m2p2
+      - const: m2p3
+      - const: m2p4
+      - const: m2p5
+      - const: m2p6
+      - const: m2p7
+      - const: m2p8
+      - const: m2p9
+
+  interrupts:
+    items:
+      - description: m2p0 channel interrupt
+      - description: m2p1 channel interrupt
+      - description: m2p2 channel interrupt
+      - description: m2p3 channel interrupt
+      - description: m2p4 channel interrupt
+      - description: m2p5 channel interrupt
+      - description: m2p6 channel interrupt
+      - description: m2p7 channel interrupt
+      - description: m2p8 channel interrupt
+      - description: m2p9 channel interrupt
+
+  '#dma-cells':
+    const: 2
+    description: |
+      The first cell is the unique device channel number as indicated by this
+      table for ep93xx:
+
+      0: I2S channel 1
+      1: I2S channel 2 (unused)
+      2: AC97 channel 1 (unused)
+      3: AC97 channel 2 (unused)
+      4: AC97 channel 3 (unused)
+      5: I2S channel 3 (unused)
+      6: UART1 (unused)
+      7: UART2 (unused)
+      8: UART3 (unused)
+      9: IRDA (unused)
+
+      The second cell is the DMA direction line number:
+
+      1: Memory to device
+      2: Device to memory
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/cirrus,ep9301-syscon.h>
+    dma-controller@80000000 {
+        compatible = "cirrus,ep9301-dma-m2p";
+        reg = <0x80000000 0x0040>,
+              <0x80000040 0x0040>,
+              <0x80000080 0x0040>,
+              <0x800000c0 0x0040>,
+              <0x80000240 0x0040>,
+              <0x80000200 0x0040>,
+              <0x800002c0 0x0040>,
+              <0x80000280 0x0040>,
+              <0x80000340 0x0040>,
+              <0x80000300 0x0040>;
+        clocks = <&syscon EP93XX_CLK_M2P0>,
+                 <&syscon EP93XX_CLK_M2P1>,
+                 <&syscon EP93XX_CLK_M2P2>,
+                 <&syscon EP93XX_CLK_M2P3>,
+                 <&syscon EP93XX_CLK_M2P4>,
+                 <&syscon EP93XX_CLK_M2P5>,
+                 <&syscon EP93XX_CLK_M2P6>,
+                 <&syscon EP93XX_CLK_M2P7>,
+                 <&syscon EP93XX_CLK_M2P8>,
+                 <&syscon EP93XX_CLK_M2P9>;
+        clock-names = "m2p0", "m2p1",
+                      "m2p2", "m2p3",
+                      "m2p4", "m2p5",
+                      "m2p6", "m2p7",
+                      "m2p8", "m2p9";
+        interrupt-parent = <&vic0>;
+        interrupts = <7>, <8>, <9>, <10>, <11>, <12>, <13>, <14>, <15>, <16>;
+        #dma-cells = <2>;
+    };

-- 
2.41.0

[PATCH v6 10/40] dma: cirrus: Convert to DT for Cirrus EP93xx

[Nikita Shubin via B4 Relay]

From: Nikita Shubin <nikita.shubin@maquefel.me>

Convert Cirrus EP93xx DMA to device tree usage:

- add OF ID match table with data
- add of_probe for device tree
- add xlate for m2m/m2p
- drop subsys_initcall code
- drop platform probe
- drop platform structs usage

From now only it supports only device tree probing.

Co-developed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
---
 drivers/dma/ep93xx_dma.c                 | 238 ++++++++++++++++++++++++-------
 include/linux/platform_data/dma-ep93xx.h |   6 +
 2 files changed, 191 insertions(+), 53 deletions(-)

diff --git a/drivers/dma/ep93xx_dma.c b/drivers/dma/ep93xx_dma.c
index d6c60635e90d..b7dd8361f490 100644
--- a/drivers/dma/ep93xx_dma.c
+++ b/drivers/dma/ep93xx_dma.c
@@ -20,6 +20,8 @@
 #include <linux/dmaengine.h>
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
+#include <linux/of_dma.h>
+#include <linux/overflow.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 
@@ -104,6 +106,11 @@
 #define DMA_MAX_CHAN_BYTES		0xffff
 #define DMA_MAX_CHAN_DESCRIPTORS	32
 
+enum ep93xx_dma_type {
+	M2P_DMA,
+	M2M_DMA,
+};
+
 struct ep93xx_dma_engine;
 static int ep93xx_dma_slave_config_write(struct dma_chan *chan,
 					 enum dma_transfer_direction dir,
@@ -129,11 +136,17 @@ struct ep93xx_dma_desc {
 	struct list_head		node;
 };
 
+struct ep93xx_dma_chan_cfg {
+	u8				port;
+	enum dma_transfer_direction	dir;
+};
+
 /**
  * struct ep93xx_dma_chan - an EP93xx DMA M2P/M2M channel
  * @chan: dmaengine API channel
  * @edma: pointer to the engine device
  * @regs: memory mapped registers
+ * @dma_cfg: channel number, direction
  * @irq: interrupt number of the channel
  * @clk: clock used by this channel
  * @tasklet: channel specific tasklet used for callbacks
@@ -157,14 +170,12 @@ struct ep93xx_dma_desc {
  * descriptor in the chain. When a descriptor is moved to the @active queue,
  * the first and chained descriptors are flattened into a single list.
  *
- * @chan.private holds pointer to &struct ep93xx_dma_data which contains
- * necessary channel configuration information. For memcpy channels this must
- * be %NULL.
  */
 struct ep93xx_dma_chan {
 	struct dma_chan			chan;
 	const struct ep93xx_dma_engine	*edma;
 	void __iomem			*regs;
+	struct ep93xx_dma_chan_cfg	dma_cfg;
 	int				irq;
 	struct clk			*clk;
 	struct tasklet_struct		tasklet;
@@ -216,6 +227,11 @@ struct ep93xx_dma_engine {
 	struct ep93xx_dma_chan	channels[] __counted_by(num_channels);
 };
 
+struct ep93xx_edma_data {
+	u32	id;
+	size_t	num_channels;
+};
+
 static inline struct device *chan2dev(struct ep93xx_dma_chan *edmac)
 {
 	return &edmac->chan.dev->device;
@@ -318,10 +334,9 @@ static void m2p_set_control(struct ep93xx_dma_chan *edmac, u32 control)
 
 static int m2p_hw_setup(struct ep93xx_dma_chan *edmac)
 {
-	struct ep93xx_dma_data *data = edmac->chan.private;
 	u32 control;
 
-	writel(data->port & 0xf, edmac->regs + M2P_PPALLOC);
+	writel(edmac->dma_cfg.port & 0xf, edmac->regs + M2P_PPALLOC);
 
 	control = M2P_CONTROL_CH_ERROR_INT | M2P_CONTROL_ICE
 		| M2P_CONTROL_ENABLE;
@@ -458,16 +473,15 @@ static int m2p_hw_interrupt(struct ep93xx_dma_chan *edmac)
 
 static int m2m_hw_setup(struct ep93xx_dma_chan *edmac)
 {
-	const struct ep93xx_dma_data *data = edmac->chan.private;
 	u32 control = 0;
 
-	if (!data) {
+	if (edmac->dma_cfg.dir == DMA_MEM_TO_MEM) {
 		/* This is memcpy channel, nothing to configure */
 		writel(control, edmac->regs + M2M_CONTROL);
 		return 0;
 	}
 
-	switch (data->port) {
+	switch (edmac->dma_cfg.port) {
 	case EP93XX_DMA_SSP:
 		/*
 		 * This was found via experimenting - anything less than 5
@@ -477,7 +491,7 @@ static int m2m_hw_setup(struct ep93xx_dma_chan *edmac)
 		control = (5 << M2M_CONTROL_PWSC_SHIFT);
 		control |= M2M_CONTROL_NO_HDSK;
 
-		if (data->direction == DMA_MEM_TO_DEV) {
+		if (edmac->dma_cfg.dir == DMA_MEM_TO_DEV) {
 			control |= M2M_CONTROL_DAH;
 			control |= M2M_CONTROL_TM_TX;
 			control |= M2M_CONTROL_RSS_SSPTX;
@@ -493,7 +507,7 @@ static int m2m_hw_setup(struct ep93xx_dma_chan *edmac)
 		 * This IDE part is totally untested. Values below are taken
 		 * from the EP93xx Users's Guide and might not be correct.
 		 */
-		if (data->direction == DMA_MEM_TO_DEV) {
+		if (edmac->dma_cfg.dir == DMA_MEM_TO_DEV) {
 			/* Worst case from the UG */
 			control = (3 << M2M_CONTROL_PWSC_SHIFT);
 			control |= M2M_CONTROL_DAH;
@@ -548,7 +562,6 @@ static void m2m_fill_desc(struct ep93xx_dma_chan *edmac)
 
 static void m2m_hw_submit(struct ep93xx_dma_chan *edmac)
 {
-	struct ep93xx_dma_data *data = edmac->chan.private;
 	u32 control = readl(edmac->regs + M2M_CONTROL);
 
 	/*
@@ -574,7 +587,7 @@ static void m2m_hw_submit(struct ep93xx_dma_chan *edmac)
 	control |= M2M_CONTROL_ENABLE;
 	writel(control, edmac->regs + M2M_CONTROL);
 
-	if (!data) {
+	if (edmac->dma_cfg.dir == DMA_MEM_TO_MEM) {
 		/*
 		 * For memcpy channels the software trigger must be asserted
 		 * in order to start the memcpy operation.
@@ -636,7 +649,7 @@ static int m2m_hw_interrupt(struct ep93xx_dma_chan *edmac)
 		 */
 		if (ep93xx_dma_advance_active(edmac)) {
 			m2m_fill_desc(edmac);
-			if (done && !edmac->chan.private) {
+			if (done && edmac->dma_cfg.dir == DMA_MEM_TO_MEM) {
 				/* Software trigger for memcpy channel */
 				control = readl(edmac->regs + M2M_CONTROL);
 				control |= M2M_CONTROL_START;
@@ -867,25 +880,22 @@ static dma_cookie_t ep93xx_dma_tx_submit(struct dma_async_tx_descriptor *tx)
 static int ep93xx_dma_alloc_chan_resources(struct dma_chan *chan)
 {
 	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
-	struct ep93xx_dma_data *data = chan->private;
 	const char *name = dma_chan_name(chan);
 	int ret, i;
 
 	/* Sanity check the channel parameters */
 	if (!edmac->edma->m2m) {
-		if (!data)
+		if (edmac->dma_cfg.port < EP93XX_DMA_I2S1 ||
+		    edmac->dma_cfg.port > EP93XX_DMA_IRDA)
 			return -EINVAL;
-		if (data->port < EP93XX_DMA_I2S1 ||
-		    data->port > EP93XX_DMA_IRDA)
-			return -EINVAL;
-		if (data->direction != ep93xx_dma_chan_direction(chan))
+		if (edmac->dma_cfg.dir != ep93xx_dma_chan_direction(chan))
 			return -EINVAL;
 	} else {
-		if (data) {
-			switch (data->port) {
+		if (edmac->dma_cfg.dir != DMA_MEM_TO_MEM) {
+			switch (edmac->dma_cfg.port) {
 			case EP93XX_DMA_SSP:
 			case EP93XX_DMA_IDE:
-				if (!is_slave_direction(data->direction))
+				if (!is_slave_direction(edmac->dma_cfg.dir))
 					return -EINVAL;
 				break;
 			default:
@@ -894,9 +904,6 @@ static int ep93xx_dma_alloc_chan_resources(struct dma_chan *chan)
 		}
 	}
 
-	if (data && data->name)
-		name = data->name;
-
 	ret = clk_prepare_enable(edmac->clk);
 	if (ret)
 		return ret;
@@ -1315,35 +1322,51 @@ static void ep93xx_dma_issue_pending(struct dma_chan *chan)
 	ep93xx_dma_advance_work(to_ep93xx_dma_chan(chan));
 }
 
-static int __init ep93xx_dma_probe(struct platform_device *pdev)
+static struct ep93xx_dma_engine *ep93xx_dma_of_probe(struct platform_device *pdev)
 {
-	struct ep93xx_dma_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	const struct ep93xx_edma_data *data;
+	struct device *dev = &pdev->dev;
 	struct ep93xx_dma_engine *edma;
 	struct dma_device *dma_dev;
-	int ret, i;
+	char dma_clk_name[5];
+	int i;
 
-	edma = kzalloc(struct_size(edma, channels, pdata->num_channels), GFP_KERNEL);
+	data = device_get_match_data(dev);
+	if (!data)
+		return ERR_PTR(dev_err_probe(dev, -ENODEV, "No device match found\n"));
+
+	edma = devm_kzalloc(dev, struct_size(edma, channels, data->num_channels),
+			    GFP_KERNEL);
 	if (!edma)
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
 
+	edma->m2m = data->id;
+	edma->num_channels = data->num_channels;
 	dma_dev = &edma->dma_dev;
-	edma->m2m = platform_get_device_id(pdev)->driver_data;
-	edma->num_channels = pdata->num_channels;
 
 	INIT_LIST_HEAD(&dma_dev->channels);
-	for (i = 0; i < pdata->num_channels; i++) {
-		const struct ep93xx_dma_chan_data *cdata = &pdata->channels[i];
+	for (i = 0; i < edma->num_channels; i++) {
 		struct ep93xx_dma_chan *edmac = &edma->channels[i];
 
 		edmac->chan.device = dma_dev;
-		edmac->regs = cdata->base;
-		edmac->irq = cdata->irq;
+		edmac->regs = devm_platform_ioremap_resource(pdev, i);
+		if (IS_ERR(edmac->regs))
+			return edmac->regs;
+
+		edmac->irq = fwnode_irq_get(dev_fwnode(dev), i);
+		if (edmac->irq < 0)
+			return ERR_PTR(edmac->irq);
+
 		edmac->edma = edma;
 
-		edmac->clk = clk_get(NULL, cdata->name);
+		if (edma->m2m)
+			sprintf(dma_clk_name, "m2m%u", i);
+		else
+			sprintf(dma_clk_name, "m2p%u", i);
+
+		edmac->clk = devm_clk_get(dev, dma_clk_name);
 		if (IS_ERR(edmac->clk)) {
-			dev_warn(&pdev->dev, "failed to get clock for %s\n",
-				 cdata->name);
+			dev_warn(dev, "failed to get clock\n");
 			continue;
 		}
 
@@ -1357,6 +1380,92 @@ static int __init ep93xx_dma_probe(struct platform_device *pdev)
 			      &dma_dev->channels);
 	}
 
+	return edma;
+}
+
+static bool ep93xx_m2p_dma_filter(struct dma_chan *chan, void *filter_param)
+{
+	struct ep93xx_dma_chan *echan = to_ep93xx_dma_chan(chan);
+	struct ep93xx_dma_chan_cfg *cfg = filter_param;
+
+	if (cfg->dir == ep93xx_dma_chan_direction(chan)) {
+		echan->dma_cfg = *cfg;
+		return true;
+	}
+
+	return false;
+}
+
+static struct dma_chan *ep93xx_m2p_dma_of_xlate(struct of_phandle_args *dma_spec,
+					    struct of_dma *ofdma)
+{
+	struct ep93xx_dma_engine *edma = ofdma->of_dma_data;
+	dma_cap_mask_t mask = edma->dma_dev.cap_mask;
+	struct ep93xx_dma_chan_cfg dma_cfg;
+	u8 port = dma_spec->args[0];
+	u8 direction = dma_spec->args[1];
+
+	if (port > EP93XX_DMA_IRDA)
+		return NULL;
+
+	if (!is_slave_direction(direction))
+		return NULL;
+
+
+	dma_cfg.port = port;
+	dma_cfg.dir = direction;
+
+	return __dma_request_channel(&mask, ep93xx_m2p_dma_filter, &dma_cfg, ofdma->of_node);
+}
+
+static bool ep93xx_m2m_dma_filter(struct dma_chan *chan, void *filter_param)
+{
+	struct ep93xx_dma_chan *echan = to_ep93xx_dma_chan(chan);
+	struct ep93xx_dma_chan_cfg *cfg = filter_param;
+
+	echan->dma_cfg = *cfg;
+
+	return true;
+}
+
+static struct dma_chan *ep93xx_m2m_dma_of_xlate(struct of_phandle_args *dma_spec,
+					    struct of_dma *ofdma)
+{
+	struct ep93xx_dma_engine *edma = ofdma->of_dma_data;
+	dma_cap_mask_t mask = edma->dma_dev.cap_mask;
+	struct ep93xx_dma_chan_cfg dma_cfg;
+	u8 port = dma_spec->args[0];
+	u8 direction = dma_spec->args[1];
+
+	switch (port) {
+	case EP93XX_DMA_SSP:
+	case EP93XX_DMA_IDE:
+		break;
+	default:
+		return NULL;
+	}
+
+	if (!is_slave_direction(direction))
+		return NULL;
+
+	dma_cfg.port = port;
+	dma_cfg.dir = direction;
+
+	return __dma_request_channel(&mask, ep93xx_m2m_dma_filter, &dma_cfg, ofdma->of_node);
+}
+
+static int ep93xx_dma_probe(struct platform_device *pdev)
+{
+	struct ep93xx_dma_engine *edma;
+	struct dma_device *dma_dev;
+	int ret;
+
+	edma = ep93xx_dma_of_probe(pdev);
+	if (!edma)
+		return PTR_ERR(edma);
+
+	dma_dev = &edma->dma_dev;
+
 	dma_cap_zero(dma_dev->cap_mask);
 	dma_cap_set(DMA_SLAVE, dma_dev->cap_mask);
 	dma_cap_set(DMA_CYCLIC, dma_dev->cap_mask);
@@ -1393,21 +1502,46 @@ static int __init ep93xx_dma_probe(struct platform_device *pdev)
 	}
 
 	ret = dma_async_device_register(dma_dev);
-	if (unlikely(ret)) {
-		for (i = 0; i < edma->num_channels; i++) {
-			struct ep93xx_dma_chan *edmac = &edma->channels[i];
-			if (!IS_ERR_OR_NULL(edmac->clk))
-				clk_put(edmac->clk);
-		}
-		kfree(edma);
+	if (ret)
+		return ret;
+
+	if (edma->m2m) {
+		ret = of_dma_controller_register(pdev->dev.of_node, ep93xx_m2m_dma_of_xlate,
+						 edma);
 	} else {
-		dev_info(dma_dev->dev, "EP93xx M2%s DMA ready\n",
-			 edma->m2m ? "M" : "P");
+		ret = of_dma_controller_register(pdev->dev.of_node, ep93xx_m2p_dma_of_xlate,
+						 edma);
 	}
+	if (ret)
+		goto err_dma_unregister;
+
+	dev_info(dma_dev->dev, "EP93xx M2%s DMA ready\n", edma->m2m ? "M" : "P");
+
+	return 0;
+
+err_dma_unregister:
+	dma_async_device_unregister(dma_dev);
 
 	return ret;
 }
 
+static const struct ep93xx_edma_data edma_m2p = {
+	.id = M2P_DMA,
+	.num_channels = 10,
+};
+
+static const struct ep93xx_edma_data edma_m2m = {
+	.id = M2M_DMA,
+	.num_channels = 2,
+};
+
+static const struct of_device_id ep93xx_dma_of_ids[] = {
+	{ .compatible = "cirrus,ep9301-dma-m2p", .data = &edma_m2p },
+	{ .compatible = "cirrus,ep9301-dma-m2m", .data = &edma_m2m },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ep93xx_dma_of_ids);
+
 static const struct platform_device_id ep93xx_dma_driver_ids[] = {
 	{ "ep93xx-dma-m2p", 0 },
 	{ "ep93xx-dma-m2m", 1 },
@@ -1417,15 +1551,13 @@ static const struct platform_device_id ep93xx_dma_driver_ids[] = {
 static struct platform_driver ep93xx_dma_driver = {
 	.driver		= {
 		.name	= "ep93xx-dma",
+		.of_match_table = ep93xx_dma_of_ids,
 	},
 	.id_table	= ep93xx_dma_driver_ids,
+	.probe		= ep93xx_dma_probe,
 };
 
-static int __init ep93xx_dma_module_init(void)
-{
-	return platform_driver_probe(&ep93xx_dma_driver, ep93xx_dma_probe);
-}
-subsys_initcall(ep93xx_dma_module_init);
+module_platform_driver(ep93xx_dma_driver);
 
 MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
 MODULE_DESCRIPTION("EP93xx DMA driver");
diff --git a/include/linux/platform_data/dma-ep93xx.h b/include/linux/platform_data/dma-ep93xx.h
index eb9805bb3fe8..67d65f1cb564 100644
--- a/include/linux/platform_data/dma-ep93xx.h
+++ b/include/linux/platform_data/dma-ep93xx.h
@@ -2,6 +2,9 @@
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H
 
+#include <linux/device.h>
+#include <linux/property.h>
+#include <linux/string.h>
 #include <linux/types.h>
 #include <linux/dmaengine.h>
 #include <linux/dma-mapping.h>
@@ -70,6 +73,9 @@ struct ep93xx_dma_platform_data {
 
 static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
 {
+	if (device_is_compatible(chan->device->dev, "cirrus,ep9301-dma-m2p"))
+		return true;
+
 	return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
 }
 

-- 
2.41.0

[PATCH v6 40/40] dma: cirrus: remove platform code

[Nikita Shubin via B4 Relay]

From: Nikita Shubin <nikita.shubin@maquefel.me>

Remove DMA platform header, from now on we use device tree for dma
clients.

Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
---
 drivers/dma/ep93xx_dma.c                 |  48 ++++++++++++++-
 include/linux/platform_data/dma-ep93xx.h | 100 -------------------------------
 2 files changed, 46 insertions(+), 102 deletions(-)

diff --git a/drivers/dma/ep93xx_dma.c b/drivers/dma/ep93xx_dma.c
index b7dd8361f490..d11cd11f32bf 100644
--- a/drivers/dma/ep93xx_dma.c
+++ b/drivers/dma/ep93xx_dma.c
@@ -17,6 +17,7 @@
 #include <linux/clk.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
@@ -25,8 +26,6 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 
-#include <linux/platform_data/dma-ep93xx.h>
-
 #include "dmaengine.h"
 
 /* M2P registers */
@@ -106,6 +105,26 @@
 #define DMA_MAX_CHAN_BYTES		0xffff
 #define DMA_MAX_CHAN_DESCRIPTORS	32
 
+/*
+ * M2P channels.
+ *
+ * Note that these values are also directly used for setting the PPALLOC
+ * register.
+ */
+#define EP93XX_DMA_I2S1			0
+#define EP93XX_DMA_I2S2			1
+#define EP93XX_DMA_AAC1			2
+#define EP93XX_DMA_AAC2			3
+#define EP93XX_DMA_AAC3			4
+#define EP93XX_DMA_I2S3			5
+#define EP93XX_DMA_UART1		6
+#define EP93XX_DMA_UART2		7
+#define EP93XX_DMA_UART3		8
+#define EP93XX_DMA_IRDA			9
+/* M2M channels */
+#define EP93XX_DMA_SSP			10
+#define EP93XX_DMA_IDE			11
+
 enum ep93xx_dma_type {
 	M2P_DMA,
 	M2M_DMA,
@@ -242,6 +261,31 @@ static struct ep93xx_dma_chan *to_ep93xx_dma_chan(struct dma_chan *chan)
 	return container_of(chan, struct ep93xx_dma_chan, chan);
 }
 
+static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
+{
+	if (device_is_compatible(chan->device->dev, "cirrus,ep9301-dma-m2p"))
+		return true;
+
+	return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
+}
+
+/*
+ * ep93xx_dma_chan_direction - returns direction the channel can be used
+ *
+ * This function can be used in filter functions to find out whether the
+ * channel supports given DMA direction. Only M2P channels have such
+ * limitation, for M2M channels the direction is configurable.
+ */
+static inline enum dma_transfer_direction
+ep93xx_dma_chan_direction(struct dma_chan *chan)
+{
+	if (!ep93xx_dma_chan_is_m2p(chan))
+		return DMA_TRANS_NONE;
+
+	/* even channels are for TX, odd for RX */
+	return (chan->chan_id % 2 == 0) ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
+}
+
 /**
  * ep93xx_dma_set_active - set new active descriptor chain
  * @edmac: channel
diff --git a/include/linux/platform_data/dma-ep93xx.h b/include/linux/platform_data/dma-ep93xx.h
deleted file mode 100644
index 67d65f1cb564..000000000000
--- a/include/linux/platform_data/dma-ep93xx.h
+++ /dev/null
@@ -1,100 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H
-
-#include <linux/device.h>
-#include <linux/property.h>
-#include <linux/string.h>
-#include <linux/types.h>
-#include <linux/dmaengine.h>
-#include <linux/dma-mapping.h>
-
-/*
- * M2P channels.
- *
- * Note that these values are also directly used for setting the PPALLOC
- * register.
- */
-#define EP93XX_DMA_I2S1		0
-#define EP93XX_DMA_I2S2		1
-#define EP93XX_DMA_AAC1		2
-#define EP93XX_DMA_AAC2		3
-#define EP93XX_DMA_AAC3		4
-#define EP93XX_DMA_I2S3		5
-#define EP93XX_DMA_UART1	6
-#define EP93XX_DMA_UART2	7
-#define EP93XX_DMA_UART3	8
-#define EP93XX_DMA_IRDA		9
-/* M2M channels */
-#define EP93XX_DMA_SSP		10
-#define EP93XX_DMA_IDE		11
-
-/**
- * struct ep93xx_dma_data - configuration data for the EP93xx dmaengine
- * @port: peripheral which is requesting the channel
- * @direction: TX/RX channel
- * @name: optional name for the channel, this is displayed in /proc/interrupts
- *
- * This information is passed as private channel parameter in a filter
- * function. Note that this is only needed for slave/cyclic channels.  For
- * memcpy channels %NULL data should be passed.
- */
-struct ep93xx_dma_data {
-	int				port;
-	enum dma_transfer_direction	direction;
-	const char			*name;
-};
-
-/**
- * struct ep93xx_dma_chan_data - platform specific data for a DMA channel
- * @name: name of the channel, used for getting the right clock for the channel
- * @base: mapped registers
- * @irq: interrupt number used by this channel
- */
-struct ep93xx_dma_chan_data {
-	const char			*name;
-	void __iomem			*base;
-	int				irq;
-};
-
-/**
- * struct ep93xx_dma_platform_data - platform data for the dmaengine driver
- * @channels: array of channels which are passed to the driver
- * @num_channels: number of channels in the array
- *
- * This structure is passed to the DMA engine driver via platform data. For
- * M2P channels, contract is that even channels are for TX and odd for RX.
- * There is no requirement for the M2M channels.
- */
-struct ep93xx_dma_platform_data {
-	struct ep93xx_dma_chan_data	*channels;
-	size_t				num_channels;
-};
-
-static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
-{
-	if (device_is_compatible(chan->device->dev, "cirrus,ep9301-dma-m2p"))
-		return true;
-
-	return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
-}
-
-/**
- * ep93xx_dma_chan_direction - returns direction the channel can be used
- * @chan: channel
- *
- * This function can be used in filter functions to find out whether the
- * channel supports given DMA direction. Only M2P channels have such
- * limitation, for M2M channels the direction is configurable.
- */
-static inline enum dma_transfer_direction
-ep93xx_dma_chan_direction(struct dma_chan *chan)
-{
-	if (!ep93xx_dma_chan_is_m2p(chan))
-		return DMA_TRANS_NONE;
-
-	/* even channels are for TX, odd for RX */
-	return (chan->chan_id % 2 == 0) ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
-}
-
-#endif /* __ASM_ARCH_DMA_H */

-- 
2.41.0

Re: [PATCH v6 00/40] ep93xx device tree conversion

[Uwe Kleine-König]

[-- Attachment #1: Type: text/plain, Size: 1179 bytes --]

Hello,

On Tue, Dec 12, 2023 at 11:20:17AM +0300, Nikita Shubin via B4 Relay wrote:
> No major changes since last version all changes are cometic.
> 
> Following patches require attention from Stephen Boyd, as they were converted to aux_dev as suggested:
> 
> - ARM: ep93xx: add regmap aux_dev
> - clk: ep93xx: add DT support for Cirrus EP93xx
> 
> DMA related patches still require Acked or Reviewed tags.
> 
> got approval LGTM from Miquel:
> - mtd: rawnand: add support for ts72xx
> Link: https://lore.kernel.org/lkml/20231004103911.2aa65354@xps-13/
> 
> new patches:
> 
> ARM: ep93xx:  Add terminator to gpiod_lookup_table
>   - fixed terminator in gpiod_lockup_table
> 
> So mostly all patches got approval.
> 
> Patches should be now formated with '--histogram'

You didn't mention how this should be merged. IIRC for the earlier
rounds the idea was to merge it all together via arm-soc when all
necessary agreement is reached. I assume that's still the case here?

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v6 00/40] ep93xx device tree conversion

[Andy Shevchenko]

On Tue, Dec 12, 2023 at 11:20:17AM +0300, Nikita Shubin wrote:
> No major changes since last version all changes are cometic.
> 
> Following patches require attention from Stephen Boyd, as they were converted to aux_dev as suggested:
> 
> - ARM: ep93xx: add regmap aux_dev
> - clk: ep93xx: add DT support for Cirrus EP93xx
> 
> DMA related patches still require Acked or Reviewed tags.
> 
> got approval LGTM from Miquel:
> - mtd: rawnand: add support for ts72xx
> Link: https://lore.kernel.org/lkml/20231004103911.2aa65354@xps-13/
> 
> new patches:
> 
> ARM: ep93xx:  Add terminator to gpiod_lookup_table
>   - fixed terminator in gpiod_lockup_table
> 
> So mostly all patches got approval.
> 
> Patches should be now formated with '--histogram'

It _feels_ like some tags might be missing.
In any case I suggest to use `b4` tool to retrieve tags when preparing
the next version:

	git checkout -b vXX v6.7-rcX
	b4 am -slt $MSG_ID_OF_v(XX-1)
	git am ...
	git rebase --interactive ... # to address comments

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v6 10/40] dma: cirrus: Convert to DT for Cirrus EP93xx

[Andy Shevchenko]

On Tue, Dec 12, 2023 at 11:20:27AM +0300, Nikita Shubin wrote:
> Convert Cirrus EP93xx DMA to device tree usage:
> 
> - add OF ID match table with data
> - add of_probe for device tree
> - add xlate for m2m/m2p
> - drop subsys_initcall code
> - drop platform probe
> - drop platform structs usage
> 
> >From now only it supports only device tree probing.

"From now on it only..." (and single "only" is enough).

...

> +		edmac->clk = devm_clk_get(dev, dma_clk_name);
>  		if (IS_ERR(edmac->clk)) {
> +			dev_warn(dev, "failed to get clock\n");
>  			continue;
>  		}

This is incorrect, it doesn't handle deferred probe in two aspects:
- spamming the logs;
- not really trying to reprobe.

...

> +static bool ep93xx_m2p_dma_filter(struct dma_chan *chan, void *filter_param)
> +{
> +	struct ep93xx_dma_chan *echan = to_ep93xx_dma_chan(chan);
> +	struct ep93xx_dma_chan_cfg *cfg = filter_param;
> +
> +	if (cfg->dir == ep93xx_dma_chan_direction(chan)) {
> +		echan->dma_cfg = *cfg;
> +		return true;
> +	}
> +
> +	return false;

Perhaps

	if (cfg->dir != ep93xx_dma_chan_direction(chan))
		return false;

	echan->dma_cfg = *cfg;
	return true;

> +}

...

> +	if (!is_slave_direction(direction))
> +		return NULL;
> +
> +

One blank line is enough.

...

> +	switch (port) {
> +	case EP93XX_DMA_SSP:
> +	case EP93XX_DMA_IDE:
> +		break;
> +	default:
> +		return NULL;
> +	}

> +	if (!is_slave_direction(direction))
> +		return NULL;

This can be performed before switch, no?

...

> +#include <linux/device.h>
> +#include <linux/property.h>
> +#include <linux/string.h>
>  #include <linux/types.h>
>  #include <linux/dmaengine.h>
>  #include <linux/dma-mapping.h>

Perhaps make it a bit more ordered by squeezing to the (most) ordered parts?

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v6 40/40] dma: cirrus: remove platform code

[Andy Shevchenko]

On Tue, Dec 12, 2023 at 11:20:57AM +0300, Nikita Shubin wrote:
> Remove DMA platform header, from now on we use device tree for dma

DMA

> clients.

...

> +static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
> +{
> +	if (device_is_compatible(chan->device->dev, "cirrus,ep9301-dma-m2p"))
> +		return true;
> +
> +	return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
> +}

Hmm... Isn't the same as new helper in a header in another patch?

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v6 00/40] ep93xx device tree conversion

[Nikita Shubin]

Hello Andy!

On Wed, 2023-12-13 at 19:59 +0200, Andy Shevchenko wrote:
> On Tue, Dec 12, 2023 at 11:20:17AM +0300, Nikita Shubin wrote:
> > No major changes since last version all changes are cometic.
> > 
> > Following patches require attention from Stephen Boyd, as they were
> > converted to aux_dev as suggested:
> > 
> > - ARM: ep93xx: add regmap aux_dev
> > - clk: ep93xx: add DT support for Cirrus EP93xx
> > 
> > DMA related patches still require Acked or Reviewed tags.
> > 
> > got approval LGTM from Miquel:
> > - mtd: rawnand: add support for ts72xx
> > Link: https://lore.kernel.org/lkml/20231004103911.2aa65354@xps-13/
> > 
> > new patches:
> > 
> > ARM: ep93xx:  Add terminator to gpiod_lookup_table
> >   - fixed terminator in gpiod_lockup_table
> > 
> > So mostly all patches got approval.
> > 
> > Patches should be now formated with '--histogram'
> 
> It _feels_ like some tags might be missing.
> In any case I suggest to use `b4` tool to retrieve tags when
> preparing
> the next version:
> 
>         git checkout -b vXX v6.7-rcX
>         b4 am -slt $MSG_ID_OF_v(XX-1)
>         git am ...
>         git rebase --interactive ... # to address comments
> 

I moved to b4 a few iterations ago:

```
Calculating patch-ids from commits, this may take a moment...
Checking change-id "20230605-ep93xx-01c76317e2d2"
Grabbing search results from lore.kernel.org
Grabbing thread from lore.kernel.org/all/20230424123522.18302-1-
nikita.shubin%40maquefel.me/t.mbox.gz
---
NOTE: some trailers ignored due to from/email mismatches:
    ! Trailer: Tested-by: Michael Peters <mpeters@embeddedTS.com>
     Msg From: Kris Bahnsen <kris@embeddedTS.com>
NOTE: Rerun with -S to apply them anyway
No trailer updates found.
```

I haven't found any missing tags, that b4 didn't apply, the ones above
refer to a very old iteration and were given to cover letter and i
don't feel like they need to be included.

Re: [PATCH v6 40/40] dma: cirrus: remove platform code

[Nikita Shubin]

On Wed, 2023-12-13 at 20:30 +0200, Andy Shevchenko wrote:
> On Tue, Dec 12, 2023 at 11:20:57AM +0300, Nikita Shubin wrote:
> > Remove DMA platform header, from now on we use device tree for dma
> 
> DMA
> 
> > clients.
> 
> ...
> 
> > +static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
> > +{
> > +       if (device_is_compatible(chan->device->dev, "cirrus,ep9301-
> > dma-m2p"))
> > +               return true;
> > +
> > +       return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-
> > m2p");
> > +}
> 
> Hmm... Isn't the same as new helper in a header in another patch?
> 

Indeed it's internal now. Move here from platform header.

Re: [PATCH v6 00/40] ep93xx device tree conversion

[Andy Shevchenko]

On Sat, Dec 23, 2023 at 11:13 AM Nikita Shubin
<nikita.shubin@maquefel.me> wrote:
> On Wed, 2023-12-13 at 19:59 +0200, Andy Shevchenko wrote:

...

> I haven't found any missing tags, that b4 didn't apply, the ones above
> refer to a very old iteration and were given to cover letter and i
> don't feel like they need to be included.

When somebody gives you a tag against a cover letter, it means the
entire series (if not spelled differently). `b4` even has a parameter
-t for that IIRC.


-- 
With Best Regards,
Andy Shevchenko